The plane of a rectangular coil of dimension 5 cm by 8 cm is perpendicular to the direction of a magnetic field B. The coil has 147 turns and a total resistance of 12.7 .
At what rate must the magnitude of B change in order to induce a current of 0.392 A in the windings of the coil?
Answer in units of T/s.

The position of the center of mass of a system of particles can be expressed as a function of time. The correct answer is O 44 m/s.

In this case, the equation is x = 4.5 + 2.4t + 2t^2 + 1.1t^3, where x is in meters and t is in seconds. Since the system starts from rest at t=0, its initial velocity is zero.

To find its velocity at 3.0 seconds, we need to take the derivative of the position function with respect to time. The derivative of x with respect to t is v = 2.4 + 4t + 3.3t^2. Plugging in t = 3.0, we get v = 2.4 + 4(3.0) + 3.3(3.0)^2 = 44 m/s. Therefore, the answer is O 44 m/s.

To know more about center of mass refer here:

https://brainly.com/question/28996108#

#SPJ11

The acceleration of the electron is (e) into the page. This is because when a charged particle moves through a magnetic field at a perpendicular angle, it experiences a force perpendicular to both the direction of motion and the magnetic field direction. In this case, the electron is moving to the right in the plane of the page while the magnetic field is going into the page. Therefore, the force experienced by the electron is directed into the page, causing it to accelerate in that direction.
Hi! When an electron moves at a constant speed in the plane of the page and enters a magnetic field going into the page, the acceleration of the electron is (a) upward, due to the interaction between its charge and the magnetic field according to the Lorentz force.

a. The work done by the force is 32.436 J.

b. The change in potential energy is: ΔU = -32.436 J

c. The particle’s initial kinetic energy at x1 if its final speed at x2 is 10.5 m/s is 126.20 J.

a. To calculate the work done by the conservative force, we need to integrate the force over the distance moved by the particle. The work done by the force F(x) from x1 to x2 is given by:

W = ∫x1x2 F(x) dx

Since the force is conservative, we can write it as the gradient of a potential energy function U(x):

F(x) = - dU(x) / dx

Therefore, we can write:

W = -∫x1x2 dU(x)

Integrating this expression gives:

W = U(x1) - U(x2)

To calculate the potential energy at each position, we use the formula for the potential energy of a conservative force:

U(x) = - ∫∞x F(x') dx'

Substituting the given force, we get:

U(x) = - ∫∞x (bx' + a) dx' = - [0.5 b x'^2 + a x']∞x

Therefore, the potential energy at x1 and x2 are:

U(x1) = - [0.5 b x1^2 + a x1] = -32.328 J

U(x2) = - [0.5 b x2^2 + a x2] = -64.764 J

Thus, the work done by the force is:

W = U(x1) - U(x2) = 32.436 J

Therefore, the work done by the force is 32.436 J.

b. The change in potential energy of the particle between x1 and x2 is given by:

ΔU = U(x2) - U(x1) = - (U(x1) - U(x2)) = -W

Therefore, the change in potential energy is:

ΔU = -32.436 J

c. The work done by the force is equal to the change in the total energy of the particle, which is the sum of its kinetic energy and potential energy:

W = ΔK + ΔU

Since the force is conservative, the work done is converted into potential energy, so ΔK = 0.

Therefore, we have:

W = ΔU = -32.436 J

We can use the work-energy principle to relate the work done by the force to the change in kinetic energy of the particle:

W = ΔK = (1/2) m (v2^2 - v1^2)

where m is the mass of the particle, v1 is the initial velocity at x1, and v2 is the final velocity at x2.

We know that m = 6.86 kg, v2 = 10.5 m/s, x1 = 1.6 m, and x2 = 3.7 m. Therefore, we can solve for v1:

-32.436 J = (1/2) (6.86 kg) (10.5 m/s)^2 - (1/2) (6.86 kg) v1^2

Solving for v1, we get:

v1 = 6.08 m/s

Therefore, the initial kinetic energy of the particle at x1 is:

K1 = (1/2) m v1^2 = 126.20 J

Thus, the particle’s initial kinetic energy at x1 is 126.20 J.

