Prove that the total energy of a binary system where both objects (m1,m2) are moving can be expressed as:
E= 1/2 µv^2 - GMµ/ r where the reduced µ = m1m2/ m1+ m2
is orbiting around a mass M = m1 + m2 fixed at the origin. Do not assume circular orbits; your solution should apply to the general case of elliptical orbits.

The weight of a 100 oz box is either 200 lbs or 27.78231 kg depending on the units used for acceleration due to gravity.

To find the weight of a 100 oz box, we'll first need to convert ounces to either pounds (for fps units) or kilograms (for mks units), and then multiply by the acceleration due to gravity (g).

Convert ounces to pounds or kilograms
1 ounce (oz) = 0.0625 pound (lb)
1 ounce (oz) = 0.0283495 kilogram (kg)

100 oz = 100 * 0.0625 lb = 6.25 lb (for fps units)
100 oz = 100 * 0.0283495 kg = 2.83495 kg (for mks units)

Calculate weight using acceleration due to gravity
Weight in fps units:
g_fps = 32 ft/s²

Weight_fps = mass (lb) * g_fps
Weight_fps = 6.25 lb * 32 ft/s² = 200 lb*ft/s²

Weight in mks units:
g_mks = 9.8 m/s²

Weight_mks = mass (kg) * g_mks
Weight_mks = 2.83495 kg * 9.8 m/s² ≈ 27.78231 kg*m/s² (Newtons)

So, the weight of a 100 oz box is approximately 200 lb*ft/s² in fps units and 27.78231 kg*m/s² (Newtons) in mks units.

More on weight: https://brainly.com/question/30713045

#SPJ11

The factors determining the induced emf in a closed loop of wire are: 1. Magnetic field strength (B), 2. Area of the loop (A), 3. Rate of change of magnetic flux (dΦ/dt), and 4. the relative orientation between the magnetic field and the loop.

The factors determining the induced emf in a closed loop of wire can be further explained as follows:

1. Magnetic field strength (B): The stronger the magnetic field, the higher the induced emf.
2. Area of the loop (A): A larger loop area leads to a greater induced emf.
3. Rate of change of magnetic flux (dΦ/dt): The faster the magnetic flux changes through the loop, the higher the induced emf.
4. Relative orientation between the magnetic field and the loop: When the magnetic field lines are perpendicular to the loop, the induced emf is maximized.
To calculate the induced emf, we can use Faraday's law of electromagnetic induction, which states:
Induced emf = - dΦ/dt
where Φ represents the magnetic flux through the loop (Φ = B * A * cosθ), and θ is the angle between the magnetic field lines and the normal to the loop. The negative sign indicates that the induced emf opposes the change in magnetic flux, as described by Lenz's law.

Learn more about emf: https://brainly.com/question/17329842

#SPJ11

The gravitational potential energy of the bike racer after climbing a 1500 m long road at 4.3 degrees is 83,851.7 Joules.

To calculate the change in gravitational potential energy during the climb, we can use the formula:

Gravitational Potential Energy (GPE) = m * g * h

Where:
m = mass (76 kg)
g = gravitational acceleration (approximately 9.81 m/s²)
h = vertical height gained

First, we need to find the vertical height gained (h). We can use trigonometry to do this. Since we have the length of the road (1500 m) and the slope (4.3°), we can find the height using the sine function:

sin(slope) = height / length

height = sin(4.3°) * 1500 m

Now, let's calculate the height:

height = 0.0749 * 1500
height = 112.46 m

Now that we have the height, we can calculate the change in gravitational potential energy:

GPE = 76 kg * 9.81 m/s² * 112.46 m
GPE = 83851.7 J (Joules)

The gravitational potential energy changes by 83,851.7 Joules during the climb.

Learn more about gravitational potential energy:

https://brainly.com/question/15896499

#SPJ11

The gravitational potential energy of the bike racer after climbing a 1500 m long road at 4.3 degrees is 83,851.7 Joules.

To calculate the change in gravitational potential energy during the climb, we can use the formula:

Gravitational Potential Energy (GPE) = m * g * h

Where:
m = mass (76 kg)
g = gravitational acceleration (approximately 9.81 m/s²)
h = vertical height gained

First, we need to find the vertical height gained (h). We can use trigonometry to do this. Since we have the length of the road (1500 m) and the slope (4.3°), we can find the height using the sine function:

sin(slope) = height / length

height = sin(4.3°) * 1500 m

Now, let's calculate the height:

height = 0.0749 * 1500
height = 112.46 m

Now that we have the height, we can calculate the change in gravitational potential energy:

GPE = 76 kg * 9.81 m/s² * 112.46 m
GPE = 83851.7 J (Joules)

The gravitational potential energy changes by 83,851.7 Joules during the climb.

