The arrival of small aircraft at a regional airport has a Poisson distribution with a rate of 2.3 per hour. a) Find the probability that there are no arrivals in a 20-minute interval. (10) b) Find the probability that there are at least two arrivals in a 30-minute interval. (10) c) Find the probability that there is at least one but no more than three arrivals in a 30-minute interval. (10) d) Find the expected number of arrivals during a 3-hour interval. (10)

The spacing between the two slits is approximately 0.1287 mm.

To find the spacing between the two slits, we can use the double-slit interference formula:

Fringe spacing (y) = (λ * L) / d

where λ is the wavelength of light (589 nm), L is the distance between the screen and the slits (110 cm), and d is the distance between the two slits. We are given y (5.0 mm) and need to find d.

First, let's convert the given units to meters:

λ = 589 nm = 589 * 10^-9 m
L = 110 cm = 1.1 m
y = 5.0 mm = 0.005 m

Now we can rearrange the formula to solve for d:

d = (λ * L) / y

d = (589 * 10^-9 m * 1.1 m) / 0.005 m
d ≈ 1.287 * 10^-4 m

To convert d to millimeters:

d ≈ 1.287 * 10^-4 m * 1000
d ≈ 0.1287 mm

So, the spacing between the two slits is approximately 0.1287 mm.

To learn more about wavelength, refer below:

https://brainly.com/question/4112024

#SPJ11

The magnitude of the electric field is 720 V/m, and its direction is negative x-direction.

The electric field is related to the potential difference by the following formula:

E = -(ΔV/Δx)

where ΔV is the potential difference and Δx is the distance between the two points.

In this case, the potential difference is:

ΔV = 1100 V - (-700 V) = 1800 V

The distance between the two points is:

Δx = 0.800 m - (-1.70 m) = 2.50 m

Therefore, the electric field is:

E = -(ΔV/Δx) = -1800 V / 2.50 m = -720 V/m

learn more abouT potential  here:

https://brainly.com/question/24142403

#SPJ4

Given:

Number of revolutions = 1000

Time taken for the revolutions = 50.7 ms = 0.0507 s

(a) The period (T) is the time taken for one revolution. We can calculate the period by dividing the time taken for the revolutions by the number of revolutions:

T = (time taken for revolutions) / (number of revolutions)

T = 0.0507 s / 1000 = 5.07 x 10^-5 s

Therefore, the period is 5.07 x 10^-5 seconds.

(b) The frequency (f) is the reciprocal of the period. We can calculate the frequency by taking the inverse of the period:

f = 1 / T

f = 1 / (5.07 x 10^-5 s) = 19,700 Hz (rounded to three significant figures)

Therefore, the frequency is 19,700 Hz.

(c) The angular frequency (ω) is the rate of change of the angle of rotation per unit time. We can calculate the angular frequency by first finding the angle of rotation in one revolution and dividing it by the time taken for one revolution:

Angle of rotation in one revolution = 2π radians (since one revolution is equivalent to 2π radians)

ω = (angle of rotation in one revolution) / (time taken for one revolution)

ω = 2π / (5.07 x 10^-5 s) = 1.24 x 10^5 rad/s (rounded to three significant figures)

Therefore, the angular frequency is 1.24 x 10^5 rad/s.

To know more about revolutions of jet engine :

https://brainly.com/question/16186327

#SPJ11

The work function, fermi energy, and vacuum energy are all related to the energy levels of electrons in a material. The work function is the minimum energy required to remove an electron from the surface of a material, while the fermi energy is the highest energy level occupied by electrons at absolute zero temperature. The vacuum energy is the lowest possible energy level that exists in a vacuum.

In materials, the fermi energy is determined by the number of available energy states for electrons to occupy. The work function is related to the difference in energy between the fermi level and the vacuum level. Specifically, the work function is equal to the difference between the fermi energy and the vacuum energy.

Therefore, the work function, fermi energy, and vacuum energy are all closely related to the electronic properties of a material and the energy levels available to its electrons.

Learn more about work function here:

https://brainly.com/question/19427469

#SPJ11

The answer is (c) 16 times.

The height reached by an object thrown straight up depends on its initial velocity and the acceleration due to gravity. The formula for the height reached is h = (v²)/(2g), where v is the initial velocity and g is the acceleration due to gravity (9.8 m/s²).