For more such questions on Work done.

https://brainly.com/question/13286869#

#SPJ11

For the space curve r(t)=(cost+tsint)i+(sint−tcost)j+2k,

Tangent vector T: T = (cos(t) + tsin(t))i + (sin(t) - tcos(t))j + 2k

Normal vector N: N = -sin(t)i + (-cos(t))j

Curvature K: K = 1/t

The given space curve r(t) is defined by three components: x = cos(t) + tsin(t), y = sin(t) - tcos(t), and z = 2. To find the tangent vector T, we differentiate each component of r(t) with respect to t, resulting in T = (cos(t) + tsin(t))i + (sin(t) - tcos(t))j + 2k. The tangent vector T represents the direction of motion of the curve at any given point.

The normal vector N is found by taking the derivative of T with respect to t, which gives N = -sin(t)i + (-cos(t))j. The normal vector N is perpendicular to the tangent vector T and represents the direction of the curvature of the curve.

The curvature K is given by K = 1/t, where t is the parameter of the curve. The curvature measures how much the curve deviates from a straight line at a particular point. In this case, the curvature is inversely proportional to the parameter t, which means that the curvature decreases as t increases.

For more questions like Vector click the link below:

https://brainly.com/question/29740341

#SPJ11

The magnitude of the torque on the current-carrying square wire in the uniform magnetic field is 0.0027 Nm.

1. The wire forms a square loop, and each side has a length of 6 cm or 0.06 m.
2. The current flowing through the wire is 2.5 A.
3. The magnetic field strength is 0.3 T and is in the z direction.

To find the torque, we can use the formula:

Torque = μ × B × sinθ

where μ is the magnetic moment, B is the magnetic field strength, and θ is the angle between the magnetic moment and the magnetic field.

Since the magnetic moment μ = NI × A, where N is the number of turns (1 in this case), I is the current, and A is the area of the loop:

μ = 1 × 2.5 A × (0.06 m × 0.06 m) = 0.009 Nm/T

Now, since the magnetic field is in the z direction and the loop is in the xy plane, the angle θ between the magnetic moment and the magnetic field is 90 degrees. Therefore, sinθ = 1.

Finally, calculating the torque:

Torque = 0.009 Nm/T × 0.3 T × 1 = 0.0027 Nm

In a homogeneous magnetic field, a square wire carrying current experiences a torque of 0.0027 Nm.

Learn more about "torque": https://brainly.com/question/17512177

#SPJ11

The speed of light inside the plastic is approximately 2.00 x [tex]10^8[/tex]  m/s.

To find the speed of light inside the plastic, we can use Snell's Law, which relates the angle of incidence and angle of refraction of a light ray to the indices of refraction of the two media through which the light is passing:

[tex]n_1[/tex] × sin(θ1) = [tex]n_2[/tex] × sin(θ2)

where n1 and [tex]n_2[/tex] are the indices of refraction of the two media, and θ1 and θ2 are the angles of incidence and refraction, respectively.

In this case, the light is passing from air (with an index of refraction of approximately 1.00) into a block of plastic. We are given that the angle of incidence is 36.8 degrees and the angle of refraction is 22.9 degrees. We can therefore use Snell's Law to solve for the index of refraction of the plastic:

1.00 ×sin(36.8) = [tex]n_2[/tex] × sin(22.9)

[tex]n_2[/tex] = 1.50

This tells us that the index of refraction of the plastic is 1.50. We can then use the relationship between the speed of light and the index of refraction:

v = c/n

where v is the speed of light in the plastic, c is the speed of light in a vacuum (approximately 3.00 x [tex]10^8[/tex] m/s), and n is the index of refraction of the plastic. Plugging in the values we have:

v = (3.00 x [tex]10^8[/tex]m/s) / 1.50

v = 2.00 x [tex]10^8[/tex] m/s

Therefore, the speed of light inside the plastic is approximately 2.00 x [tex]10^8[/tex]  m/s.

To know more about speed of light refer here :

https://brainly.com/question/29798767

#SPJ11

The tension in the cable is 270.25 N.

