Steel angle is not an example of a cold-formed steel product.
What is steel?
In order to increase its strength and resistance to fracture in comparison to other kinds of iron, steel is an alloy composed of iron and often contains a few tenths of a percent of carbon. Many additional components could be included or added. An additional 11% chromium is often required for corrosion- and oxidation-resistant stainless steels. Steel is utilised in structures, infrastructure, tools, vehicles, machinery, electrical appliances, weaponry, and rockets due to its great tensile strength and low price. Steel's foundational metal is iron. It can take one of two crystalline (allotropic) forms, body-centered cubic or face-centered cubic, depending on the temperature. Steel and cast iron's variety of special qualities are a result of the interaction of the various iron allotropes with the alloying elements, primarily carbon.
To learn more about steel
https://brainly.com/question/26654853
#SPJ4
determine the vertical displacements at the center and ends of the loaded shaft indicated below. use the method of conjugate-beam and assume that ei is constant (60 pts).
The vertical displacement at the center of the loaded shaft is zero. The vertical displacement at the end of the loaded shaft is equal to the length of the shaft multiplied by the slope of the shaft.
What is vertical displacement?
Vertical displacement in tectonics refers to the movement of land inside a vertical direction, which causes uplift and subsidence. Rock layer displacement can reveal information about how and why the lithosphere of Earth evolves over the course of geologic time. Vertical displacement can be caused by a variety of processes, including isostatic adjustments and tectonic activity. When crust is reorganised as a result of a seismic event, tectonic activity causes vertical displacement. Vertical displacement as a result of sinking from an increased load and isostatic rebound from a removed load is the outcome of isostatic corrections. At the margins of convergent and divergent plate boundaries, tectonic activity results in vertical displacement. As the magma begins to rise to protrude weaker lithospheric crust, the movement of the magma in the asthenosphere can cause divergent plate boundaries.
To learn more about vertical displacement
https://brainly.com/question/24004804
#SPJ4
rod abc consist of two cylindrical portions ab and bc; it is made of a mild steel that is assumed to be elastoplastic with e
Two cylindrical parts, AB and BC, make up the rod ABC. It is constructed of mild steel, which is assumed to be elastoplastic with E=200GPa and Y=250 megabytes MPa.
One of the steels has a 25C starting temperature. What the two kids gave us were models of the material's flexibility. We continue to receive 200 GB. The degree of services and linear expansion coefficients are the same for all four.
The boy from extra sigma concurs. 250 megabytes of data were shot out. We must ascertain the level of stress on field road. The street road is visible. All for P. Health minus P. L. is equivalent. We can express this as having all four delta T because both of the responses were acceptable. All four of the sigma are equal to delta T. He consented to us slipping the numbers so we could calculate the temperature rise. is a temporary power of six equal to 250.
To know more about megabytes click here:
https://brainly.com/question/2575232
#SPJ4
although the mechanism of the coupling process is not well understood, it is known that it rate appears to depend on the square of the concentration of the halide. with this in mind, explain the reason for the sequence of addition of the ether solution employed at the beginning of the formation of the grignard reagent in the experimental procedure above.
The sequence of addition of the ether solution is employed to prevent the grignard reagent from decomposing. The mechanism of the coupling process is not well understood, but it is known that the rate of the coupling process appears to depend on the square of the concentration of the halide.
What is employed?
A person who is employed either has a job or is engaged in something. Some individuals think that teenagers with employment are less likely to get into trouble than those without work. You are employed if you are working. The majority of persons who are working hold traditional full-time occupations, however an increasing proportion also work as independent contractors or in part-time jobs. This adverb can also be used to denote "used," as in the sentence "The used tactics for maintaining the classroom's quiet seem a touch extreme to me." The word employ, which means to "use, apply, occupy, or hire," is whence the adjective employed originates.
To learn more about employed
https://brainly.com/question/28016559
#SPJ4
Which of the following Belt Levels usually require a Six Sigma Project be completed before a Six Sigma Certification is awarded?
A . White Belt
B . Yellow Belt
C . Green Belt
D . Black Belt
E . Master Black Belt
F . None of the Above
G . All of the above
It is to be noted that "All of the above" (Option G) Belt Levels must be completed before a Six Sigma Certification is awarded.