If the first rock is thrown with twice the initial velocity of the second rock, then its initial velocity is v1 = 2v². Using the formula, we can calculate the height reached by each rock:

h1 = (2v2)²/(2g) = (4v2²)/(2g) = 2v2²/g

h2 = v2²/(2g)

To find the difference in height reached by the two rocks, we can take the ratio of h1 to h2:

h1/h2 = (2v2²/g)/(v2²/(2g)) = 4

So the first rock will reach a height that is 4 times higher than the second rock. However, the question asks for the ratio of the heights at the apex, which is when the rocks stop and start falling back down. At this point, both rocks have a velocity of 0 m/s.

Using the formula h = (v²)/(2g), we can calculate the height at the apex for each rock:

h1 = (2v2)²/(2g) = (4v2²)/(2g) = 2v2²/g

h2 = v2²/(2g)

Since both rocks have the same acceleration due to gravity and are starting from the same height, the ratio of their heights at the apex is simply the ratio of their initial velocities squared:

h1/h2 = (2v2)²/v2² = 4² = 16

Therefore,a rock is thrown straight up with twice the initial velocity of another that the first rock will be 16 times higher than the second rock at its apex.

To know more about velocity visit:

brainly.com/question/17127206

#SPJ11

Sure, I'd be happy to help!

To create a string of random length, we can use a procedure called "Strings". This procedure should include an array that is used to temporarily store the string. Since we don't know what the length of the string will be, we should declare the array to be the maximum size that we expect the string to be.

Within the Strings procedure, we can use indexed addressing to move through the array and generate a random string. Depending on your programming language, there may be different ways to generate a random string. One common method is to use a loop to randomly select characters from a pre-defined set of possible characters and append them to the temp string until the desired length is reached.

After we have generated the random string, it is important to clear the temp string so that it is ready for future use. To do this, we can create another procedure called "ClrString". This procedure should simply set all elements of the array to be empty or null, depending on the data type used.

By using these procedures together, we can easily generate random strings of any length and then clear the temp string so that it is ready for the next use. I hope that helps! Let me know if you have any other questions.
Hi! To create a procedure that generates a string of random length and temporarily stores it in an array, follow these steps:

1. Declare an array with the maximum possible size to temporarily store the string. For example, `tempString[100]`.

2. Create a procedure called `Strings` that generates a random length for the string, and fills the array with characters accordingly using indexed addressing.

3. Within the `Strings` procedure, you may call other procedures if needed to generate the random characters for the string.

4. After using the temporary string, you will need to clear it. To do this, create another procedure called `C r String` that resets the elements of the `temp String` array to their initial values.

In summary, the `Strings` procedure will create a string of random length and store it in the `temp String` array. After using the temporary string, call the `ClrString` procedure to clear the contents of the array.

The strength of the resulting magnetic field at a distance of 61.1 cm from the wire is approximately 2.97 × 10⁻⁵ T.

To find the strength of the resulting magnetic field at a distance of 61.1 cm from the wire with a 27.5 A current flowing through it, we will use the following formula:

Magnetic field strength (B) = (μ₀ * I) / (2 * π * r)

where,
- B is the magnetic field strength
- μ₀ is the permeability of free space (4π × 10⁻⁷ T m/A)
- I is the current in the wire (27.5 A)
- r is the distance from the wire (61.1 cm, which is 0.611 m)


1. Convert the distance from cm to m: 61.1 cm = 0.611 m
2. Apply the formula: B = (4π × 10⁻⁷ T m/A * 27.5 A) / (2 * π * 0.611 m)

3. Simplify and solve for B:
  B = (4π × 10⁻⁷ T m/A * 27.5 A) / (2 * π * 0.611 m)
  B ≈ (1.21 × 10⁻⁶ T m * 27.5 A) / (1.222 m)
  B ≈ 2.97 × 10⁻⁵ T

At a distance of 61.1 cm from the wire, the resulting magnetic field has a strength of roughly 2.97 × 10⁻⁵ T.

Learn more about "magnetic field": https://brainly.com/question/7802337

#SPJ11

As the number of resistors in a series circuit increases, the overall resistance increases.

A series circuit is a current pathway that lets electrons flow to one or more resistors.

In series circuit, the current flowing in each circuit component is the same, while the voltage across the circuit components are differnt.

The equivalent resistance of a series curict is obtained by adding all the inididual resistance of the circuit.

Re = R1 + R2 + R3

where;

So in a series circuit, as the number of resistance increases, the overall resistance or equivalent resistance increases.

Learn more about series circuit here: https://brainly.com/question/19865219

#SPJ1

The final temperature when 5g of ice at 0°C is mixed with 5g of steam at 100°C can be found by calculating the heat transfer between the two substances.