To find the tension in the cable used to raise a 25 kg urn from an underwater archaeological site at a constant speed, with a 25 N drag force from the water, you can follow these steps,

1. Calculate the gravitational force acting on the urn: F_gravity = mass × acceleration due to gravity, where mass = 25 kg and acceleration due to gravity (g) = 9.81 m/s^2.
  F_gravity = 25 kg × 9.81 m/s^2 = 245.25 N

2. Since the urn is raised at a constant speed, the net force acting on it is zero. Therefore, the tension in the cable must balance the gravitational force and the drag force.
  Tension = F_gravity + Drag force

3. Plug in the values for the gravitational force and the drag force:
  Tension = 245.25 N + 25 N = 270.25 N

Therefore, the cable is under 270.25 N of tension.

Learn more about "tension": https://brainly.com/question/24994188

#SPJ11

The entropy change is positive and proportional to the number of moles of gas and the natural logarithm of 2 and  the entropy of mixing is given by ΔS = -R(nAfa ln fa + nBfb ln fb).

The change in entropy when the partition is removed and the gases mix can be calculated using the formula:

ΔS = -R[na(fA ln fA + (1-fA) ln (1-fA)) + ng(fB ln fB + (1-fB) ln (1-fB))]

where R is the gas constant, na and ng are the number of moles of gases A and B, respectively, and fA and fB are the fractions of the container that they occupy before mixing.

The formula for entropy change is based on the idea that the number of ways in which the molecules can be arranged in the combined volume is greater than the number of ways in which they could be arranged if they were separated into two volumes. This increase in the number of possible microstates leads to an increase in entropy.

The first term in the equation represents the contribution of gas A to the entropy change, while the second term represents the contribution of gas B. The logarithmic terms arise from the fact that the number of microstates is proportional to the natural logarithm of the number of ways in which the molecules can be arranged.

In the case where the two gases are identical (i.e., na = ng and fA = fB), the entropy change simplifies to:

ΔS = R[na ln 2]

This result shows that the entropy change is positive and proportional to the number of moles of gas and the natural logarithm of 2.

Learn more about change in entropy

brainly.com/question/30691597

#SPJ11

Using Snell's law From straight above the coin looks to be 2.08 feet below the surface of the water.

The link between the refractive indices of the two contacting substances and the route a light ray takes as it crosses a boundary or surface of separation between them is known as Snell's law in optics. This law was created in 1621 by Dutch astronomer and mathematician Willebrord Snell. (also known as Snellius).

Let x be the distance between the surface of the water and the coin. Then, the angle of incidence is arcsin(x/6.2), and the angle of refraction is arcsin((x/1.33)/6.2).

Using Snell's law, we can equate the two angles:

sin(arcsin(x/6.2)) = sin(arcsin((x/1.33)/6.2))

x/6.2 = (x/1.33)/6.2

x = (x/1.33)

x = 2.08 feet

To know more about Snell's law visit:-

https://brainly.com/question/2273464

#SPJ1

Te electric field inside the wire is 9.375 V/m. The diameter of the wire is 0.518 mm

Part A: To find the electric field inside the wire, we need to use Ohm's law, which relates the electric field (E), current (I), and resistance (R) of the wire. The resistance of the wire can be calculated using the formula:

[tex]R = ρ * L / A[/tex]

where ρ is the resistivity of nichrome, L is the length of the wire, and A is the cross-sectional area of the wire. The resistivity of nichrome at room temperature is approximately 1.1 x 10[tex]^-6[/tex] Ωm.

Since the wire is connected across the terminals of a 1.5 V battery, the potential difference across the wire is 1.5 V. Using Ohm's law, we can calculate the current in the wire:

I = V / R

where V is the potential difference and R is the resistance. Substituting the values, we get:

I = 1.5 V [tex]/ (ρ * L / A)[/tex]

Solving for ρ * L / A, we get:

ρ * L / A = 1.5 V / I

Substituting the values of ρ, L, and I, we get:

[tex]ρ *[/tex]0.16 m / A = 1.5 V / 1.2 A

Solving for ρ * 0.16 m / A, we get:

ρ * 0.16 m / A = 1.25 Ω

Substituting the value of ρ * L / A in the resistance formula, we get:

R = 1.25 Ω

Now we can use Ohm's law to find the electric field inside the wire:

E = V / L

where V is the potential difference and L is the length of the wire. Substituting the values, we get:

E = 1.5 V / 0.16 m

Solving for E, we get:

E = 9.375 V/m

Therefore, the electric field inside the wire is 9.375 V/m.

