Answer: New wheels should be re-torqued after the first 50 to 100 driving miles. This should be done in case the clamping loads have changed following the initial installation due to the metal compression/elongation or thermal stresses affecting the wheels as they are breaking in, as well as to verify the accuracy of the original installation.
Answer:
I thinkC
Explanation:
Technician A says that the connecting rod and main bearing caps should be marked before removing to ensure that they can be installed in the exact same location when reassembled. Technician B says that the tip of the valve stem should be filed before removing valves from the cylinder head to help prevent damage to the valve guide. Who is right
Answer:
Technician A
Explanation:
This is because when the dimacations are made, the surface area and length respectively can be maintained to reduce to idea of force which may lead to damage
in the multiple pipe system shown below, which of the following is true concerning the linear system?.
Answer:
maybe
Explanation:
th liner pupe us it it had ore moecuke and tepiract
what is the largest, low-cost airline carrier in the world, which recently canceled thousands of flights for reasons partially disputed by the federal aviation administration?
The largest, low-cost airline carrier in the world that recently canceled thousands of flights for reasons partially disputed by the federal aviation administration (FAA) is Southwest Airlines.
Southwest Airlines canceled 2,500 flights in just a few days.
According to Southwest Airlines, the cause of the cancellation is due to air traffic control problems and disruptive weather.
While FAA claimed that nothing like a reported case of air traffic and staffing shortages.
Southwest Airlines is the world's largest low-cost carrier and has its main office is located in Dallas, Texas.
Hence, in this case, it is concluded that the correct answer is "Southwest Airlines."
Learn more here: https://brainly.com/question/24782945
Which of these systems creates and delivers high voltage sparks at the right time to ignite the air-fuel
mixture in the combustion chamber?
Answer: Ignition System
Explanation:
Ignition System is the systems creates and delivers high voltage sparks at the right time to ignite the air-fuel mixture in the combustion chamber.
What are the 3 types of ignition systems?Automotive ignition systems can be categorised: coil-on-plug, distributor-based, and distributor-free (COP). Early ignition systems delivered the spark at the appropriate time using entirely mechanical distributors.
Thus, it is Ignition System
For more details about types of ignition systems, click here:
https://brainly.com/question/14094081
#SPJ2
Which of these statements is true about Newton's First Law of Motion?
If the net force on an object is zero, its velocity will remain constant
An unbalanced force on an object will always impact the objects speed
an unbalanced force on an object will always change the objects direction
Answer:
the second one is correct
Explanation:
Explanation:
» If the net force on an object is zero, its velocity will remain constant
on gasoline powered boats, when should the blower be operated?
On gasoline powered boats, the blower should be operated before starting the engine, during fueling, etc.
In the following circumstances, the blower should be used on boats powered by petrol:
It's crucial to run the blower for a few minutes before starting the engine.It is advised to keep the blower going while you are fueling.When the vessel is in motion: Some marine safety recommendations advise running the blower continuously while the boat is underway, especially in enclosed engine compartments, however this is not required.Thus, during these conditions, one should operate the blower.
For more details regarding gasoline powered boats, visit:
https://brainly.com/question/4143582
#SPJ6
What are the rules for maintaining a time margin for safe driving?
Answer:
We should keep a good distance between the vehicle infront of us and from ours to avoid any type of accident.
3-second rule=>allowing a minimum of 3 seconds of travel between our vehicle and the vehicle we are behind.
Explanation:
HOPE IT HELPS YOU!!Write a short summary of the power of dreams
Answer:
Walker went on to front Paranoid Saints, the Ex-Kings and the Bollox.
Reunion
In November 2009, Power of Dreams announced a reformation and tour to promote the 20th anniversary re-release of their first album (on 100% Music)[8] in March 2010.[9] In December 2010, a further tour of Ireland took place with Sultans of Ping and The Frank and Walters to support the release of a compilation album, 1989: The Best of Power of Dreams, which included a new track.[10] Power of Dreams' most recent gig was as part of "Indie Daze" at London's Forum in September 2014.
In March 2011, Keith Walker announced an amicable departure from the band and has gone on to play with Sister Cities,[11] Being Cool Is Lonely and The Holy Coast.[12] Olney plays with a new band, Cat Meat.[13] Walker continued to perform as Power of Dreams and to work on new material alongside his new project, Mineral, based in Paris.[14] In 2014, The Avener had a chart-topping hit single in several European countries with "Fade Out Lines", a remix of a song written by Walker and Phoebe Killdeer (ex-Nouvelle Vague) for Phoebe Killdeer and the Short Straws' second album Innerquake, released in 2012.
In December 2011, Immigrants, Emigrants and Me appeared in the book 101 Irish Records You Must Hear Before You Die.[15] In April 2013, the album was in the Irish Independent's top 30 albums of all time.[16]
In 2020, Power of Dreams released two new singles, "America"/"Across the Shannon",[17][18] and "Hurricane",[19] to promote forthcoming album Aüslander.
In July 2021, Aüslander, their first album in 27 years was released by The state51 Conspiracy and became a new entry on the Official Irish Albums Chart Top 50 when it charted at Number 22 on the chart of 05 August 2021
2. How were scientists able to access a car's computer system?
3. What other looming dangers are there for drivers of newer, computer controlled
draw perpendicular lines based on the info in the image.
Which type of material is known as elastomers to materials scientists and engineers
Answer:
Rubber-like solids with elastic properties are called elastomers.
Explanation:
Answer:
Rubber-like solids with elastic properties are called elastomers.
Explanation: