through how many degrees does a 33 rpm turntable rotate in 0.32 sec ?

The height to which water would rise in the capillary tube with a radius of 5.4 x 10^-5 m is approximately 2.717 meters.

To find the height to which water would rise in a capillary tube with radius 5.4 x 10^-5 m, we can use the Jurin's Law formula:
h = (2 * S * cos(θ)) / (ρ * g * r)
where:
- h is the height of the liquid in the capillary tube
- S is the surface tension of the liquid (N/m) - for water, it's approximately 0.072 N/m
- θ is the contact angle between the liquid and the material of the tube - we assume it's zero, so cos(θ) = 1
- ρ is the density of the liquid (kg/m³) - for water, it's approximately 1000 kg/m³
- g is the acceleration due to gravity (9.81 m/s²)
- r is the radius of the capillary tube (5.4 x 10^-5 m)
Now we can plug in the values into the formula:
h = (2 * 0.072 * 1) / (1000 * 9.81 * 5.4 x 10^-5)
h ≈ 0.144 / (1000 * 9.81 * 5.4 x 10^-5)
h ≈ 0.144 / (5.2998 x 10^-2)
h ≈ 2.717 m
The height to which water would rise in the capillary tube with a radius of 5.4 x 10^-5 m is approximately 2.717 meters.

learn more about radius  here

https://brainly.com/question/20430163

SPJ11

The change in the angular momentum of the meterstick cannot be determined from this information.

An object's angular momentum is comparable to its linear momentum, which is defined as the mass in motion, except that the item is rotating as opposed to traveling in a straight line. We can think of angular momentum as the mass in rotation.

Change in angular momentum

ΔL = L(final) - L(initial)

ΔL = Iω,

where I = moment of inertia and

ω = angular velocity.

No information can be obtained from the question about angular velocity, hence we can't calculate the change in angular momentum.

Therefore, the change in the angular momentum of the meterstick cannot be determined from this information.

To know more about angular momentum, click here :

https://brainly.com/question/29563080

#SPJ12

The load, in amps, for a 3-phase, 208V feeder supplying a load calculated at 96.75kVA is approximately 268.64 Amps.

To calculate the load, in amps, for a 3-phase, 208V feeder supplying a load calculated at 96.75kVA, you can use the formula,

Load (Amps) = (kVA x 1000) / (Voltage x √3)

Where,
kVA = 96.75
Voltage = 208V
√3 = 1.732 (the square root of 3)

Multiply kVA by 1000 to convert it to VA.
96.75 x 1000 = 96750VA

Multiply voltage by the square root of 3.
208 x 1.732 = 360.256

Divide the VA value by the result from step 2.
96750 / 360.256 = 268.64 Amps

A 3-phase, 208V feeder's load in amps for feeding a 96.75kVA load is roughly equal to 268.64 Amps.

Learn more about "load": https://brainly.com/question/25543272

#SPJ11

The energy gained when a 2 kg mass is lifted by 2 m on Jupiter is 100 J.

To calculate the energy gained when a 2 kg mass is lifted by 2 m on Jupiter, we can use the formula:

E = mgh

where E is the energy gained, m is the mass, g is the acceleration due to gravity, and h is the height the object is lifted.

In this case, g = 25 N/kg, m = 2 kg, and h = 2 m. Substituting these values into the formula, we get:

E = (2 kg)(25 N/kg)(2 m) = 100 J

Therefore, the energy gained by Jupiter when a 2 kg mass is lifted by 2 m is 100 J.

To know more about Acceleration, here

brainly.com/question/12550364

#SPJ1

The direction of the vector c = 48i - 42j is approximately -41.19 degrees. Since the angle is negative, it means the vector c is in the fourth quadrant.