Since both ice and steam have the same mass, their heat transfers will be equal in magnitude but opposite in direction.
First, we need to find the heat required to melt the ice and convert it into water. For this, we use the formula Q = mL, where Q is the heat transfer, m is the mass, and L is the latent heat of fusion for ice (334 J/g). Thus, Q = 5g × 334 J/g = 1670 J. Next, we calculate the heat required to condense the steam into water. We use the formula Q = mL, with L being the latent heat of vaporization for water (2260 J/g). Q = 5g × 2260 J/g = 11300 J. Since 1670 J is not enough to fully condense the steam, the final temperature will be 100°C, with some of the steam still remaining as steam. Therefore, the answer is A. 100°C.

Learn more about fusion here : https://brainly.com/question/30403515

#SPJ11

The final temperature when 5g of ice at 0°C is mixed with 5g of steam at 100°C can be found by calculating the heat transfer between the two substances.

Since both ice and steam have the same mass, their heat transfers will be equal in magnitude but opposite in direction.
First, we need to find the heat required to melt the ice and convert it into water. For this, we use the formula Q = mL, where Q is the heat transfer, m is the mass, and L is the latent heat of fusion for ice (334 J/g). Thus, Q = 5g × 334 J/g = 1670 J. Next, we calculate the heat required to condense the steam into water. We use the formula Q = mL, with L being the latent heat of vaporization for water (2260 J/g). Q = 5g × 2260 J/g = 11300 J. Since 1670 J is not enough to fully condense the steam, the final temperature will be 100°C, with some of the steam still remaining as steam. Therefore, the answer is A. 100°C.

Learn more about fusion here : https://brainly.com/question/30403515

#SPJ11

The speed of the sound wave in the guitar that has 1.5 m long wire having 250 N tension and mass of the wire is 50 g, is 86.6 m/s.

To find the speed of the sound wave in the guitar wire, we need to use the formula:

Speed = √(Tension / (Mass per unit length))

Where tension is given as 250 N,

Mass per unit length can be calculated as mass / length = 50 g / 1.5 m = 33.33 g/m = 0.03333 kg/m (converting grams to kilograms).

Plugging in the values, we get:

Speed = √(250 N / 0.03333 kg/m) = √7500 m/s = 86.6 m/s

Therefore, the speed of the sound wave in the guitar wire is 86.6 m/s.

Learn more about the speed of the sound wave:

https://brainly.com/question/2142871

#SPJ11

In the movie "American Beauty," capitalism and patriarchy are portrayed as forces that contribute to the main character's sense of dissatisfaction and ennui.

The protagonist, Lester, is a middle-aged man who is disenchanted with his job and his suburban life, which is built on the foundations of capitalism and patriarchal values. The images projected in today's media that are a result of gender inequality often perpetuate unrealistic beauty standards and promote gender roles that reinforce traditional gender norms. These images can send harmful messages to young people, such as the idea that physical appearance is more important than character or that women should prioritize their looks over their intellect or accomplishments.

To know more about patriarchy, here

brainly.com/question/29547211

#SPJ1

According to Bernoulli's equation, the pressure at the bottom of tube 1 is as follows: p1 + 1/2 ρ v1² = p0 + [tex]1/2[/tex]ρ v², we get p1 = p0 + ρ g (h2 - h1)/(1 - A1²/A2²)

p1 = p0 + [tex]\frac{x}{y} 1/2[/tex] ρ V²

The continuity equation, which asserts that the mass flow rate is constant throughout the pipe, can be used to determine v0. Thus:

v² = A² v²

where v2 is the fluid's speed at the right end of the pipe, which is also the fluid's speed where tube 2 is located. Upon solving for v2, we obtain:

v² = (A1/A²) v1

The following results are obtained using the Bernoulli equation between the pipe's left end and tube 2's location:

P² + [tex]1/2[/tex] v² + g h² = p0 + [tex]1/2[/tex]v0 + 2

where p2 is the pressure in tube 2's bottom. Rearranging and replacing v2 results in the following:

v0 = 2g²(h2 - h1)/(1 - A[tex]1/2[/tex]/A2²))

Substituting this into the equation for p1, we get:

p1 = p0 + 1/2 ρ 2²(h2 - h1)/(1 - A1²/A2²))]²

Simplifying, we get:

p1 = p0 + ρ g (h2 - h1)/(1 - A1²/A2²)

B) The continuity equation, which asserts that the mass flow rate is constant throughout the pipe, can be used again to determine v1. Thus:

A1 v1 = A² v²

P² + [tex]1/2[/tex] v2 + g h²= p0 + [tex]1/2[/tex] v0 + 2

where p2 is the pressure in tube 2's bottom.