Learn more about gravitational potential energy:

https://brainly.com/question/15896499

#SPJ11

The temperature change of the bullet is 122.92 °C.

Kinetic energy is the energy possessed by a moving object by virtue of its motion.

The kinetic energy (KE) of the bullet is given by:

KE = 1/2 * m * v^2

where m is the mass of the bullet and v is its velocity.

Substituting the given values, we get:

KE = 1/2 * 0.0054 kg * (294 m/s)^2

KE = 112.19 J

All this kinetic energy is converted to thermal energy, which can be expressed as:

Q = m * c * ΔT

where Q is the thermal energy, m is the mass of the bullet, c is the specific heat capacity of lead, and ΔT is the change in temperature.

Substituting the given values and solving for ΔT, we get:

ΔT = Q / (m * c)

ΔT = 112.19 J / (0.0054 kg * 128 J/kg.°C)

ΔT = 122.92 °C

Therefore, the temperature change of the bullet is 122.92 °C.

Learn more about energy here:

https://brainly.com/question/1932868

#SPJ1

The change in momentum of puck is, -0.06 kg m/s.

Momentum is a vector quantity, meaning it has both magnitude and direction. It is conserved in a closed system, meaning that the total momentum of the system remains constant unless acted upon by an external force.

From the graph provided, the change in the puck's momentum from t=0ms to t=100ms can be calculated by finding the difference between the momentum at those two times.

The momentum at t=0ms is approximately 0.035 kg m/s, and the momentum at t=100ms is approximately -0.025 kg m/s. Therefore, the change in the puck's momentum is:

Change in momentum = (-0.025 kg m/s) - (0.035 kg m/s) = -0.06 kg m/s

To know more about momentum, here

brainly.com/question/30487676

#SPJ4

--The complete question is, Two ice hockey pucks with the same mass collide on a level, frozen pond. The first puck is initially at rest, and the second puck approaches it with a velocity of 10 m/s. The collision is approximately elastic, and there is almost no friction between the pucks and the surface. What is the change in the puck's momentum from t=0 ms to t=100 ms after the collision?--

To put numbers in scientific notation we use power of 10.

Scientific notation is a way or pattern of presenting very large numbers or very small numbers in a simpler form.

Scientific notation is a way of expressing numbers that are too large or too small to be conveniently written in decimal form, since to do so would require writing out an unusually long string of digits.

Usually, we use standard form while presenting numbers in scientific notation.

This standard form is usually in power of 10, for we can 0.0001 m in scientific notation as;

0.0001 m = 1 x 10⁻⁴ m

Learn more about scientific notation here: https://brainly.com/question/1767229

#SPJ1

The work required to accelerate the baton to an angular speed of 8.0 rad/s is 0.47 J.

The moment of inertia of the baton about its center is (1/12)mL^2 = 0.004 M^2 kg, where m is the mass and L is the length of the baton. The kinetic energy of the baton is (1/2)Iomega^2, where omega is the angular speed. Thus, the work done is the difference in kinetic energy between the final and initial states, which is (1/2)Iomega^2 - 0. The work required to accelerate the baton to an angular speed of 8.0 rad/s is 0.47 J.  The work done is 0.47 J, which is the energy required to give the baton an angular speed of 8.0 rad/s about its center.

learn more about accelerate here:

https://brainly.com/question/12550364

#SPJ11

The mass of the mallard duck whose speed is 8.2 and has a momentum of 10 kg.m/s is 1.22 kg.

To find the mass of the mallard duck, we will use the formula for momentum:

Momentum = Mass × Velocity

In this case, we are given the momentum (10 kg⋅m/s) and the velocity (8.2 m/s) and need to find the mass. We can rearrange the formula to solve for mass:

Mass = Momentum ÷ Velocity

Now, we can plug in the given values:

Mass = (10 kg⋅m/s) ÷ (8.2 m/s)

Mass = 1.22 kg

So, the mass of the mallard duck is approximately 1.22 kg.

Learn more about momentum:

https://brainly.com/question/18798405

#SPJ11

The maximum permissible current in the resistor is 0.632 A. The maximum voltage that can be applied across the resistor is 6.32 V.