To find the direction of the vector c = 2a - b, we first need to calculate the components of the new vector c.
1. Multiply vector a by 2:
2a = 2(12i - 16j) = 24i - 32j
2. Subtract vector b from the result of step 1:
c = 2a - b = (24i - 32j) - (-24i + 10j) = 24i - 32j + 24i - 10j
3. Combine like terms:
c = 48i - 42j
Now that we have the components of vector c, we can find its direction. The direction of a vector can be calculated using the tangent inverse function (arctan):
θ = arctan(opposite/adjacent) = arctan(c_j/c_i) = arctan((-42)/48)
Use a calculator to find the arctan value:
θ ≈ -41.19 degrees

To learn more about vector click here https://brainly.com/question/29740341

#SPJ11

At 11 °C, the kinetic energy per molecule in a room is kave = 6.21 x 10^-21 J.

The kinetic energy per molecule in a gas is given by the formula:

KE = (3/2) kT

where KE is the kinetic energy per molecule, k is the Boltzmann constant (1.38 x 10^-23 J/K), and T is the temperature in Kelvin.

To convert a temperature from Celsius to Kelvin, we need to add 273.15 to the Celsius temperature.

So if the temperature is 11 °C, then the temperature in Kelvin is:

T = 11 °C + 273.15 = 284.15 K

Substituting this value into the formula for kinetic energy per molecule, we get:

KE = (3/2) kT = (3/2) (1.38 x 10^-23 J/K) (284.15 K)

KE = 6.21 x 10^-21 J

Therefore, at 11 °C, the kinetic energy per molecule in a room is kave = 6.21 x 10^-21 J.

Learn more about  kinetic energy

brainly.com/question/26472013

#SPJ11

The possible energies of photons emitted would be 2 eV, 3 eV, 5 eV, 10 eV, 12 eV, 15 eV, and 19 eV. The corresponding transitions on the diagram would be:

2 eV: State 3 to State 4

3 eV: State 2 to State 3

5 eV: State 2 to State 4

10 eV: State 4 to State 5

12 eV: State 3 to State 5

15 eV: State 2 to State 5

19 eV: State 1 to State 5

Transitions are words or phrases that connect different ideas within a piece of writing. They are used to help the reader move from one idea to another in a smooth and logical way. Transitions are an important part of writing because they help to create coherence and flow, making the text easier to read and understand.

Examples of transition words and phrases include "however," "moreover," "in addition," "on the other hand," "therefore," "consequently," "likewise," and "for instance." Using transitions in writing can improve the overall quality of the text by making it more organized, clear, and easy to follow. Transitions can be used in any type of writing, from academic essays to business reports to creative writing.

To learn more about Transitions visit here:

brainly.com/question/18089035

#SPJ4

The linear speed of an outer horse on the carousel can be calculated using the formula v = rω, where v is the linear speed, r is the distance from the axis of rotation, and ω is the angular velocity. Assuming that the carousel is rotating at a constant speed, we can use the formula v = rω to find the linear speed of the outer horse.

Given that the distance from the axis of rotation to the outer horse is 2.55 m, we can plug this value into the formula to get:

v = rω
v = (2.55 m)(ω)

However, we still need to find the value of ω. To do this, we need to know the period of rotation, which is the time it takes for the carousel to complete one full rotation. Let's assume that the period is 10 seconds.

The formula for angular velocity is ω = 2π/T, where T is the period of rotation. Plugging in the values we know, we get:

ω = 2π/T
ω = 2π/10 s
ω = 0.628 rad/s

Now we can use the formula v = rω to find the linear   linear

v = (2.55 m)(0.628 rad/s)
v = 1.6 m/s

Therefore, the linear speed of the outer horse on the carousel is 1.6 m/s.

Learn more about linear here:

https://brainly.com/question/15830007

#SPJ11

The final temperature of the mixture would be 50°C when 50 ml of water at 80°C is added to 50 ml of water at 20°C.