Part B: The current density (J) inside the wire is defined as the current per unit cross-sectional area:

J = I / A

where I is the current in the wire and A is the cross-sectional area of the wire. Substituting the values, we get:

J = 1.2 A / ([tex]π/4 * d^2[/tex])

where d is the diameter of the wire. Solving for d, we get:

d = [tex]√(4 * I / (π * J))[/tex]

Substituting the values of I and J, we get:

d = [tex]√(4 * 1.2 A / (π * (1.2 A / (π * (0.008 m)^2)))[/tex])

Solving for d, we get:

d = 0.518 mm

Therefore, the diameter of the wire is 0.518 mm.

Part C: We have already calculated the diameter of the wire in Part B, which is 0.518 mm.

learn more abouT electric field here:

https://brainly.com/question/14372859

#SPJ4

Before the switch is changed (t < 0), the circuit is in steady-state conditions. This means that the voltage across the inductor is equal to 0 since there is no change in current flowing through the inductor.

Just after the switch is changed, the circuit is no longer in steady-state conditions. The current through the inductor cannot change instantaneously, so it will continue to flow in the same direction as before the switch was changed. However, the voltage across the inductor will change as the current continues to flow through it.

To determine the voltage across the inductor just after the switch is changed, we need to use the equation V = L(di/dt), where V is the voltage across the inductor, L is the inductance, and di/dt is the rate of change of current flowing through the inductor.

At t = 0+, just after the switch is changed, the current flowing through the inductor is the same as it was just before the switch was changed, since it cannot change instantaneously. Therefore, di/dt = 0.

Using the given values, we can calculate the voltage across the inductor just after the switch is changed as follows:

V = L(di/dt) = 0.1 H * 0 A/s = 0 V

So the voltage across the inductor just after the switch is changed is 0 V.

To know more about steady-state conditions click here:

https://brainly.com/question/1900452

#SPJ11

The voltage across the inductor just before the switch is changed is 12 volts, and just after the switch is changed, it becomes 0 volts.

V_L = L * di/dt = L * d/dt(-Vs / (R + Rs))

   = -L * Vs / (R + Rs) * d/dt(1)

   = 0

Voltage, also known as electric potential difference, is a measure of the electric potential energy per unit charge between two points in an electric circuit. It is denoted by the symbol V and is measured in volts (V).

Voltage represents the amount of work needed to move a unit charge from one point to another in an electric field. The greater the voltage, the more energy is required to move the charge. Voltage is a fundamental concept in electrical engineering and is used to describe the behavior of electrical circuits, including the flow of current and the power consumed by devices. Voltage can be created by a variety of sources, including batteries, generators, and power supplies.

To learn more about Voltage visit here:

brainly.com/question/2364325

#SPJ4

The relative speed of the two parts separating is 0.207 m/s.

To find the relative speed, we first calculate the final velocities of both parts using the impulse-momentum theorem. Impulse equals the change in momentum (mass × change in velocity). For each part:

1. For the 1370 kg part:
Impulse = mass × change in velocity
490 N·s = 1370 kg × change in velocity
Change in velocity = 0.357 m/s

2. For the 1110 kg part:
Impulse = mass × change in velocity
490 N·s = 1110 kg × change in velocity
Change in velocity = 0.441 m/s

Finally, subtract the smaller velocity from the larger one to find the relative speed:
Relative speed = 0.441 m/s - 0.357 m/s = 0.207 m/s

To know more about impulse-momentum theorem click on below link:

https://brainly.com/question/14121529#

#SPJ11

The two primary types of celestial bodies in our solar system are comets and asteroids.

Comets are composed of rock, dust, and ice, whereas asteroids are typically made of rock and metal. The asteroid belt between Mars and Jupiter contains asteroids, which are horribly formed objects.

The Kuiper Belt and the Oort Cloud are just two places where comets can be discovered. Comets, on the other hand, can be either spherical or oblong in shape.

Ion and dust tails are both visible on comets. These heavenly bodies can have a wide variety of temperatures and orbit the sun in an elliptical way.

Learn more about comets:

https://brainly.com/question/28543341

#SPJ4

a. Mn^2+ (aq) -> Mn^4+ (aq) + 2e^-,  b. 2I^- (aq) + 2e^- -> I2 (s), c. Mn^2+ (aq) + 2I^- (aq) -> Mn^4+ (aq) + I2 (s).