What is a Six Sigma Certification?Six Sigma is a certification program that teaches employees how to analyze processes and results in the objective of eliminating waste and faults. There are numerous levels of certification, ranging from main end user to master Six Sigma user.
Six Sigma is a quality control certification that teaches employees how to analyze processes and outcomes in order to eliminate waste and faults. Certification levels range from primary end user to master Six Sigma user who serves as a senior quality control member.
It is to be noted that the ASQ Six Sigma Black Belt exam is a demanding and tough exam. The disciplined study, experience, and a solid preparation and test-taking plan are required. Many students study for months and then fail.
Learn more about Six Sigma:
https://brainly.com/question/16180406
#SPJ1
2. (50 points) understanding mips add comments to each line of the following mips code and describe in a sentence or two what it computes. assume that $a0 is used for the input and initially contains n, a positive integer. assume that $v0 is used for returning the output value. begin: addi $t0, $zero, 0 // addi $t1, $zero, 1 // loop: slt $t2, $a0, $t1 // bne $t2, $zero, finish // add $t0, $t0, $t1 // addi $t1, $t1, 2 // j loop // finish: add $v0, $t0, $zero //
Comments are added to each line of the following mips code and describe in a sentence.
#t0=sum=0 commont for first code
#t1=i=1
# (n<i)? or (i>n)?
# exit loop if (i>n)
# sum = sum + 1
# i = i + 2
# repeat loop
# result = sum
Result $v0 is the sum of the odd positive integers 1 + 3 + 5 + … which are less than or equal to n.
A comment in computer program is an explanation or annotation that can be read by programmers and is included in the source code of a computer program. They are added to the source code to make it simpler for humans to understand it, and compilers and interpreters typically ignore them.
Learn more about code here:
https://brainly.com/question/14461424
#SPJ4
Which of the following correctly demonstrates the use of an array initializer list? Choose all that apply. int[] my_array = {1, 2, 3, 4, 5); int[] my_array = [1, 2, 3, 4, 5]; int my_array = (1,2,3,4,5); int my_array = new {1, 2, 3, 4, 5); none of these
int[] my_array = {1, 2, 3, 4, 5}; correctly demonstrates the use of an array initializer list.
What is an array?
An array is a data structure in computer science that consists of a collection of elements, each of which is identified by at least one array index or key. A mathematical method is used to compute the position of each element from its index tuple in an array. An array of ten 32-bit (4-byte) integer variables with indices 0 through 9 may, for example, be stored as ten words at memory addresses 2000, 2004, 2008,..., 2036, with the element with index I having the address 2000 + I 4).
To learn more about array
https://brainly.com/question/28632808
#SPJ4
which microphone preamplifier input impedance would be best for a microphone that has an output impedance of 100 ohms?
A microphone preamplifier with an input impedance of 1,000 ohms would be best for a microphone that has an output impedance of 100 ohms.
What is microphone preamplifier?
The electronic circuitry found inside a microphone or a different object or circuit to which the microphone is linked can both be referred to as microphone preamplifiers. The microphone preamplifier serves the same role in either scenario. A microphone preamplifier is a piece of sound engineering gear that gets a microphone signal ready for other gear to handle. Frequently, microphone signals are too weak to be adequately conveyed to equipment like mixing consoles and recording devices. Preamplifiers boost a microphone signal to line level by offering steady gain and reducing generated noise, which would otherwise cause the signal to be distorted. See Gain stage for more discussion on signal level. Informally, a microphone preamplifier is referred to as a mic preamp, micamp, preamp, mic pre, and pre.
To learn more about microphone preamplifier
https://brainly.com/question/15735185
#SPJ4
You want to make interface fa0/2 a memeber of VLAN2 on a Catalyst 2950XL switch. Which commands must you enter?