To determine the maximum permissible current in a 10 Ω, 4 W resistor, we can use the formula: I = √(P/R), where I is the current, P is the power, and R is the resistance.

Substituting the values given, we get: I = √(4/10) = 0.632 A. Therefore, the maximum permissible current in the resistor is 0.632 A.

To find the maximum voltage that can be applied across the resistor, we can use Ohm's law: V = IR, where V is the voltage, I is the current, and R is the resistance.

Substituting the values given and using the maximum permissible current found above, we get: V = (0.632 A) x (10 Ω) = 6.32 V. Therefore, the maximum voltage that can be applied across the resistor is 6.32 V.

To know more about voltage, refer here:

https://brainly.com/question/13521443#

#SPJ11

The power of the camera lens is approximately 19.61 diopters.

The power of a lens is its ability to converge or diverge light rays passing through it. It is measured in diopters. The power of the lens is determined by its focal length, which is the distance between the lens and the image plane when the lens is focused on an object at infinity.

The power in diopters of a camera lens with a 51.0 mm focal length can be calculated using the formula:

D = 1 /f

Here,

D is the power of the camera lens in diopters

f is the focal length of the camera lens in meters

First, convert the focal length to meters:

51.0 mm = 0.051 m

Now, calculate the power in diopters:

Power (D) = 1 / 0.051 m ≈ 19.61 diopters

To know more about power of a camera lens, click here;

https://brainly.com/question/31056966

#SPJ11

After comparing the current (I) and resistance (R) of the crockpot and kettle, 2) Icrockpot < Ikettle and Rcrockpot > Rkettle.

We can use the formula: Power (P) = Voltage (V) × Current (I)

For the crockpot,
500 W = 240 V × Icrockpot
Icrockpot = 500 W / 240 V = 2.08 A

For the kettle,
1000 W = 240 V × Ikettle
Ikettle = 1000 W / 240 V = 4.17 A

Since 2.08 A < 4.17 A, we know Icrockpot < Ikettle.

Next, let's use Ohm's Law to find resistance: Voltage (V) = Current (I) × Resistance (R)

For the crockpot,
240 V = 2.08 A × Rcrockpot
Rcrockpot = 240 V / 2.08 A ≈ 115.38 Ω

For the kettle,
240 V = 4.17 A × Rkettle
Rkettle = 240 V / 4.17 A ≈ 57.55 Ω

Since 115.38 Ω > 57.55 Ω, we know Rcrockpot > Rkettle.

So, the correct answer is, 2) Icrockpot < Ikettle and Rcrockpot > Rkettle.

Learn more about "current": https://brainly.com/question/24858512

#SPJ11

After comparing the current (I) and resistance (R) of the crockpot and kettle, 2) Icrockpot < Ikettle and Rcrockpot > Rkettle.

We can use the formula: Power (P) = Voltage (V) × Current (I)

For the crockpot,
500 W = 240 V × Icrockpot
Icrockpot = 500 W / 240 V = 2.08 A

For the kettle,
1000 W = 240 V × Ikettle
Ikettle = 1000 W / 240 V = 4.17 A

Since 2.08 A < 4.17 A, we know Icrockpot < Ikettle.

Next, let's use Ohm's Law to find resistance: Voltage (V) = Current (I) × Resistance (R)

For the crockpot,
240 V = 2.08 A × Rcrockpot
Rcrockpot = 240 V / 2.08 A ≈ 115.38 Ω

For the kettle,
240 V = 4.17 A × Rkettle
Rkettle = 240 V / 4.17 A ≈ 57.55 Ω

Since 115.38 Ω > 57.55 Ω, we know Rcrockpot > Rkettle.

So, the correct answer is, 2) Icrockpot < Ikettle and Rcrockpot > Rkettle.

Learn more about "current": https://brainly.com/question/24858512

#SPJ11

The general solution for the spring-mass model x'' + 4x' + x = cos(2t) is x(t) = C1e^(-2t)cos(t) + C2e^(-2t)sin(t) + (1/5)cos(2t).

The transient part is C1e^(-2t)cos(t) + C2e^(-2t)sin(t), and the steady periodic part is (1/5)cos(2t). The amplitude of the steady periodic part is 1/5.

To find the general solution, we first solve the homogeneous equation x'' + 4x' + x = 0, which has the complementary function x_c(t) = C1e^(-2t)cos(t) + C2e^(-2t)sin(t).