Rearranging and replacing v2 results in the following:

v1 = (A²/A1) v²

v1 = (2g(h² - h1)/(1 - A1²/A²) sqrt(A²/A1))

or

where the cross-sectional area ratio is given by = A1A2.

to know more about Pressure here:

brainly.com/question/12971272

#SPJ1

The path followed by the particle can be traced by the equations  x(t) = -2 + 8t/√68 and y(t) = 1 - 2t/√68..

To find the path followed by a light-seeking particle originating at the center of the neighborhood near point (-2,1), we need to consider the intensity function I(x, y) = A - 2x^2 - y^2.

1: Determine the gradient of the intensity function.
Calculate the partial derivatives with respect to x and y:
∂I/∂x = -4x
∂I/∂y = -2y

2: Find the direction of the gradient at the given point (-2,1).
Evaluate the partial derivatives at the point (-2,1):
∂I/∂x(-2,1) = -4(-2) = 8
∂I/∂y(-2,1) = -2(1) = -2

3: Normalize the gradient vector.
The gradient vector is (8, -2). Find its magnitude:
|gradient| = √(8^2 + (-2)^2) = √(64 + 4) = √68

Normalize the gradient vector by dividing each component by the magnitude:
Normalized gradient = (8/√68, -2/√68)

4: Determine the path followed by the light-seeking particle.
The path of the light-seeking particle is along the direction of the normalized gradient, originating from the center of the neighborhood near point (-2,1). The path can be represented parametrically as:
x(t) = -2 + 8t/√68
y(t) = 1 - 2t/√68

In conclusion, the path followed by a light-seeking particle that originates at the center of the neighborhood near point (-2,1) can be described parametrically by the functions x(t) = -2 + 8t/√68 and y(t) = 1 - 2t/√68.

To learn more about "intensity of light", visit: https://brainly.com/question/28145811

#SPJ11

Here might have some misunderstanding in electromagnetic waves because both choices A and C require the transfer of charges. Option A is Correct.

The right response is Option A, "accelerating electric charges," as any change in the velocity of an electric charge disturbs the electromagnetic field and causes a wave to radiate outward. The electromagnetic radiation hypothesis refers to this.

This is just one particular application of the more basic principle of accelerating electric charges; option C, vibrating atoms and molecules, also generates electromagnetic waves. Electromagnetic waves are really produced by vibrating atoms and molecules.

Since option A covers both the situations of vibrating atoms and molecules and other sorts of accelerating electric charges, it is a more inclusive and accurate response.

Learn more about electromagnetic waves visit: brainly.com/question/13874687

#SPJ4

The magnitude and direction of the magnetic field are approximately 1.55 T and eastward, respectively.

To find the magnitude and direction of the magnetic field acting on an electron moving northward with a force acting upward, we can use the formula for the force experienced by a charged particle in a magnetic field:
F = q * v * B * sin(θ)
Where F is the force (7.2 x 10⁻¹³ N), q is the charge of the electron (-1.6 x 10⁻¹⁹ C), v is the velocity (2.9 x 10⁶ m/s), B is the magnitude of the magnetic field, and θ is the angle between the velocity and magnetic field directions.

Since the force is upward and the electron is moving northward, we can conclude that the angle theta between the velocity and magnetic field is 90 degrees, and sin(90) = 1.

Now, we can solve for B:
B = F / (q * v)

B = (7.2 x 10⁻¹³ N) / (-1.6 x 10⁻¹⁹ C * 2.9 x 10⁶ m/s)

B ≈ -1.55 (Tesla)

The magnitude of the magnetic field is approximately 1.55 T.

Since the force is upward, and the electron is moving northward, we can conclude that the magnetic field direction is to the east, using the right-hand rule.

Learn more about magnetic field:

https://brainly.com/question/7645789

#SPJ11

The magnitude and direction of the magnetic field are approximately 1.55 T and eastward, respectively.

To find the magnitude and direction of the magnetic field acting on an electron moving northward with a force acting upward, we can use the formula for the force experienced by a charged particle in a magnetic field:
F = q * v * B * sin(θ)
Where F is the force (7.2 x 10⁻¹³ N), q is the charge of the electron (-1.6 x 10⁻¹⁹ C), v is the velocity (2.9 x 10⁶ m/s), B is the magnitude of the magnetic field, and θ is the angle between the velocity and magnetic field directions.