To determine the final temperature, we need to use the principle of conservation of energy, which states that the total energy in a closed system remains constant. In this case, we can assume that the two samples of water together form a closed system.
First, we need to calculate the amount of energy in each sample of water using the specific heat capacity formula:
q = m x c x ΔT
where q is the energy in Joules, m is the mass in grams, c is the specific heat capacity in J/g°C, and ΔT is the change in temperature in °C.
For the first sample of water at 80°C:
[tex]q_1 = 50 * 4.18 *(80 - T_1)[/tex]
where T1 is the final temperature we are trying to find.
For the second sample of water at 20°C:
[tex]q_2 = 50 *4.18 * (T_1 - 20)[/tex]
Now, since the total energy in the closed system remains constant, we can set q1 equal to [tex]q_2[/tex] and solve for [tex]T_1[/tex]:
[tex]50 * 4.18 * (80 - T_1) = 50 * 4.18 * (T_1 - 20)[/tex]
Simplifying the equation, we get:
[tex](80 - T_1) = (T_1 - 20)[/tex]
[tex]100 = 2T_1[/tex]
[tex]T_1[/tex] = 50°C
Therefore, the final temperature of the mixture would be 50°C.

Learn more about energy :

https://brainly.com/question/1371184

#SPJ11

The strength of the resulting magnetic field at a distance of 48.1 cm from the wire with a 22.9 A current is approximately 1.93 x 10⁻⁵ T.

Detailed explanation below:

The formula to be used is
B = (μ₀ * I) / (2 * π * r)

Step 1: Convert the distance to meters.
r = 48.1 cm * (1 m / 100 cm) = 0.481 m

Step 2: Plug the values into the formula.
B = (4π x 10⁻⁷ T·m/A * 22.9 A) / (2 * π * 0.481 m)

Step 3: Simplify the equation and solve for B.
B ≈ (9.274 x 10⁻⁶ T·m) / (0.481 m)
B ≈ 1.93 x 10⁻⁵ T

So, the strength of the resulting magnetic field at a distance of 48.1 cm from the wire with a 22.9 A current is approximately 1.93 x 10⁻⁵ T.

Learn more about magnetic field strength here:

"magnetic field strength at a distance in a straight conducting wire" https://brainly.com/question/18651668

#SPJ11

The scientist first credited for discovering the concept of inertia was Galileo. Option c is correct.

Galileo was an Italian physicist, mathematician, and astronomer who lived in the late 16th and early 17th century. He was one of the first scientists to study motion and is credited with discovering the concept of inertia, which is the tendency of a body at rest to remain at rest or a body in motion to remain in motion in a straight line at a constant velocity unless acted upon by a force.

Galileo discovered this concept through his experiments with moving objects, including rolling balls and falling objects, and his observations of the movements of the planets. His work laid the foundation for Isaac Newton's laws of motion, which are still used today to describe the behavior of objects in motion. Hence Option c is correct.

To learn more about concept of inertia, here

https://brainly.com/question/31322892

#SPJ4

The total power emitted by the transmitter, in Watts, is approximately 867,167 W. To find the total power emitted by the transmitter, we need to use the given information: distance from the transmitter (8 km), electric field strength (0.35 V/m), and the assumption that the transmitter radiates isotropically.

We also need the formula for the area of a sphere (4πr²).
Step 1: Convert the distance from kilometers to meters:
8 km = 8,000 meters

Step 2: Calculate the surface area of the sphere:
Area = 4πr² = 4π(8,000 m)² ≈ 804,247,719 m²

Step 3: Calculate the power density at the given distance (Power density = E²/120π):
Power density = (0.35 V/m)² / (120π) ≈ 1.08 × 10⁻³ W/m²

Step 4: Calculate the total power emitted by the transmitter (Power = Power density × Area):
Total power = 1.08 × 10⁻³ W/m² × 804,247,719 m² ≈ 867,167 W.

To know more about transmitter refer here:

https://brainly.com/question/2084370#

#SPJ11

The apparent power (S) is the total power in an AC circuit is 1200 VA, while the real power (P) is the power that is actually used to perform useful work, such as generating heat in the case of an electric heater is 1200 W.

In an AC circuit powering an electric heater, the apparent power (S) and real power (P) can be calculated using the formulas:

Apparent power (S) = Voltage (V) × Current (I)

Real power (P) = Apparent power (S) × Power factor (PF)

Given that the voltage (V) is 120 V and the current draw (I) is 10 A, we can substitute these values into the formulas to compute the apparent power and real power.

Apparent power (S) = 120 V × 10 A = 1200 VA (volt-amperes)

The apparent power (S) represents the total power in the circuit, which includes both the real power (P) and the reactive power (Q) due to the inductance or capacitance in the circuit.

The power factor (PF) is given as 1.0, which indicates that the circuit has a purely resistive load (the electric heater), and there is no reactive power component. Therefore, the real power (P) is equal to the apparent power (S).

Real power (P) = Apparent power (S) × Power factor (PF) = 1200 VA × 1.0 = 1200 W (watts)

The real power (P) represents the actual power consumed by the electric heater and is the power that is used to generate heat. It is the power that is useful and converted into the desired output (heat) in this case.

In summary, the power factor (PF) indicates the efficiency of power utilization in the circuit, with a higher power factor indicating a more efficient utilization of power.

You can learn more about apparent power at: brainly.com/question/31116183

#SPJ11

It takes 4.7ms for the current to drop from its initial value to 1.30mA.

We can solve for the time t when the current drops to 1.30mA by setting I(t) equal to 1.30mA and solving for t:

[tex]1.30mA = I0e^(-t/\tau)[/tex]

ln(1.30mA/I0) = -t/τ

Solving for t, we get:

t = -ln(1.30mA/I0) * τ

I0 = V/R = 16.0V / 4.0kohm = 4.0mA

Substituting into the equation for t, we get:

t = -ln(1.30mA/4.0mA) * 7.4ms = 4.7ms

Current refers to the flow of electric charge in a circuit or medium. It is measured in amperes (A) and is denoted by the symbol "I." The flow of current can be either direct or alternating. Direct current (DC) flows continuously in one direction, while alternating current (AC) changes direction periodically.

The flow of current is facilitated by the presence of a voltage difference or potential difference between two points in a circuit or medium. This voltage difference causes electrons to flow from a higher potential to a lower potential, thereby creating a flow of current. The rate of flow of current is dependent on the resistance of the medium through which it flows.

To learn more about Current visit here:

brainly.com/question/12618565

#SPJ4

The substitution of machinery that has sensing and control devices for human labor is best described by the term: d. automation

The best term to describe the substitution of machinery that has sensing and control devices for human labor is "automation". Automation involves the use of machinery with advanced control devices and sensors to perform tasks that were previously done by humans. This can lead to increased efficiency and productivity, but can also result in the loss of jobs for human workers. Automation can be used to replace physical labor, reduce workloads, minimize mistakes, and increase efficiency. Automation can also be used to increase safety by having machines perform tasks that are too dangerous for humans, such as handling hazardous materials.

To learn more about automation click here https://brainly.com/question/28222698

#SPJ11

The final angular speed of the discus is 113.8 rad/s, and the magnitude of the angular acceleration of the discus is 347.6 rad/s².

To find the final angular speed of the discus, we can use the equation:

ω² = ω0² + 2αθ

where ω will be the final angular speed, ω0 will be the initial angular speed (which is zero), α will be the angular acceleration, and θ is the angle through which the discus is whirled.

We know that θ = 1.30 rev, which is equivalent to 2π(1.30) = 8.168 radians, and the radius of the circle on which the discus moves is 1.04 m. Therefore, the distance traveled by the discus is;

s = rθ = (1.04 m)(8.168 rad) = 8.502 m

We also know that the final speed of the discus is 25.9 m/s, so we can find the time it takes to reach this speed;

v = at

25.9 m/s = a t

t = 25.9/a

where a is the linear acceleration of the discus.

Since the distance traveled by the discus is equal to the circumference of the circle on which it moves, we can find the time it takes to travel this distance;

t = s/v = 8.502 m / 25.9 m/s = 0.328 s

Therefore, we have;

t = 25.9/a

0.328 s = 25.9/a

a = 79.02 m/s²

Now we can use the equation above to find ω;

ω² = 2αθ

ω² = 2(79.02 m/s²)(8.168 rad)

ω² = 12945.76

ω = 113.8 rad/s

Therefore, the final angular speed of the discus will be 113.8 rad/s.

To find the angular acceleration of the discus, we can use the equation;

α = (ω - ω0) / t

where ω will be the final angular speed, ω0 will be the initial angular speed (which is zero), and t is the time it takes for the discus to reach this speed.