The commands you must enter to make fa0/2 a member of VLAN2 on a catalyst 2950XL switch is int fastEthernet 0/2 and switchport access vlan 2
The display port-security connection fastethernet 0/2 command displays a connection in a secure manner, suggesting that it's been disabled due to security controls. In this situation, another device connected to port F0/2 is causing a violation by delivering a frame with such a destination MAC address apart from 0200.1111.1111. Rejoins connection variety design mode, allowing you can configure the very same variables on many channels at the same moment. To convert a port or a group of ports into accessible ports, just use the interface configuration entry VLAN command. A port in accessible mode has only one VLAN defined on the connection, and it is only able to carry traffic for one VLAN. On a Cisco IOS, this interface configuration accessible VLAN function creates a Layer 2 interface.
Learn more about fastethernet 0/2 and switchport access vlan 2 here: https://brainly.com/question/27874920
#SPJ4
5. Technician A says that a direct report program is repair program that directly involves the insurar company, the repair shop, the original equipme manufacturer, and the agent that sold the polic Technician B says that blending an undamaged panel is also referred to as "fooling the custom Who is correct?
A. Technician A only
B. Technician B only
C. Both Technicians A and B
D. Neither Technician A nor B
It can be inferred from the above that "Neither Technician A nor B is correct" (Option D). Note that blending an undamaged vehicle panel is required when there is very minimal damage or dent to the panel. In this case, the technician utilizes filling, spraying, and polishing to hide the dent. This is standard practice and is not considered fooling the customer.
What is a blend within the panel?When repairing a minor dent in a panel, the "blend inside panel" approach is frequently utilized. Blending is a method used on a non-repaired, undamaged panel to eliminate color differences between a refinished panel and the existing paint on surrounding panels.
The most typical blending process seen on insurance quotes is on bumpers and doors. Insurers pay half the restore time and then approve full clear, significantly cutting refinishing time by an hour for each repair.
From a 320-grit completed mended area, the repaired area still has to be brought up to refinish requirements.
Not only has a part of the refinish time been wasted, but extra operations are required to restore the panel to its original, undamaged state. Most estimate P pages include refinishing timelines for fresh, undamaged panels, rather than those that require preparation.
Learn more about damaged panels:
https://brainly.com/question/13543219
#SPJ1
consider the following page reference string:
7,2,3,1,2,5,3,4,6,7,7,1,0,5,4,6,2,3,0,1.
Assuming demand paging with paging with three frames, how many page faults would occur for the following replacement algorithms?
a. LRU replacement
b. FIFO replacement
c. Optimal replacement
Assuming demand paging with three frames, the number of page faults that would occur for the following replacement algorithms are:
Using LRU Replacement Algorithm: 18 Page Faults.Using FIFO replacement Algorithm: 17 page FaultsUsing Optimal Replacement Algorithm: 13 Page Faults.What is demand Paging?
Demand paging is a way of managing virtual memory in computer operating systems. In a demand paging system, the operating system transfers a disk page into physical memory only if it is attempted to be accessed and the page is not already in memory.
The LRU page replacement method creates a new page by replacing the least recently used page in memory. The LRU page replacement technique is based on the idea that the least recently used page in memory will not be utilized for a long period.
The most basic page replacement technique is the FIFO Replacement Algorithm. In this technique, the operating system maintains a list of all pages in memory in a queue, with the oldest page at the top.
The best page replacement algorithm is optimal page replacement since it produces the fewest number of page defects. The pages that will not be utilized for the greatest period of time in the future are replaced by this algorithm.
Learn more bout page faults:
https://brainly.com/question/24128255
#SPJ1
Consider the following Point2D class.
public class Point2D
{
private double xCoord;
private double yCoord;
public Point2D(double x, double y)
{
xCoord = x;
yCoord = y;
}
}
Which of the following code segments, appearing in a class other than Point2D, will correctly create an instance of a Point2D object?
A Point2D p = (3.0, 4.0);
B Point2D p = Point2D(3.0, 4.0);
C new p = Point2D(3.0, 4.0);
D new Point2D = p(3.0, 4.0);
E Point2D p = new Point2D(3.0, 4.0);
Appearing in a class other than Point2D, will correctly create an instance of a Point2D object is:
E Point2D p = new Point2D(3.0, 4.0);
What is Point2D?