Involving direct current, manganese, and manganese(II) iodide.

a. The oxidation half-reaction involves the loss of electrons by the manganese(II) ion. The balanced equation for the oxidation half-reaction is:

Mn^2+ (aq) -> Mn^4+ (aq) + 2e^-

b. The reduction half-reaction involves the gain of electrons by the iodide ions. The balanced equation for the reduction half-reaction is:

2I^- (aq) + 2e^- -> I2 (s)

c. To obtain the balanced equation for the overall reaction, combine the oxidation and reduction half-reactions:

Mn^2+ (aq) + 2I^- (aq) -> Mn^4+ (aq) + I2 (s)

So, when a direct current is applied to a solution of manganese(II) iodide, the Mn^2+ ions are oxidized to Mn^4+ ions, and the I^- ions are reduced to form solid iodine (I2).

Learn more about redox reaction here: brainly.com/question/13293425

#SPJ11

The magnitude of the magnetic force on the wire if the angle between the magnetic field is 2.474 N

To calculate the magnitude of the magnetic force on the wire, you can use the formula:
F = I * L * B * sin(θ)
Where F is the magnetic force, I is the current (5.1 A), L is the length of the wire (1.6 m), B is the magnitude of the magnetic field (0.76 T), and θ is the angle between the magnetic field and the current (37°).
F = 5.1 A * 1.6 m * 0.76 T * sin(37°)
F ≈ 2.474 N
Magnetic force is the force exerted by a magnetic field on a moving electric charge. A magnetic field is a region in space where a magnetic force can be detected, and it is created by the movement of electric charges, such as the movement of electrons in a wire or the movement of the Earth's molten iron core.

To know more about force please refer: https://brainly.com/question/24115409

#SPJ11

The areas in between the runways now appear blue because they have been painted with a special type of paint

The areas in between the runways now appear blue because they have been painted with a special type of paint called runway safety area (RSA) markings.

These blue markings help pilots and airport personnel identify the areas where it is safe to operate aircraft, and also serve as a visual cue to indicate the boundary of the runway area.

The blue color is also easier to see in low light conditions or during inclement weather, which helps to enhance overall safety at the airport.

Learn more about runway safety

brainly.com/question/4543399

#SPJ11

The area of the circle is increasing at a rate of 176π m²/s when the radius is 8 m.

dA/dt = d/dt (πr²)

Using the chain rule, we get:

dA/dt = 2πr (dr/dt)

We know that dr/dt = 11 m/s (given in the problem statement) and we need to find dA/dt when r = 8 m.

Plugging in r = 8 m and dr/dt = 11 m/s, we get:

dA/dt = 2π(8)(11) = 176π

The chain rule is a fundamental concept in physics that describes how to calculate the derivative of a composite function. In physics, many quantities are related to each other through complex relationships, such as equations of motion or laws of conservation. The chain rule allows us to find the rate of change of one quantity with respect to another, even when the relationship between them is not simple or direct.

For example, in classical mechanics, the position, velocity, and acceleration of an object are related through differentiation. The chain rule enables us to calculate the acceleration of an object by taking the derivative of its velocity with respect to time and then multiplying it by the derivative of its position with respect to velocity.

To learn more about Chain rule visit here:

brainly.com/question/22882675

#SPJ4

We expect to find approximately 6 particles with an x-displacement of -20 um.

Based on the given probability distribution for displacements, we can calculate the expected number of particles with an x-displacement of -20 um as follows:

Probability of -20 um displacement = 0.06
Total number of particles = 100

Expected number of particles with -20 um displacement = Probability * Total number of particles
= 0.06 * 100
= 6 particles

So, we expect to find approximately 6 particles with an x-displacement of -20 um.

To learn more about probability, refer below:

https://brainly.com/question/30034780

#SPJ11

Answer:a. To find the potential difference between points A and B, we need to use the formula:

ΔV = W / q

where ΔV is the potential difference, W is the work done, and q is the charge.

Plugging in the given values, we get:

ΔV = 5 J / 0.25 C = 20 V

Therefore, the potential difference between points A and B is 20 volts.

b. The kinetic energy gained by a charged particle as it moves through a potential difference is given by:

KE = qΔV

where KE is the kinetic energy, q is the charge, and ΔV is the potential difference.