We already know that ω = 113.8 rad/s and that t = 0.328 s, so we have;

α = (113.8 rad/s - 0 rad/s) / 0.328 s

α = 347.6 rad/s²

Therefore, the magnitude of the angular acceleration of the discus is 347.6 rad/s².

To know more about angular speed here

https://brainly.com/question/14663644

#SPJ4

The total current flowing in the circuit is approximately 6.2 A.

To calculate the total current flowing in a parallel circuit with resistors, you first need to find the equivalent resistance (Req) using the formula:

1/Req = 1/R1 + 1/R2 + 1/R3

In this case, R1 = 4.0 ω, R2 = 6.0 ω, and R3 = 10.0 ω.

1/Req = 1/4.0 + 1/6.0 + 1/10.0
1/Req = 0.25 + 0.1667 + 0.1
1/Req = 0.5167

Now, find the equivalent resistance:
Req = 1 / 0.5167 ≈ 1.935 ω

Next, apply Ohm's Law to calculate the total current (I) using the formula:

I = V / Req

Here, V = 12V (battery voltage) and Req ≈ 1.935 ω.

I = 12V / 1.935 ω ≈ 6.2 A

Therefore, the total current flowing in the circuit is approximately 6.2 A.

To learn more about resistance, refer below:

https://brainly.com/question/30799966

#SPJ11

When a DC motor with three phases is in operation, it is true that only two of the three phases are energized at any given time. The specific phase that is de-energized depends on the position of the rotor.

The rotor is attracted to the magnetic field produced by the energized phases, so as the rotor rotates, the phases that are energized change in a specific sequence. This sequence is controlled by the motor controller and is designed to produce smooth and efficient operation of the motor.

Therefore, the phase that is de-energized at any given time is determined by the controller's sequence and the position of the rotor.

A direct current (DC) motor is a type of electric machine that converts electrical energy into mechanical energy. DC motors take electrical power through direct current, and convert this energy into mechanical rotation.

To know more about DC motor:https://brainly.com/question/15721280

#SPJ11

Therefore, wavelength with a displacement amplitude of [tex]1.2 * 10^{-8} m[/tex] that produces a pressure amplitude of [tex]1.5 * 10^{-3}[/tex] Pa have a frequency of approximately.

Part A: The speed of sound in air is given as vsound = 344 m/s. The formula for the speed of a wave is given as:

v = λf

λ = v/f

Substituting the values given, we have:

λ = 344 m/s / 1000 Hz = 0.344 m

Therefore, the wavelength of these waves is 0.344 m.

Part B:

Displacement amplitude needed for the pressure amplitude to be at the pain threshold, we can use the formula for the pressure amplitude in terms of displacement amplitude:

P = ρvsoundωA

A = P / (ρvsoundω)

Substituting the values given, we have:

A = 30 Pa / (1.2 kg/m³ × 344 m/s × 2π × 1000 Hz) ≈ [tex]2.03 * 10^{-7} m[/tex]

Therefore, the displacement amplitude needed for the pressure amplitude to be at the pain threshold is approximate  [tex]2.03 * 10^{-7} m[/tex].

Part C: We can use the same formula as in Part B, but solve for the wavelength instead of the displacement amplitude. Rearranging the formula gives:

λ = 2πA / ω

ω = 2πf = 2π × 1000 Hz = 2000π rad/s

[tex]A = 1.2 * 10^{-8} m\\P = 1.5 * 10^{-3} Pa[/tex]

ρ = 1.2 kg/m³

vsound = 344 m/s

Using the formula, we have:

λ = 2π × 1.2 × [tex]10^{-8} m[/tex] / (2000π rad/s) ≈ 3.80 × [tex]10^{-12[/tex] m

Therefore, the wavelength for waves with a displacement amplitude of 1.2 × 10^-8 m that produce a pressure amplitude of 1.5 × [tex]10^{-3[/tex] Pa is approximately 3.80 × [tex]10^{-12[/tex] m.