The Point2D class is part of JavaFX. This class represents a two-dimensional point in space. The Point2D class represents a 2D point by its x and y coordinates. We can construct three Point2D objects named point2d 1, point2d 2, and point2d 3 by supplying their x and y coordinates as inputs. We use the getX() and getY() functions to obtain the x and y values, which we then display. We are also computing and displaying the distance of each point from the origin. We also show if two points are equal or not using the equals() method and the distance between two points using the distance() function.
To learn more about Point2D
https://brainly.com/question/3405843
#SPJ4
Which of the following is an example of an advantage that a modern inventory management system provides? More than one answer may be selected. Check All That Apply A. Automatic reordering occurs when inventory levels dip below a pre-established threshold. B. Production is scaled up or scaled down depending on the pace of orders received and the amount of inventory currently available. C. Competing products are quickly developed based on products that have shown initial success. D. RFID tags that are part of a GIS system are included with manufactured goods once assembly is
Automatic reordering occurs when inventory levels dip below a pre-established threshold.
What is modern inventory management?The process of tracking and managing your company's inventory as it is purchased, produced, stored, and used is known as inventory management.It controls the complete flow of goods, from procurement to sale, ensuring that you always have the appropriate numbers of the appropriate item at the appropriate location at the appropriate time. When the amount of stock on hand hits a pre-set reorder point, an automatic reordering system places an order for the product.A computer can provide an automatic reorder based on calculations for the reorder point and a perpetual inventory system. An order that is manually entered by a member organization signifies that it was not entered into an electronic order-routing or execution system.To learn more about inventory management refer
https://brainly.com/question/13439318
#SPJ4
the left rear brake drum is scored, but the right rear drum looks as good as new. technician a says the left-side drum should be resurfaced and the right-side drum should be reinstalled without resurfacing. technician b says both sides should be remachined to a similar diameter. who is correct?
Technician b is correct because the left rear brake drum is scored, but the right rear drum looks as good as new then both sides should be remachined to a similar diameter.
A brake drum is a revolving cylinder-shaped component that is friction-activated by a set of shoes or pads pressing outward against it. Drum brakes are brakes where shoes are pressed against the inner surface of the drum. Drum brakes are frequently used at the rear. Compared to disc brakes, these brakes have more parts and are more difficult to maintain, but they cost less to make and are simple to add an emergency braking mechanism. The front and rear brakes are standard equipment on all automobiles. Your car may have a "disc brake" system on all four wheels, a "drum brake" system on all four wheels, or a combination of the two. Typically, the front brakes of your car have a disc system, and the rear brakes have a drum system.
Learn more about brake drum here:
https://brainly.com/question/14937026
#SPJ4
the following data are obtained when open-circuit and short-circuit tests are performed on a single-phase, 50-kva, 2400/240-volt, 60-hz distribution transformer.
With relatively little power given to the transformer and winding currents of the same size as during operation, a short-circuit test is performed to determine the transformer impedance and losses.
What is open-circuit test on a single phase transformer?One approach used in electrical engineering to ascertain the no-load impedance of a transformer's excitation branch is the open-circuit test, also known as the no-load test. The open circuit, which is shown on the right side of the picture as the "hole" or incomplete component of the circuit, is a representation of the no load.Impedance series is neglected:E1 = N1/N2 = E2=N1/N2 V2 = (2400/240) 240<° = 2400<0°V
N2 / N1 I 2 = 240 / 2400(4.85) = 0.485A
GC = P2 / E1 ² = 173 / (2400)² = 3.003 × (10 )-5 S.
YC = (N2 / N1 I2)/E1 = 0.485 /2400 = 2.021 × (10-)4S
BM = √Y²C - G²C = √(2.021 ×( 10)-4)² - (3.003 × (10)-5 )² = 1.998 × (10 )-4 S
YC = GC - JBM = 3.003 × (10) -5 - j1.998 × (10)-4 S
= 2.021 × (10) -4 < -81.45°S.
To Learn more About short-circuit test refer to:
https://brainly.com/question/27809868
#SPJ4
stress concentration does have effects on brittle materials on their behavior even under static loads. however, the geometric stress concentration is often ignored for cast-brittle materials, such as cast iron. why? choose the best answer.