Assuming that the xenon ion is a singly ionized ion with a charge of +1.6 × 10^-19 C, we can calculate the kinetic energy gained in each case as:

Case 1: ΔV = 500 V, d = 0 (immediate)

KE = qΔV = (1.6 × 10^-19 C) × (500 V) = 8 × 10^-17 J

Case 2: ΔV = 500 V, d = 1 cm

The electric field between the two points is given by:

E = ΔV / d = 500 V / (0.01 m) = 5 × 10^4 V/m

The force on the ion is given by:

F = qE = (1.6 × 10^-19 C) × (5 × 10^4 V/m) = 8 × 10^-15 N

Using the work-energy theorem, we can calculate the distance traveled by the ion as:

W = Fd = KE

d = KE / F = (8 × 10^-17 J) / (8 × 10^-15 N) = 0.01 m

Therefore, the ion travels a distance of 1 cm before it comes to rest.

c. The electric field at the surface of the spherical shell is given by:

E = V / r

where V is the potential and r is the radius of the shell.

The dielectric strength of air is the maximum electric field that air can withstand before it breaks down and becomes conductive. In this case, the dielectric strength of air is 3 × 10^6 V/m.

Therefore, we can write:

E = 3 × 10^6 V/m

V / r = 3 × 10^6 V/m

Solving for r, we get:

r = V / E = (1 × 10^6 V) / (3 × 10^6 V/m) = 0.333 m

Therefore, the minimum radius of the spherical shell is 0.333 meters or 33.3 cm.

a. Therefore, the angular momentum of the fan at t = 3.0 s is 900 kg [tex]m^2/s.[/tex]

b. Therefore, the net torque on the fan at t = 3.0 s is 600 kg [tex]m^2/s^2.[/tex]

(a) The angular momentum (L) of the fan is given by:

L = Iω

I = moment of inertia and ω is the angular velocity.

Substituting the given values, we get:

L = [tex](2.5 kg m^2)(40 rad/s^3t^2) = 100t^2 kg m^2/s[/tex]

The angular momentum at t = 3.0 s, we simply substitute t = 3.0 s into the equation:

L = [tex]100(3.0 s)^2 kg m^2/s = 900 kg m^2/s[/tex]

(b) The net torque (τ) on the fan is given by:

τ = Iα

α is the angular acceleration.

Taking the derivative of the angular velocity with respect to time, we get:

α = dω/dt = 80 rad/s^3t

Substituting the given values, we get:

τ = [tex](2.5 kg m^2)(80 rad/s^3t) = 200t kg m^2/s^2[/tex]

To find the net torque at t = 3.0 s, we simply substitute t = 3.0 s into the equation:

τ = [tex]200(3.0 s) kg m^2/s^2 = 600 kg m^2/s^2[/tex]

Learn more about momentum visit: brainly.com/question/18798405

#SPJ4

The total resistance of twenty-one 215ω resistors connected in series is 4515ω. The resistance of twenty-one 215ω resistors connected in series can be calculated using the formula for resistors in series. The formula is:

Total Resistance (R_total) = R1 + R2 + ... + Rn

where R1, R2, ... Rn are the individual resistances of the resistors connected in series. In this case, there are twenty-one 215ω resistors connected in series, so we can write the formula as:

R_total = 215ω + 215ω + ... + 215ω (21 times)

To simplify the calculation, we can multiply the resistance of one resistor (215ω) by the total number of resistors (21):

R_total = 215ω × 21

Now, simply multiply the values:

R_total = 4515ω.

To know more about total resistance refer here:

https://brainly.com/question/16465349#

#SPJ11

In an RCL circuit, when a second capacitor is added in parallel to the capacitor already present, the resonant frequency decreases. This is because the resonant frequency is inversely proportional to the square root of the capacitance, and the equivalent capacitance increases when a second capacitor is added in parallel. So, the correct answer is option 2.

If the Resistor (R), Inductor (L), and Capacitor (C) are all connected in parallel with the AC current source, then we can say that circuit is a parallel RLC circuit. In this circuit, the voltage across each network element is the same, but only the supply current (AC) will get divided among the passive elements. Therefore the resonant frequency decreases because it is directly proportional to the capacitance, and the equivalent capacitance decreases when a second capacitor is added in parallel.