Part D: Again, we can use the same formula as in Part B, but solve for the frequency instead of the displacement amplitude. Rearranging the formula gives:

f = ω / 2π

Substituting the values given, we have:

ω = 2πf

[tex]A = 1.2 * 10^{-8 }m\\P = 1.5 * 10^{-3 }Pa[/tex]

ρ = 1.2 kg/m³

vsound = 344 m/s

A = P / (ρvsoundω) = P / (ρvsound × 2πf)

f = ω / 2π = P / (2πρvsoundA)

f =  ≈ 9589 Hz

Learn more about wavelength visit: brainly.com/question/24452579

#SPJ4

C.

The block would try to push down due to it's weight.

Venus' rotation is retrograde and slow.

This means that it rotates in the opposite direction to most other planets, including Earth, and takes a longer time to complete one full rotation. The reason for this is still not fully understood, but some theories suggest that it may have been caused by a collision with a large object in the past or by the gravitational influence of the sun and other planets. In any case, Venus' rotation is quite different from Earth's, which rotates in a prograde direction and completes one full rotation in about 24 hours.
Its rotation is also slow, taking about 243 Earth days to complete one rotation. The exact cause of this retrograde and slow rotation is still a subject of scientific research, but it is likely due to a combination of factors, such as gravitational interactions and past impacts.

To know more about retrograde and slow click here:

https://brainly.com/question/30009307

#SPJ11

The correct option is C, Venus' rotation is retrograde and slow.

Venus is a planet in our solar system, named after the Roman goddess of love and beauty. In physics, Venus is primarily studied in the context of planetary science and astrophysics. Its physical characteristics include a diameter of approximately 12,104 kilometers, a mass of 4.87 x 10^24 kilograms, and a surface temperature of around 462 degrees Celsius, making it the hottest planet in our solar system.

Venus has a thick atmosphere primarily composed of carbon dioxide, which creates a strong greenhouse effect that traps heat and contributes to its high surface temperature. It also has a weak magnetic field and experiences a slow retrograde rotation, meaning it rotates in the opposite direction to most planets in our solar system. Venus' unique properties and proximity to Earth make it a valuable subject for scientific research and exploration, including missions by NASA and other space agencies.

To learn more about Venus visit here:

brainly.com/question/26773278

#SPJ4

The induced EMF in the coil will vary sinusoidally between 0 and 0 volts, with a frequency of 3200/60 = 53.3 Hz.

Using the given information, we can calculate the EMF induced in the coil using the equation: EMF = NABωsinθ

where N is the number of turns in the coil, A is the area of the coil, B is the magnetic field strength, ω is the angular velocity of the coil, and θ is the angle between the magnetic field lines and the normal to the coil.

First, we need to find the area of the coil:

A = πr^2

A = π(0.19/2)^2

A = 0.028 m^2

Next, we can calculate the angular velocity:

ω = 2πf

ω = 2π(3200/60) (converting from rpm to Hz)

ω = 335.1 rad/s

Now we can calculate the EMF induced in the coil for a random value of θ: EMF = NABωsinθ

EMF = (200)(0.028)(0.75)(335.1)sinθ

EMF = 1418.8sinθ volts

The value of θ will vary randomly between 0 and 2π, so the maximum and minimum values of the induced EMF can be found by substituting these values into the equation above:

EMFmax = 1418.8sin(2π) = 0 volts

EMFmin = 1418.8sin(0) = 0 volts

Therefore, the induced EMF in the coil will vary sinusoidally between 0 and 0 volts, with a frequency of 3200/60 = 53.3 Hz.

To learn more about EMF here:

https://brainly.com/question/15121836

#SPJ11

Answer: 3.24 * 10^-4 ohms

Explanation:

For this question, we will use the equation R = p L/A. R represents resisatnce, p is resistivity, L is length, and A is area.

p = 1.61 * 10^-8 ohm-meters

L = 20.4 m

A = (area of a circle)

- Convert diameter into radius (and the correct units): 2.047/2 * 10 ^-3.

Now plug them into the equation.

Initially, a single capacitance C1 is wired to a battery. Then capacitance C2 is added in series.