Since the force is upward and the electron is moving northward, we can conclude that the angle theta between the velocity and magnetic field is 90 degrees, and sin(90) = 1.

Now, we can solve for B:
B = F / (q * v)

B = (7.2 x 10⁻¹³ N) / (-1.6 x 10⁻¹⁹ C * 2.9 x 10⁶ m/s)

B ≈ -1.55 (Tesla)

The magnitude of the magnetic field is approximately 1.55 T.

Since the force is upward, and the electron is moving northward, we can conclude that the magnetic field direction is to the east, using the right-hand rule.

Learn more about magnetic field:

https://brainly.com/question/7645789

#SPJ11

With a price ceiling of $4 per unit, the government has set a maximum price that can be charged for wheat.

Since the supply curve is Q=10p, at a price of $4, the quantity supplied will be 10 x 4 = 40 units. On the other hand, the demand curve is Q = 120 - 10p, so at a price of $4, the quantity demanded will be 120 - 10 x 4 = 80 units.

Therefore, with a price ceiling of $4, the quantity demanded exceeds the quantity supplied, resulting in a shortage of 80 - 40 = 40 units. This means that consumers will not be able to purchase as much wheat as they desire at the price ceiling.

The equilibrium price and quantity are where the supply and demand curves intersect, and in this case, the equilibrium price would be found by setting the two equations equal to each other:

120 - 10p = 10p

Solving for p, we get p = $6 per unit as the equilibrium price.

At this price, the quantity demanded and supplied are both equal to 60 units. Therefore, the price ceiling of $4 per unit results in a shortage of 40 units and a lower quantity supplied than the equilibrium quantity. The equilibrium price also increases from $6 to $4 per unit.

Learn more about demand curve: https://brainly.com/question/6075885

#SPJ11

a) The altitude of the satellite is approximately 1.15 x 10⁷ m.

b) The value of g at the location of this satellite is approximately 2.08 m/s².

a) The altitude of the satellite can be found using the formula for the period of a circular orbit: T = 2π√(r³/GM), where T is the period, r is the distance from the center of the Earth to the satellite, G is the gravitational constant, and M is the mass of the Earth. Solving for r, we get r = (GMT²/4π²)^(1/3). Substituting the given values, we get r ≈ 1.15 x 10² m.

b) The value of g at the location of the satellite can be found using the formula for gravitational acceleration: g = GM/r², where G is the gravitational constant, M is the mass of the Earth, and r is the distance from the center of the Earth to the satellite. Substituting the values found in part (a), we get g ≈ 2.08 m/s².

To learn more about gravitational force, here

https://brainly.com/question/12528243

#SPJ4

The total resistance of the circuit R is 4.36 ohms

The current drawn from the battery B is 1.146A

The terminal voltage of the battery is 4.99V

In physics, "current" usually refers to the flow of electric charge through a conductor, which is measured in units of amperes (A).

Electric current is a fundamental concept in electrical engineering and is central to the operation of many electrical devices, including motors, generators, and electronic circuits.

Electric current can be either direct current (DC) or alternating current (AC). In DC, the flow of electric charge is unidirectional, whereas in AC, the direction of the flow of electric charge periodically reverses

Read more about resistor here:

https://brainly.com/question/24858512

#SPJ1

The net capacitance of the circuit is 3.80 μF.

To find the net capacitance of this circuit, we need to use a combination of series and parallel capacitance formulas. Firstly, the two capacitors connected in series can be simplified to a single equivalent capacitor, given by:

1/Ceq = 1/C1 + 1/C2
1/Ceq = 1/3.00 μF + 1/4.00 μF
1/Ceq = 0.55556 μF^-1
Ceq = 1.80 μF

Now, the equivalent capacitor Ceq is connected in parallel with the 2.00 μF capacitor, so the total capacitance Ctotal of the circuit can be found using the parallel capacitance formula:

Ctotal = Ceq + C3
Ctotal = 1.80 μF + 2.00 μF
Ctotal = 3.80 μF

In summary, the given circuit consists of three capacitors connected in series and parallel. By simplifying the two capacitors connected in series to a single equivalent capacitor, we can apply the parallel capacitance formula to find the total capacitance of the circuit. The net capacitance is then found to be 3.80 μF.

Here you can learn more about net capacitance

https://brainly.com/question/30905469#

#SPJ11  

The mass of the nucleus with a radius of 2.8 x 10^-15 m is about 2.1 x 10^-27 kg or approximately 1.26 u.