Learn more about resonant frequency: https://brainly.com/question/28381706

#SPJ11

a) The output RMS voltage, ΔV2rms, in a transformer is given by the ratio of the number of turns in the secondary coil to the number of turns in the primary coil, multiplied by the input RMS voltage[tex]ΔV2rms = N2/N1 x ΔV1rms[/tex].

b) Plugging in the values, [tex]ΔV2rms = 1650/110 x 34V = 510V[/tex].

A transformer is a device that is used to change the voltage of an alternating current (AC) by electromagnetic induction. It consists of two sets of coils, the primary and the secondary, which are wound around a common magnetic core. The voltage ratio of the transformer is given by the ratio of the number of turns in the secondary coil to the number of turns in the primary coil. If the input RMS voltage over the primary coil is given, the output RMS voltage over the secondary coil can be calculated using the voltage ratio. In this case, the output RMS voltage, ΔV2rms, is given by [tex]ΔV2rms = N2/N1 x ΔV1rms[/tex], where N1 is the number of turns in the primary coil, N2 is the number of turns in the secondary coil, and ΔV1rms is the input RMS voltage. Plugging in the given values, the numerical value of ΔV2rms is 510V.

Learn more about RMS voltage here:

https://brainly.com/question/28563538

#SPJ11

The value of t, which represents the time it takes for the father to give the merry-go-round an angular velocity of 1.50 rad/s, is 38.4 seconds.

What is Velocity?

Velocity is a vector quantity that describes the rate of change of an object's position with respect to time. It includes both magnitude (speed) and direction. Velocity is typically represented by a vector with an arrow pointing in the direction of motion, and its magnitude is given in units of distance per time (e.g., meters per second, kilometers per hour, etc.). In physics, velocity is an important concept used to describe the motion of objects and is often used in calculations involving displacement, acceleration, and other kinematic quantities.

Rotational inertia (I) = 6400 kg·m² (from the example problem)

Angular velocity (ω) = 1.50 rad/s

Torque (τ) = 250 N·m (from the example problem)

Plugging in the given values into the formula, we get:

t = 6400 kg·m² * 1.50 rad/s / 250 N·m

t = 38.4 s

Learn more about Velocity from the given link

https://brainly.com/question/24445340

#SPJ1

To compare current density J1 in segment 1 to current density J2 in segment 2, you need to determine the cross-sectional areas of both segments and then apply the formula for current density. The relationship between J1 and J2 will depend on the difference in cross-sectional areas of the segments.

To compare the current density (J1) in segment 1 to the current density (J2) in segment 2 when both segments of the wire are made of the same metal and current I1 flows into segment 1 from the left, follow these steps:

1. Understand that current density (J) is defined as the amount of current (I) flowing through a unit cross-sectional area (A) of a conductor, and it is given by the formula J = I / A.

2. Since both segments of the wire are made of the same metal, their electrical properties (such as resistivity) are the same.

3. Observe the cross-sectional areas (A1 and A2) of both segments. If the segments have the same cross-sectional area, then A1 = A2. If one segment has a larger cross-sectional area than the other, note the difference.

4. To compare the current densities, divide the current (I1) by the respective cross-sectional areas (A1 and A2) of each segment:
  J1 = I1 / A1
  J2 = I1 / A2

5. Compare J1 and J2 to determine their relationship. If A1 = A2, then J1 = J2. If A1 > A2, then J1 < J2. If A1 < A2, then J1 > J2.

To know more about "Density" refer here:

https://brainly.com/question/17226757?#

#SPJ11

AC power alternates polarity allowing reverse plug orientation, but DC power in batteries only flows in one direction, causing failure.

You can often reverse the plug in the wall because it is an AC. However, a battery is a DC.

When you plug a device into a wall outlet, it is using alternating current (AC) power is constantly changing polarity, which means that the voltage is constantly going from positive to negative and back again. This is why you can reverse the orientation of the plug without any problem, as the device will still be receiving power that alternates in both directions.

On the other hand, batteries are direct current (DC) power sources. DC power only flows in one direction, from the positive terminal to the negative terminal. If you put a battery in backward, the current will not flow through the device properly, and it will not work.

Therefore, the reason why you can often reverse the orientation of the plug with no problem is due to the nature of AC power, which constantly changes polarity. Conversely, the reason why you cannot put a battery in backward is because it is a DC power source, and the current only flows in one direction.