(e) When capacitance C2 is added in series to capacitance C1:the equivalent capacitance C12 of C1 and C2 is less than C1, and the equivalent capacitance C12 = (C1C2)/(C1 + C2)

As, the capacitances are in series, and the total potential difference V across them would be equal to the sum of the potential differences across them.

So, the potential difference across C1 will be less than the previous potential difference across C1 when only capacitance C1 was connected to the battery.

The formula for potential difference across capacitance C1 would be: V = Q1/C1, where Q1 is the charge stored in capacitance C1.

As the potential difference V decreases and C1 remains the same, the charge Q1 on C1 would also decrease. Thus, (i) the potential difference across C1 and (ii) the charge q1 on C1 is now less than previously.

Know more about capacitance:

https://brainly.com/question/31871398

#SPJ12

Conservation of Momentum states d. That the total momentum of an isolated system remains constant

This means that in a closed system where no external forces are acting, the total momentum of the system will remain constant. This principle is similar to the principle of conservation of energy, where the total energy of a closed system remains constant. Momentum is a property of moving objects and is calculated by multiplying the mass of an object by its velocity.

If an object in a system loses momentum, another object in the same system must gain an equal amount of momentum to maintain the total momentum of the system. This principle is observed in all systems, from subatomic particles to celestial bodies. Understanding the conservation of momentum is essential in fields such as physics and engineering, as it can help predict the behavior of systems and the outcomes of collisions or other interactions between objects. Conservation of Momentum states d. that the total momentum of an isolated system remains constant.

Learn more about momentum at:

https://brainly.com/question/31336310

#SPJ11

The merry-go-round stops spinning. When you grab the edge of the merry-go-round wheel with your hand, the friction force between your hand and the wheel causes the wheel to slow down and eventually come to a stop.

The direction of rotation before you stopped the wheel will determine the direction it rotates after you stop it.

If the wheel was rotating clockwise before you stopped it, it will rotate counterclockwise after you stop it, and vice versa.

This is due to the conservation of angular momentum, which states that the total amount of angular momentum in a closed system remains constant unless acted upon by an external torque.

For more such questions on friction force, click on:

https://brainly.com/question/24338873

#SPJ11

A) To calculate the number of kilometers the car can drive on a fully charged battery, we need to divide the total energy of the battery (60 kWh) by the energy consumed per kilometer (200 Wh/km).

60,000 Wh / 200 Wh/km = 300 km

Therefore, the car can drive 300 kilometers on a fully charged battery.

B) If the battery current drain during driving is at 100 A, we can calculate the number of hours the car can drive at this discharge current by dividing the total energy of the battery (60 kWh) by the power consumed (voltage x current).

P = V x I

P = 350 V x 100 A = 35,000 W

60,000 Wh / 35,000 W = 1.7 hours

Therefore, the car can drive for 1.7 hours at a discharge current of 100 A.

C) If the electricity cost is 0.15 cents per kWh, we can calculate the cost to charge the battery pack by multiplying the energy of the battery (60 kWh) by the electricity cost (0.15 cents/kWh) and converting it to dollars.

60 kWh x 0.15 cents/kWh = 9 dollars

Therefore, it costs 9 dollars to charge the battery pack at an electricity cost of 0.15 cents per kWh.
Hi there! I'd be happy to help you with your electric vehicle question.

A) To determine how many kilometers the car can drive on a fully charged battery, divide the battery energy by the vehicle's energy consumption:

60 kWh / (200 Wh/km) = (60,000 Wh) / (200 Wh/km) = 300 km

The car can drive 300 kilometers on a fully charged battery.

B) To find how many hours the car can drive at a discharge current of 100 A, first calculate the power being used:

Power = Voltage x Current = 350 V x 100 A = 35,000 W (or 35 kW)

Next, divide the battery energy by the power being used:

60 kWh / 35 kW = 1.714 hours

The car can drive for 1.714 hours at this discharge current.

C) To calculate the cost to charge the battery pack, multiply the battery energy by the electricity cost:

60 kWh x $0.15/kWh = $9

It costs $9 to charge the battery pack.

I hope this helps! If you have any further questions, feel free to ask.