Next, we find a particular solution for the given inhomogeneous equation by trying x_p(t) = A*cos(2t). Plugging x_p(t) into the equation and solving for A, we get A = 1/5. Thus, x_p(t) = (1/5)cos(2t). Finally, the general solution is the sum of the complementary function and the particular solution: x(t) = x_c(t) + x_p(t).

To know more about homogeneous equation click on below link:

https://brainly.com/question/30767168#

#SPJ11

The gravitational potential energy of the 9.3-kg mass on the surface of the Earth is zero joules.

What is Gravitational Potential Energy?

Gravitational potential energy is the energy possessed by an object due to its position in a gravitational field. It is defined as the amount of work done in lifting an object of mass "m" against the force of gravity "F" from a reference point to a certain height "h" above that point.

The gravitational potential energy (U) of an object with mass (m) at a height (h) above the surface of the Earth can be calculated using the formula:

U = mgh

where g is the acceleration due to gravity near the surface of the Earth, which is approximately 9.81 m/s^2.

Given that the mass of the object is 9.3 kg and it is on the surface of the Earth (h = 0), we can calculate the gravitational potential energy as:

U = (9.3 kg) x (9.81 m/s^2) x (0 m) = 0 J

Learn more about Gravitational Potential Energy from the given link

https://brainly.com/question/15896499

#SPJ1

The plane in which the particle is moving is the xy plane, which is a two-dimensional plane that is perpendicular to the z-axis.

Tell the position of a particle moving in the xy plane?

The position of a particle moving in the xy plane is given by the equation

x = t³ - 6t² + 9t + 1.

This equation describes the position of the particle as it moves along the x-axis with respect to time t. The particle's motion in the xy plane can be described by a curve in three-dimensional space, where the x-coordinate of the curve is given by the equation

x = t³ - 6t² + 9t + 1,

and the y and z coordinates are determined by the motion of the particle in the y and z directions. The plane in which the particle is moving is the xy plane, which is a two-dimensional plane that is perpendicular to the z-axis.

Learn more about position of a particle.

brainly.com/question/25066591

#SPJ11

In a wall clock if the length of the second hand is 16 cm then:

(A) The rotational speed of the second hand is 0.105 radians/second.

(B) The translation speed of the tip is 0.0168 meters/second.

(C) The rotational acceleration of the second hand is 0 radians/second².

A) To find the rotational speed of the second hand, we need to know how much it rotates in one second. Since the second hand completes a full rotation in 60 seconds, its rotational speed (ω) can be calculated using the formula:

ω = (total rotation) / (time taken)

A full rotation is 2π radians, so the rotational speed is:

ω = (2π radians) / (60 seconds)
ω = π/30 radians/second = 0.105 radians/second (to two significant figures)

B) To find the translational speed (v) of the tip of the second hand, we can use the formula:

v = ω * r

where ω is the rotational speed, and r is the length of the second hand. In this case, r = 16 cm = 0.16 meters. So, the translational speed is:

v = (0.105 radians/second) * (0.16 meters)
v = 0.0168 meters/second

C) Since the second-hand moves smoothly, its rotational acceleration (α) is 0. This means that there is no change in the rotational speed over time. In other words, the second hand rotates at a constant rate:

α = 0 radians/second²

Learn more about rotational acceleration:

https://brainly.com/question/29342095

#SPJ11

Demonstrate the normalisation of the radial wave function R21 for n = 2 and l = 1. (If necessary, substitute r and a.) R =, so we integrate throughout the entire r space to normalise. The wave function R21 was normalised as a result of the equation r2R*R dr = dr 242, 1" CO 1 = 5 24a.

A wave function is normalised by simply multiplying it by a constant to make sure that the probability of finding that particle is added up to one.

The normalisation constant and the equation also refer to the amplitude of the wave function that describes the particle in an infinite potential well For this constant, it is simple to solve for the amplitude after normalising the wave function.

To know more about wave function visit:-

https://brainly.com/question/17484291

#SPJ1

After passing through a 35000.0 volt potential difference, the proton gains a kinetic energy of 5.607 x 10⁻¹⁵ J and a final velocity of 3.07 x 10⁶ m/s.

Through a 100 kV potential difference, an electron and a proton that are at rest are accelerated.

The change in electric potential energy that the proton experiences as it goes from its beginning location to its final position is given by the potential difference V of 35000.0 volts:  ΔU = qV

The charge of a proton is q = +1.602 x 10⁻¹⁹ C.