Learn more about AC AND DC power

brainly.com/question/30682622

#SPJ11

The object's angular velocity is not increasing at all, and remains constant. The torque acting on the object is 5.4 Newton meters (N/m).

The angular acceleration of the object can be found using the formula:

angular acceleration = (change in angular velocity) / time

In this case, the change in angular velocity is 3.0 rad/s per second, and we don't know the time. However, we can use another formula that relates angular acceleration, moment of inertia, and torque:

torque = moment of inertia x angular acceleration

Assuming there are no external torques acting on the object, we can set the torque to zero and solve for the angular acceleration:

angular acceleration = 0 / moment of inertia

Plugging in the given moment of inertia of 1.8 kg⋅m2, we get:

angular acceleration = 0 / 1.8 kg⋅m2 = 0 rad/s2

This means that the object's angular velocity is not increasing at all, and remains constant. If there were an external torque acting on the object, we would need to take that into account and use the first formula to find the angular acceleration.

Given that an object's moment of inertia (I) is 1.8 kg⋅m² and its angular acceleration (α) is 3.0 rad/s², we can find the torque (τ) acting on the object using the following formula:

τ = I × α

Identify the known values.
Moment of inertia, I = 1.8 kg⋅m²
Angular acceleration, α = 3.0 rad/s²

Apply the formula to find the torque.
τ = (1.8 kg⋅m²) × (3.0 rad/s²)

Calculate the torque.
τ = 5.4 N⋅m

So, the torque acting on the object is 5.4 Newton meters (N⋅m).

More on angular velocity: https://brainly.com/question/9612563

#SPJ11

a) The local heat transfer coefficient at a distance of 1.2 m from the leading edge is 91.4 W/m^2·K.

b) The total rate of heat transfer from the plate to the air is 1.38 kW.

a) To solve this problem, we need to use the equations for forced convection heat transfer from a flat plate. The local heat transfer coefficient at a distance of 1.2 m from the leading edge can be calculated using the following equation:

h(x) = 0.332 * (k / L) * (Re_x)^0.5 * (Pr)^n

where:

k = thermal conductivity of air = 0.026 W/m·K

L = length of plate = 2.0 m

Re_x = Reynolds number at distance x = (u * x) / ν, where ν is the kinematic viscosity of air = 1.5e-5 m^2/s

Pr = Prandtl number of air at 20°C = 0.72

n = exponent that depends on the flow regime (laminar or turbulent)

To determine the flow regime, we can calculate the Reynolds number at x = 1.2 m:

Re_1.2 = (3.8 m/s * 1.2 m) / 1.5e-5 m^2/s = 3.04e+5

This value is greater than the critical Reynolds number for laminar-turbulent transition, which is approximately 5e+5 for flow over a flat plate. Therefore, the flow is turbulent, and we can use n = 0.25 for this case.

Now we can plug in the values and solve for h(1.2):

h(1.2) = 0.332 * (0.026 W/m·K / 2.0 m) * (3.04e+5)^0.5 * (0.72)^0.25

= 91.4 W/m^2·K

Therefore, the local heat transfer coefficient at a distance of 1.2 m from the leading edge is 91.4 W/m^2·K.

b) To determine the total rate of heat transfer from the plate to the air, we can use the following equation:

q'' = h(x) * (T_s - T_inf)

where:

T_s = plate surface temperature = 150°C = 423 K

T_inf = air temperature far from the plate = 20°C = 293 K

The average heat transfer coefficient over the entire plate can be estimated as the average of the local values:

h_avg = (2/h(0) + 2/h(1.2))^-1 = (2/8.8 + 2/91.4)^-1 = 8.56 W/m^2·K

where h(0) is the local heat transfer coefficient at the leading edge, which we can assume to be zero.

Now we can use the average heat transfer coefficient to calculate the total rate of heat transfer:

q_total = h_avg * A * (T_s - T_inf)

where:

A = plate area = 2.0 m * 0.75 m = 1.5 m^2

q_total = 8.56 W/m^2·K * 1.5 m^2 * (423 K - 293 K)

= 1.38 kW

Therefore, the total rate of heat transfer from the plate to the air is 1.38 kW.

For more such questions on Heat transfer.

https://brainly.com/question/31462237#

#SPJ11