To estimate the mass of a nucleus with a radius of 2.8 x 10^-15 m, we can use the following steps:
1. Determine the volume of the nucleus, assuming it's a sphere: V = (4/3)πr^3
2. Use the nuclear density to find the mass: ρ = mass/volume
3. Convert the mass to atomic mass units (u)
Nuclear density (ρ) is approximately constant at 2.3 x 10^17 kg/m^3.
Step 1: Calculate the volume of the nucleus:
V = (4/3)π(2.8 x 10^-15 m)^3 ≈ 9.15 x 10^-45 m^3
Step 2: Calculate the mass of the nucleus:
mass = ρ * V ≈ (2.3 x 10^17 kg/m^3)(9.15 x 10^-45 m^3) ≈ 2.1 x 10^-27 kg
Step 3: Convert the mass to atomic mass units (u):
mass (u) = mass (kg) / (1 u) ≈ (2.1 x 10^-27 kg) / (1.6605 x 10^-27 kg/u) ≈ 1.26 u
The mass of the nucleus with a radius of 2.8 x 10^-15 m is about 2.1 x 10^-27 kg or approximately 1.26 u.

Learn more about nuclear density here: https://brainly.com/question/13180243

#SPJ11

The energy in joules of an x-ray photon with a wavelength of 2.78 × 10^−10 m is approximately 7.144 × 10^−16 J.

To calculate the energy in joules of an x-ray photon with a wavelength of 2.78 × 10^−10 m, you can use the formula E = (hc) / λ, where E is energy, h is Planck's constant (6.626 × 10^−34 Js), c is the speed of light (2.998 × 10^8 m/s), and λ is the wavelength.

Plug in the given values.
E = (6.626 × 10^−34 Js) × (2.998 × 10^8 m/s) / (2.78 × 10^−10 m)

Multiply h and c.
E = (1.987 × 10^−25 Jm) / (2.78 × 10^−10 m)

Divide the result by λ.
E = 7.144 × 10^−16 J

Therefore, an x-ray photon with a wavelength of 2.78 1010 m has an energy of about 7.144 1016 J.

Learn more about "energy": https://brainly.com/question/13881533

#SPJ11

A. The capacitance of the circuit: [tex]2.22 x 10^{-3[/tex] F.

B.  The charge on the capacitor when it is fully charged is [tex]2.67 x 10^{-2[/tex]coulombs.

(a) To calculate the capacitance of the circuit, we can use the formula:
C = t / ([tex]R_{eq} * ln(V_0 / V_t)[/tex]))
Where t is the time elapsed,
[tex]R_{eq}[/tex] is the equivalent resistance,
[tex]V_0[/tex] is the initial voltage across the capacitor, and
[tex]V_t[/tex] is the voltage across the capacitor at time t.

Since the capacitor is fully charged, [tex]V_t[/tex] = [tex]V_0[/tex] and we can rewrite the formula as:
C = t / ([tex]R_{eq}[/tex] * ln(1))

Since ln(1) = 0, this simplifies to:
C = t / [tex]R_{eq}[/tex]

We don't have the value of t, so we can't calculate C directly. However, we can use another formula that relates capacitance, resistance, and time:
t = 5 *[tex]R_{eq}[/tex] * C

This formula tells us that it takes approximately 5 time constants for the capacitor to charge fully in an RC circuit. A time constant is equal to the product of the resistance and the capacitance, or RC.

Since we know R_eq is 450 Ω, we can rearrange the formula to solve for C:
C = t / (5 * [tex]R_{eq}[/tex])

We don't have the value of t, but we can assume that the capacitor has fully charged after 5 time constants, or 5RC. This means that:
t = 5 * RC

Substituting this into the previous equation gives us:
C = (5 * RC) / (5 * [tex]R_{eq}[/tex])
C = R /[tex]R_{eq}[/tex]

Thus, the capacitance of the circuit is equal to the resistance divided by the equivalent resistance:
C = R / [tex]R_{eq}[/tex]
C = 1000 / 450
C = 2.22 x[tex]10^{-3[/tex]F

(b) To find the charge on the capacitor when it is fully charged, we can use the formula:
Q = C * V
Where Q is the charge on the capacitor,
C is the capacitance, and
V is the voltage across the capacitor.

Since the capacitor is fully charged, V = [tex]V_0[/tex]. We don't have the value of [tex]V_0[/tex], but we can assume that it is equal to the voltage of the source, which is not given in the problem. Let's use a hypothetical value of 12 V.

Then, the charge on the capacitor is:
Q = C * V
Q = (2.22 x [tex]10^{-3[/tex] F) * (12 V)
Q = 2.67 x [tex]10^{-2[/tex] C

To know more about "RC circuit" refer here:

https://brainly.com/question/2741777#

#SPJ11

The driver of the car hears the sound of the siren at a frequency of approximately 932.34 Hz.

The frequency at which the driver of the car hears the siren can be calculated using the Doppler effect formula:
f' = f * (v + vo) / (v + vs)
Where:
- f' is the observed frequency (the frequency heard by the driver)
- f is the source frequency (800 Hz in this case)
- v is the speed of sound in the medium (343 m/s at 20°C)
- vo is the speed of the observer (the car) relative to the medium (1000 cm/s, which should be converted to m/s)
- vs is the speed of the source (the truck) relative to the medium (40 m/s)
First, convert the car's speed from cm/s to m/s:
1000 cm/s * (1 m/100 cm) = 10 m/s
Next, plug the values into the Doppler effect formula:
f' = 800 Hz * (343 m/s + 10 m/s) / (343 m/s - 40 m/s)
f' = 800 Hz * (353 m/s) / (303 m/s)
f' ≈ 932.34 Hz
So, the driver of the car hears the siren at a frequency of approximately 932.34 Hz.

Learn more about frequency: https://brainly.com/question/254161

#SPJ11

1.50 atm is equal to 1140 mm hg

What does one atm mean?

The standard unit of measurement known as one atmosphere (atm) corresponds to the average atmospheric pressure at sea level and 15 degrees Celsius. (59 degrees Fahrenheit). 1,013 millibars, or 760 millimeters (29.92 inches) of mercury, make up one atmosphere. As height rises, atmospheric pressure decreases.

The force that the air above the ground applies to it as it is drawn to the earth by gravity is known as atmospheric pressure. A barometer is typically used to measure atmospheric pressure. The unit atmosphere serves as a metaphor for it.

1 atm = 760 mm Hg

So 1.5 atm will be 1140mmHg

To learn more about atmospheric pressure use:

https://brainly.com/question/15215203

#SPJ1

Photons could have created muon antimuon pairs at a temperature of approximately 1.6 * 10^{12} K.

To determine the temperature at which photons could have created muon antimuon pairs, we need to use the equation:
E = 2mμc^2
where E is the energy of the photon, mμ is the mass of the muon, and c is the speed of light. We can rearrange this equation to solve for the energy of the photon:
E = \frac{2mμc^{2}}{ 2}
E = mμc^{2}
Now we can use the Boltzmann constant to relate the energy of the photon to temperature:
E = kB T
where T is the temperature and kB is the Boltzmann constant. Rearranging this equation to solve for temperature, we get:
T = \frac{E }{ kB}
Substituting in the expression we derived for the energy of the photon, we get:
T =\frac{ mμc^{2 }}{kB}
Plugging in the given value for the mass of the muon, we get:
T = \frac{(1.88 * 10^{-28} kg) (299,792,458 m/s)^{2 }}{ kB}
Using the value of the Boltzmann constant, kB = 1.38064852 * 10^{-23} m^{2 }kg s^{-2} K^{-1}, we get:
T =\frac{ (1.88 * 10^{-28} kg) (299,792,458 m/s)^{2 }{ (1.38064852 * 10^{-23} m^{2 }kg s^{-2} K^{-1})
T ≈ 1.6 * 10^{12} K

learn more about antimuon pairs Refer: https://brainly.com/question/30888729

#SPJ11

The correct expression for the induced electric field inside the solenoid as a function of the distance from its axis, for a region where r < R, is E = -μ₀nπr² di/dt

where μ₀ is the permeability of free space, n is the number of turns per meter, r is the distance from the solenoid's axis, and di/dt is the rate of change of current with respect to time. This expression is derived from Faraday's law of electromagnetic induction, which states that the induced electric field is proportional to the rate of change of magnetic flux through a loop.

In the case of a solenoid, the magnetic field inside the solenoid is proportional to the current and the number of turns per unit length (n), and the magnetic flux is proportional to the cross-sectional area of the solenoid (πr²). Therefore, the correct expression for the induced electric field takes into account these factors and is given by -μ₀nπr² di/dt.

You can learn more about electric fields at: brainly.com/question/15800304

#SPJ11

a) Its focal length is half the radius of curvature, or 10 cm.

b) The image of the candle will be located 17.5 cm from the mirror.

c) The image will be upright.