ΔU = (1.602 x 10⁻¹⁹ C) * (35000.0 V) = 5.607 x 10⁻¹⁵ J

A particle with mass m and velocity v has the following kinetic energy:

K = (1/2) * m * v²

The proton has no initial kinetic energy since it is initially at rest. The proton's final kinetic energy, K', is as follows:

K' = ΔU = 5.607 x 10⁻¹⁵ J

Substituting the mass of a proton m = 1.673 x 10⁻²⁷ kg, we can solve for the final velocity v:

K' = (1/2) * m * v²

v = sqrt(2K'/m) = sqrt[(2*5.607 x 10⁻¹⁵ J) / (1.673 x 10⁻²⁷ kg)] = 3.07 x 10⁶ m/s

To know more about kinetic energy visit:-

https://brainly.com/question/21245662

#SPJ1

When applying Newton's 2nd law to an object on an inclined plane, we choose the coordinate axes parallel and perpendicular to the plane because it makes the gravitational force split into two components, one parallel and one perpendicular to the plane.

This allows us to consider the perpendicular component of the gravitational force separately from the applied force, and to calculate the net force along the parallel axis.

Choosing this coordinate system does not make the friction force negligible, nor does it make all the forces sum to zero. Additionally, it does not necessarily make acceleration along one axis equal to zero. However, applying Newton's 2nd law to an object on an inclined plane, we choose the coordinate axes parallel and perpendicular to the plane because it makes the gravitational force split into two components. Therefore, the correct option is none of the above.

Learn more about Newton: https://brainly.com/question/28171613

#SPJ11

The amount of work the charge escalator do to move 2.10 μc of charge from the negative terminal to the positive terminal of a 3.50 v battery is approximately 7.35 × 10⁻⁶ J.

To calculate the work done by the charge escalator in moving 2.10 μC of charge across a 3.50 V battery, you can use the formula:

Work = Charge × Voltage

In this case, the charge (Q) is 2.10 μC (microcoulombs) and the voltage (V) is 3.50 V. First, convert the charge to coulombs:

2.10 μC = 2.10 × 10⁻⁶ C

Now, plug the values into the formula:

Work = (2.10 × 10⁻⁶ C) × (3.50 V)

Work ≈ 7.35 × 10⁻⁶ J (joules)

The charge escalator does approximately 7.35 × 10⁻⁶ J of work to move the 2.10 μC charge from the negative to the positive terminal of the 3.50 V battery.

Learn more about work done here: https://brainly.com/question/8119756

#SPJ11

The mass of block b is 2.94 kg, calculated using conservation of energy.

We can use conservation of energy to solve this problem. The potential energy lost by block b as it falls through height h is equal to the kinetic energy gained by it at the bottom. We can write this as:

[tex]m_b_g_h[/tex] = (1/2)[tex]m_b_v[/tex]²

where [tex]m_b[/tex] is the mass of block b, g is the acceleration due to gravity, h is the height it falls through, and v is its speed at the bottom.

Solving for [tex]m_b[/tex], we get:

[tex]m_b[/tex] = 2gh/[tex]v^2[/tex]

Substituting the given values, we get:

[tex]m_b[/tex] = 29.812/ = 2.94 kg

Therefore, the mass of block b is approximately 2.94 kg.

Learn more about Conservation of energy

brainly.com/question/2137260

#SPJ11

(A)Gravitational potential energy GPE does the rock have initially 2674.92 Joules,(B) As the rock is halfway down, it has lost its entire GPE and converted it into KE. So, the KE will be equal to the GPE at this point i.e.1337.96J (C).The rock will be traveling at a speed of approximately 20.15 m/s when it is halfway down.

(A) The gravitational potential energy (GPE) of the rock initially can be calculated using the formula:

GPE = mgh

where:

m = mass of the rock = 6.6 kg

g = acceleration due to gravity = 9.8 m/s²

h = height of the cliff = 44.5 m

Plugging in the values:

GPE = 6.6 kg × 9.8 m/s² × 44.5 m = 2,674.92 J (Joules)

So, the rock initially has 2,674.92 Joules of gravitational potential energy.

(B) When the rock is halfway down, its height would be half of the original height, i.e., h/2 = 44.5 m / 2 = 22.25 m.