Because local yielding or deformation occurs in ductile materials and thus reduces the concentration, stress concentration in ductile materials is not as severe as it is in brittle materials.
In the part design, a stress concentration is a location where the stress is much higher than it is elsewhere. The geometry of the part's sharp corners, holes, notches, or grooves is what most frequently causes stress concentrations. In order to ensure the component functions properly and safely, it is crucial to analyze it for stress concentration. The system's balance may be further hampered and serious repercussions may result if the fabricated or produced component is not entirely functioning under stress. The term "stress concentration" refers to a location that exhibits an abrupt geometric transition or discontinuity and is characterized by high localized stress relative to the body's average stress.
Learn more about concentration here:
https://brainly.com/question/13441104
#SPJ4
Wherever possible, you should write automated tests. The tests are embedded in a program
that can be run every time a change is made to a system.
Software testing is a step in the software development process. To tell stakeholders about the software's quality, an investigation is conducted against the product.
What happens during the software testing process?Software testing is the procedure used to assess and confirm that a software program or application performs as intended. Bugs can be avoided, development expenses are decreased, and performance is increased.Stakeholders in testing include senior management, program and project managers, Scrum masters, developers, engineers, and architects, as well as specialists in operations, product ownership, and business analysis. Testers, however, should put the consumer first.An expert testing team carries out this kind of testing. The software development life cycle's initial stage, system testing, involves comprehensive testing of the entire application. To ensure that the application satisfies the functional and technological requirements, it is rigorously tested.To learn more about Stakeholders refer to:
https://brainly.com/question/15532995
#SPJ4
a data analyst inputs the following code in rstudio: change 1 <- 70 which of the following types of operators does the analyst use in the code? a. arithmetic b. assignment c. logical d. relational
An operator or concept used in programming that evaluates or defines a relationship between two entities is known as a relational operator. Equalities and inequalities in numbers are among them.
What does the C relational operator mean?An operator that examines relationships between operands does so. It yields a value of 1 if the relationship is true and a value of 0 if the relationship is false. Relational operators are employed in loops and decision-making.Two of the available values are compared using relational operators to determine the relationship between the two value pairs. Like equal to, better than, worse than, etc. The complete list of relational operators in the C language is as follows: the same.An operator or concept used in programming that evaluates or defines a relationship between two entities is known as a relational operator. Equalities and inequalities in numbers are among them.To learn more about Relational operators refer to:
https://brainly.com/question/28039937
#SPJ4
a data flow diagram (dfd) shows _____.
A data flow diagram (DFD) shows how a system transforms input data into useful information.
What is data?In Computer technology, data simply refers to any representation of factual instructions or information in a formalized and structured manner, especially as a series of binary digits (bits), symbols, characters, quantities, or strings that are used on computer systems in a company.
What is a data flow diagram (DFD)?A data flow diagram (DFD) can be defined as a type of chart that is designed and developed to illustrate how information is moved and transformed in a computer system or process.
This ultimately implies that, a data flow diagram (DFD) can be used to show data inputs, data outputs, storage locations, and all of the routes that are required.
Read more on data here: brainly.com/question/26207955
#SPJ1
What is not one of the 3-stage parametric equalizer adjustments on a yaesu ft-dx10?.
The 3-stage parametric equalizer adjustments on a Yaesu FT-DX10 are high frequency, middle frequency, and low frequency.
What is parametric equalizer?
This illustration demonstrates how to create parametric equalizer filters. Digital filters known as parametric equalisers are used in audio to modify the frequency content of a sound input. By permitting adjustments to the gain, centre frequency, and bandwidth of each filter, parametric equalisers offer capabilities beyond those of graphic equalisers. Graphic equalisers, on the other hand, only let you change the gain of the each filter. Typically, second-order IIR filters are used to create parametric equalisers. These filters have the issue of having relatively wide ripple or transition areas due to their low order, and when multiple of them are combined in a cascade, they may overlap. The ability to create high-order IIR parametric equalisers is provided by Audio ToolboxTM. Such high-order designs provide each filter's shape much greater flexibility.