Learn more about battery energy by the electricity here;

https://brainly.com/question/31238327

#SPJ11

The wavelength (λ) of the wave can be found using the formula λ = c/f, where c is the speed of light in vacuum (3 × 10^8 m/s) and f is the frequency. Substituting the given values, we get:

λ = (3 × 10^8 m/s)/(2.20 × 10^10 Hz) = 0.0136 m = 13.6 mm

The distance between adjacent nodal planes of the E⃗ field (which is perpendicular to the B⃗ field) is half the wavelength, so it is:

(1/2)λ = (1/2)(0.0136 m) = 0.0068 m = 6.8 mm

The speed of propagation of the wave can be found using the formula v = fλ, where v is the speed and f and λ are the frequency and wavelength, respectively. Substituting the given values, we get:

v = (2.20 × 10^10 Hz)(0.0136 m) = 2.99 × 10^8 m/s

Note that the speed of propagation in a material can be different from the speed of light in vacuum, which is why we use the given frequency and nodal plane separation to calculate the wavelength and speed in this specific material.
Given the frequency of the standing electromagnetic wave is 2.20 × 10^10 Hz, and the distance between the nodal planes of the magnetic field (B⃗) is 4.35 mm.

1. To find the wavelength of the wave in this material, we can use the relationship between the distance between nodal planes and wavelength: the distance between nodal planes is half the wavelength. Therefore:

Wavelength (λ) = 2 * distance between nodal planes
λ = 2 * 4.35 mm
λ = 8.70 mm

2. The distance between adjacent nodal planes of the electric field (E⃗) is the same as the distance between the nodal planes of the magnetic field (B⃗), which is 4.35 mm.

3. To find the speed of propagation of the wave, we can use the formula:

Speed (v) = Frequency (f) * Wavelength (λ)
v = 2.20 × 10^10 Hz * 8.70 × 10^-3 m (converting mm to meters)
v = 1.914 × 10^8 m/s

In summary, the wavelength of the wave in this material is 8.70 mm, the distance between adjacent nodal planes of the E⃗ field is 4.35 mm, and the speed of propagation of the wave is 1.914 × 10^8 m/s.

Learn more about wavelength here;

https://brainly.com/question/13533093

#SPJ11

The focal length of the lens is 40 cm, and the image is located at infinity.

The focal length of a lens can be determined using the lensmaker's equation;

1/f=(n - 1) × (1/R₁ - 1/R₂)

where f is the focal length of the lens, n is the refractive index of the lens material (in this case, n = 1.5), R₁ is the radius of curvature of one side of the lens (in this case, R₁ = infinity for the flat side), and R₂ is the radius of curvature of the other side of the lens (in this case, R₂ = 20 cm for the convex side).

Plugging in the values, we get;

1/f = (1.5 - 1) × (1/infinity - 1/20)

1/f = 0.5 × (-1/20)

1/f = -0.025

f = -40 cm

Note that the negative sign indicates that the lens is a converging lens (i.e., it brings parallel light rays to a focus).

Therefore, the focal length of the lens will be 40 cm.

To find the location of the image formed by the lens, we can use the thin lens equation;

1/o + 1/i = 1/f

where o is the object distance (the distance of the object from the lens), i is the image distance (the distance of the image from the lens), and f is the focal length of the lens.

Plugging in the values, we get;

1/40 + 1/i = 1/40

1/i = 0

This indicates that the image is formed at infinity (i.e., the light rays are parallel after passing through the lens).

Therefore, the image is located at infinity.

To know more about focal length here

https://brainly.com/question/16188698

#SPJ4

None of these spectra will produce significant X-ray light, as the temperatures are not high enough to emit light at such short wavelengths (0.001 microns).

The spectrum for T=5000 K produces more light in the blue part of the visible spectrum.
The spectrum for T=5000 K produces more light in the blue part of the visible spectrum.

Among the blackbody spectra shown in Question 5, the spectrum for T=3000 K produces more light in the infrared part of the spectrum.

None of these spectra will produce significant X-ray light, as the temperatures are not high enough to emit light at such short wavelengths (0.001 microns).

To know more about visible spectrum. click here:

brainly.com/question/18704022

#SPJ11