(a) The focal length of the mirror can be calculated using the formula:

1/f = 1/do + 1/di

where f is the focal length, do is the distance of the object from the mirror, and di is the distance of the image from the mirror.

In this case, do = 35 cm and the mirror has a radius of curvature of 20 cm, so its focal length is half the radius of curvature, or 10 cm.

(b) To find the location of the image, we can use the mirror formula:

1/do + 1/di = 1/f

Plugging in the values we have, we get:

1/35 + 1/di = 1/10

Solving for di, we get:

di = 17.5 cm

So the image of the candle will be located 17.5 cm from the mirror.

(c) To determine whether the image is upright or inverted, we can use the sign convention:

- If the object distance (do) is positive, the object is on the same side of the mirror as the incoming light, and the image is upright.
- If the object distance is negative, the object is on the opposite side of the mirror from the incoming light, and the image is inverted.

In this case, the object is 35 cm from the mirror, which is on the same side of the mirror as the incoming light. Therefore, the image will be upright.

To know more about focal length refer here:

https://brainly.com/question/16188698

#SPJ11

The maximum coefficient of performance (COP) for the freezer is 7.33.

To calculate the maximum coefficient of performance (COP) for a freezer set to maintain the cold space at -1.5°F and located in a kitchen maintained at 61°F, you'll need to use the following formula:
COP_max = T_cold / (T_hot - T_cold)

First, convert the temperatures from Fahrenheit to Kelvin:
T_cold = (-1.5°F + 459.67) × 5/9 = 254.54 K
T_hot = (61°F + 459.67) × 5/9 = 289.26 K

Next, plug the temperatures into the formula:
COP_max = 254.54 K / (289.26 K - 254.54 K)
COP_max ≈ 254.54 K / 34.72 K
COP_max ≈ 7.33

This is the maximum coefficient of performance (COP) for the freezer.

Learn more about coefficient:

https://brainly.com/question/4219149

#SPJ11

a. Therefore, the work done by the force is W = [tex]a^2b.[/tex]

b. Therefore, the work done by the force in this case would be W = 1.5[tex]b^2.[/tex]

(a) To find the work done by the force, we need to integrate the dot product of the force and the displacement vector along the path of motion. Along the x-axis, the displacement vector is →dx = [tex]dx_i[/tex], where dx = a. The force →F only has an x-component, so the dot product is:

→F · →dx = [tex](2xy_i+3y_j) * (dx_i)[/tex]

= 2xydx

Integrating this expression from x=0 to x=a, we get:

W = ∫→F · →dx = ∫0a 2xy dx = [tex][x^2y[/tex] ] oa = [tex]a^2b.[/tex]

Therefore, the work done by the force is W = [tex]a^2b.[/tex]

(b) If the particle had moved from the origin to the point with coordinates (a, b) by moving first along the y-axis to (0, b), then parallel to the x-axis, the dot product of the force and the displacement vector would be:

→F · →dy =[tex](2xy_i+3y_j) * (dy_j)[/tex]

= 3ydy

Along the y-axis, the displacement vector is dy = b. Integrating this expression from y=0 to y=b, we get:

W = ∫→F · →dy = ∫0b 3y dy = [[tex]1.5y^2[/tex]]0b

= 1.5[tex]b^2[/tex]

Therefore, the work done by the force in this case would be W = .5[tex]b^2[/tex]

Learn more about force Visit: brainly.com/question/25239010

#SPJ4

Answer: The work done pushing the car up the hill is approximately 116007 joules (J)

Explanation: To calculate the work done in pushing a car up a hill, we can use the formula:

Work = Force x Distance x cos(theta)

where:

Force = 9000 N (the force applied)

Distance = 15 m (the distance the car is pushed)

theta = 35 degrees (the angle of the incline)

First, we need to convert the angle to radians:

theta = 35 degrees = 35 * (pi/180) radians ≈ 0.6109 radians

Now we can plug in the values and solve for work:

Work = 9000 N x 15 m x cos(0.6109) ≈ 116007 J

Answer: The work done pushing the car up the hill is approximately 116007 joules (J)

Explanation: To calculate the work done in pushing a car up a hill, we can use the formula:

Work = Force x Distance x cos(theta)

where:

Force = 9000 N (the force applied)

Distance = 15 m (the distance the car is pushed)

theta = 35 degrees (the angle of the incline)

First, we need to convert the angle to radians:

theta = 35 degrees = 35 * (pi/180) radians ≈ 0.6109 radians

Now we can plug in the values and solve for work:

Work = 9000 N x 15 m x cos(0.6109) ≈ 116007 J