To learn more about parametric equalizer
https://brainly.com/question/27950429
#SPJ4
what are the reasons why fine grained of alkali igneous rocks can not be used in cement
Fine grained of alkali igneous rocks cannot be used in cement because of the volume expansion caused by the Alkali-silica reaction, fine-grained igneous rocks cannot be used as aggregates in cement.
What does fine grained mean in an igneous rock?Extrusive igneous rocks have a fine-grained or aphanitic texture, with grains that are too small to see without a magnifying glass. The fine-grained texture suggests that the rapidly cooling lava did not have enough time to form large crystals. A petrographic microscope can be used to examine these tiny crystals.
The texture of an igneous rock (fine-grained vs coarse-grained) is determined by the rate at which the melt cools: slow cooling produces large crystals, while fast cooling produces small crystals.
The chemical reaction that occurs in both alkali cations and hydroxyl ions in the pore solution of hydrated cement paste and certain reactive silica phases present in concrete aggregates is known as the alkali-silica reaction (ASR).
Learn more about cement on:
https://brainly.com/question/14323034
#SPJ1
Mark all the correct operation/s that first, rotate x with p. Then, rotate x with g
p - parent
g - grandparent
x - node
let p and g be respectively the parent and grand parent of x. p is the root. Make x the new root by rotating edge(x,p).The Zig_Zig case p is the left child of g and X is the right child of p,making g the new parent of x rotating edge(x,g).
What exactly is zig-zig rotation?Every node in zig rotation shifts one position to the right of where it currently is. When the item to be searched is either a root node or a left child of a root node, Zig rotation is used.Zig does not allow null or 0 as a value for normal pointers. Where T is the child type, they use the syntax *T. Dereferencing is accomplished using variable, and referencing is accomplished using &variable.A particular kind of binary search tree is the splay tree. The splay tree is not necessarily balanced, unlike other versions like the AVL tree, the red-black tree, or the scapegoat tree.To learn more about zig rotation refer to:
https://brainly.com/question/24522433
#SPJ4
Suppose that a digitized colour TV picture is to be transmitted from a source that uses a matrix of 800 X 600 picture elements (pixels), where each pixel can take on one of 256 intensity values. Assume that 28 frames are sent per second? Compute the source rate R (bps)? (Hint: Check the basic colour combination in a colour picture)
Answer:
Example problem
Explanation:
(a) The source rate can be calculated as the product of the picture sample size and number of pixel per sample size.
Given:
Picture sample size = 480 * 500. The number of pictures sent per second = 30.
Hence sample size = 480 * 500 * 30 = 7.2e6.
Since each pixel (sample) can take one of 32 values (voltage levels), hence it needs
l
o
g
2
32
=
l
o
g
2
2
5
=
5
∗
l
o
g
2
2
=
5
∗
1
=
5
bits/pixel (bits/sample).
The source rate R is (bps) = 7.26 * 5 = 36e6 bps.
identify the variables identified by ginnett that are essential to the effective functioning of teams.
Two essential elements of effective teamwork that raise job satisfaction are open communication and mutual support.
What defines effective teamwork?Trust, open communication, and effective leadership are essential for effective teamwork, as well as a focus on shared objectives and shared accountability for success (or failure). But without respect and openness, the team Open communication and mutual support are two crucial components of successful teamwork that increase job happiness. will struggle to do tasks properly. Owning your obligations, maintaining accountability, and following through on your commitments are necessary for effective teamwork. Because team members depend on one another, if one individual falters, the entire project could be derailed. The team's members must have a good working relationship and mutual trust.To learn more about effective teamwork refer to:
https://brainly.com/question/3813692
#SPJ4
(pattern recognition: consecutive four equal numbers) rewrite the isconsecutivefour function in programming exercise 8.21 using a vector as follows: bool isconsecutivefour(const vector>
Using the knowledge in computational language in C++ it is possible to write a code that isconsecutivefour function in programming
Writting the code:
#include <iostream>
using namespace std;
#include<vector>
bool isconsecutivefour( const vector<vector<int>> &values)
{
int res=0;
//checking if the vector has consecutive fours row-wise
for(int i=0;i<values.size();i++)
{
for(int j=0;j<values[i].size()-3;j++)
{
//if a consecutive four is obtained
if(values[i][j]==values[i][j+1] and values[i][j+1]==values[i][j+2] and values[i][j+2]==values[i][j+3])
{
res=1;
break;
}
}// we break the outer loop if a consecutive four is found
if(res==1){
break;}
}
//if a consecutive four is obtained 1 is returned
if(res==1)
return 1;
for(int i=0;i<values[0].size();i++)
{
int j;
for( j=0;j<values.size()-3;j++)
{
//if a consecutive four is obtained
if(values[j][i]==values[j+1][i] and values[j+1][i]==values[j+2][i] and values[j+2][i]==values[j+3][i])
{
res=1;
break;
}
}// we break the outer loop if a consecutive four is found
if(res==1){
break;}
}
if(res==1)
return 1; //if a consecutive four is obtained 1 is returned
else
return 0; //if a consecutive four is not obtained 0 is returned
}
int main() {
int r,c;
//input number of row
cout<<"Enter row size : " ;
cin>>r;
cout<<endl;
//input number of columns
cout<<"Enter column size : ";
cin>>c;
cout<<endl;
vector<vector<int>> values(r,vector<int>(c,0));
cout<<"Enter the values :"<<endl;
int x;
for(int i=0;i<r;i++)
{
for(int j=0;j<c;j++)
{
cin>>x;
values[i][j]=x;
}
}
bool res;
res=isconsecutivefour(values);
if(res==1) // if a consecutive four is found
cout<<"The array has consectutive fours"<<endl;
else //consecutive four is not found if 0 is returned
cout<<"The array does not have consectutive fours"<<endl;
See more about C++ at brainly.com/question/12975450
#SPJ1
BAND SAW SAFETY TEST PART 2,
The completed sentences with respect to carpentry tools are given as follows:
Use only a sharp blade with a proper set.When the blade is properly installed the teeth should point down.The blade should be adjusted so it runs 1/32 of an inch from the blade support wheel;Keep your hand at least two inches from the blade.Use a band saw when sawing small stock/pieces.Adjust the upper guide about 1/8 to 1/4 inches above the material being cut.Properly adjust the band saw blade so it will run on the center of the wheels.Move the upper guide only while the saw is stopped.The smallest radius that can be safely cut with a 1/2 inch wide blade is 1, 1/4 inchesA dull or improperly set blade will cause the blade to lean to one side on the workpiece.The name of the add-on tool we use to rip wood on the band saw is called a table saw.When you cross or cut angles on the band saw you use a Crosscut sled or cross-cut saw.What is the benefit of knowing the right carpentry tool to use?Because each instrument is precisely built for a specific function, selecting the appropriate tool will also reduce the amount of effort necessary to do a job correctly without causing harm to either the machinery or the material being worked on.
Many construction mishaps can be avoided by planning ahead of time.
Learn more about table saw:
https://brainly.com/question/28896152
#SPJ1
technician a states that disc brake rotors can be of the hub-style. technician b states that disc brake rotors can be of the hubless-style. who is correct?
Both Technicians A and B are accurate when they say that disc brake rotors can be either hub-style or hubless-style.
With disc brakes, the brake pads attached to the brake callipers grip on the rotating braking rotors to stop or slow down the wheels. Friction is created by the brake pads pressing against the rotors, which turns kinetic energy into heat energy.
Although this thermal energy produces heat, it may be effectively dispersed since the primary components are exposed to the environment. This ability to dissipate heat lessens brake fade, a condition where heat affects how well a vehicle brakes. The resistance of disc brakes to water fade, which happens when water on the brakes considerably lowers braking force, is another benefit. The rotor spins rapidly as the car is moving, and this rotational motion discharges the water from the rotors themselves, resulting in stable braking force.
Learn more about Rotors here:
https://brainly.com/question/18650040
#SPJ4
D
Question 7
Commercial photographers attempt to produce images that will blend in and make little impact on
the public.
O True
False
1 pts
A
False. Commercial photographers attempt to produce images that will stand out and make a big impact on the public.
What is photographers?
A photographer often works as a freelancer, getting hired by different customers for specialised tasks. A client who hires a part-time or freelance photographer is expected to adhere to their every demand, as well as to put up a business strategy that makes options and price readily visible and understandable.
Photographers are in charge of the digital and physical development of their photos, as well as any or all editing that may be necessary. Simple cropping, adding/changing colours and shading, modifying sharpness and lighting, or deleting things to tidy up the image are all examples of editing techniques.
To learn more about photographers
https://brainly.com/question/28081565
#SPJ1
1) (5 pts) (abet: 2) given the dfa below, give a regular expression that describes the language that it recognizes.
2((0+1)(0+1)*2+2)* is a regular expression that describes the language that it recognizes.
What is a regular expression?
A regular expression is a string of characters that specifies a text search pattern. String-searching algorithms typically use such patterns for "find" or "find and replace" operations on strings, as well as input validation. In theoretical computer science and formal language theory, regular expression techniques are developed.
SA=\epsilon (Eqaution 1)
SB=SB(0)+SB(1)+SB(2) + SA(0) + SA(1) (Eqaution 2)
SC=SA(2)+SD(2)+SC(2) (Eqaution 3)
SD=SC(0+1) + SD(0+1) (Eqaution 4)
Using arden's expression on equation 5 we can write it as:
SD=SC(0+1)(0+1)* (Equation 5)
We need to find SC to get the regular expression as it is the final state.
We substitute equations into one another to get the answers.
Substituting Equation 1 to equation 3 we get:
SC=\epsilon(2) + SD(2) + SC(2)
SC = (2+SD(2)) + SC(2)
Substituting Equation 5 into it we get:
SC=2+SC(0+1)(0+1)*2+SC(2)
SC=2+SC((0+1)(0+1)*2+2)
Using arden's therorem we can write it as:
SC=2((0+1)(0+1)*2+2)*
Hence 2((0+1)(0+1)*2+2)* is the regular expression that this DFA recongnizes.
To learn more about regular expression
https://brainly.com/question/14469911
#SPJ4
if the mercury in a manometer raises 13.5 millimeters due to a change in pressure, what is the corresponding change in pressure in atm?
The mercury in a manometer raises 13.5 millimeters due to a change in pressure the corresponding pressure is 0.0178 atm.
What is manometer?Manometer is defined as an instrument for measuring the pressure acting on a column of fluid that consists of a U-shaped liquid tube in which the liquid rises to various heights in the two arms due to different pressures acting in the two arms of the tube.
We know that
1 atm = 760 mmHg
So, X atm = 13.5 mmHg
X x 760 = 13.5 x 1
X = 13.5 / 760
X = 0.178 atm
Thus, the mercury in a manometer raises 13.5 millimeters due to a change in pressure the corresponding pressure is 0.0178 atm.
To learn more about manometer, refer to the link below:
https://brainly.com/question/15009345
#SPJ1
Assuming a 1-KB page size, what are the page numbers and offsets for the following address references (provided as decimal numbers)? a. 21205 b. 164250
The page numbers and offsets of the following address reference are 1663 and 6595 respectively.
Given,
Page size= 1 (*KB) = 2n = 1024 = 210
So, the value of bits of offest part is n = 10
a. 21205
Binary Format = 101001011010101
This binary address is split into 2 parts, first is page no. and other part is page offset
Page no. : 01010010 = 82 (in decimal)
Page offset : 11010101 = 213 (in decimal)
b. 164250
Binary Format = 00101000000110011010
Page no. : 0010100000 = 160 (in decimal)
Page offset : 0110011010 = 410 (in decimal)
c. 121357
Binary Format = 00011101101000001101
Page no. : 0001110110 = 118 (in decimal)
Page offset : 1000001101 = 525 (in decimal)
d. 16479315
Binary Format = 111110110111010001010011
Page no. : 111110110111 = 4023( in decimal)
Page offset : 010001010011 = 1107 (in decimal)
e. 27253187
Binary Format = 0001100111111101100111000011
Page no. : 00011001111111 = 1663(in decimal)
Page offset : 01100111000011 = 6595 ( in decimal)
To learn more about Binary, visit: https://brainly.com/question/14914277
#SPJ4