The gravitational potential energy (GPE) of the rock when it is halfway down can be calculated using the formula mentioned above:

GPE = mgh

where:

m = mass of the rock = 6.6 kg

g = acceleration due to gravity = 9.8 m/s²

h = height when halfway down = 22.25 m

Plugging in the values:

GPE = 6.6 kg × 9.8 m/s² × 22.25 m = 1,337.96 J (Joules)

The kinetic energy (KE) of the rock when it is halfway down can be calculated using the formula:

KE = (1/2)mv²

where:

m = mass of the rock = 6.6 kg

v = velocity of the rock

As the rock is halfway down, it is lost, its entire GPE and converted it into KE. So, the KE is equal to the GPE at this point.

KE = 1,337.96 J (Joules)

(C) To calculate the velocity (v) of the rock when it is halfway down, we can equate the KE to the formula for kinetic energy:

KE = (1/2)mv²

Plugging in the values:

1,337.96 J = (1/2) ×6.6 kg × v²

v² = (2 × 1,337.96 J) / 6.6 kg

v² = 406.32 m/s

v = √(406.32 m/s) = 20.15 m/s

So, the rock is traveling at a speed of approximately 20.15 m/s when it is halfway down.

To know more about GPE

https://brainly.com/question/17193232

#SPJ1

The velocity of the center of mass is (0.80 î + 3.38 ĵ) m/s.

The velocity of the center of mass of a system of particles can be calculated using the formula:

vcm = (m1v1 + m2v2 + ... + mn*vn) / (m1 + m2 + ... + mn)

where m1, m2, ..., mn are the masses of the particles and v1, v2, ..., vn are their velocities.

In this case, we have two particles with masses of 2.02 kg and 2.98 kg, and velocities of (1.99 î − 2.96 ĵ) m/s and (1.10 î + 5.98 ĵ) m/s, respectively. We can calculate the velocity of the center of mass as follows:

vcm = (m1v1 + m2v2) / (m1 + m2)

where m1 = 2.02 kg, m2 = 2.98 kg, v1 = (1.99 î − 2.96 ĵ) m/s, and v2 = (1.10 î + 5.98 ĵ) m/s.

Substituting the values, we get:

vcm = [(2.02 kg)(1.99 î − 2.96 ĵ) m/s + (2.98 kg)(1.10 î + 5.98 ĵ) m/s] / (2.02 kg + 2.98 kg)

Simplifying the expression, we get:

vcm = [(4.00 î + 16.92 ĵ) kg*m/s] / (5.00 kg)

vcm = (0.80 î + 3.38 ĵ) m/s

learn more about centre of mass here:

https://brainly.com/question/28996108

#SPJ11

(A) The individual receives an impulse from the ground because an impulse is equal to a change in momentum, and when a person jumps up from the ground, their momentum changes.

(b) The individual is affected by the floor, yes. When a force works over a distance, work is produced; in this instance, the floor pushes the person upward over a distance equal to the height of the leap.

(C) The equation p = mv, where m is the person's mass and v is their forward velocity, determines the momentum of the subject prior to jumping. The person's initial momentum was zero since they were at rest when they jumped.

The momentum of the person after they leave the floor is also given by p = mv, where m is the mass of the person and v is their velocity after jumping. We can use conservation of energy to find their velocity after jumping:

[tex]mgh = (1/2)mv^2[/tex]

Here g is the acceleration due to gravity, h is the height that the person jumps, and the factor of 1/2 comes from the fact that the person starts from rest. Solving for v, we get:

v = [tex]\sqrt{(2gh)}[/tex]

v = [tex]\sqrt{(2 * 9.8 * 0.149 m)}[/tex] ≈ 1.94 m/s

So the momentum of the person after leaving the floor is:

p = mv = (60.0 kg)(1.94 m/s) ≈ 116.4 kg m/s

(d) No, it doesn't make sense to say that the momentum came from the floor. Momentum is always conserved, so the person's momentum after jumping must be equal to their momentum before jumping. In this case, the person's momentum before jumping was zero.

(e) The kinetic energy of the person after leaving the floor is given by:

KE = [tex](1/2)mv^2[/tex], where m is the mass of the person and v is their velocity after jumping. Plugging in the given values, we get:

KE = [tex](1/2)(60.0 kg)(1.94 m/s)^2[/tex] ≈ 354 J

(f) No, it doesn't make sense to say that the energy came from the floor. Energy is always conserved, so the person's kinetic energy after jumping must be equal to the work done on them by external forces. In this case, the only external force doing work on the person is gravity.

Learn more about impulse visit: brainly.com/question/30395939

#SPJ4

The components of the nuclear submarine's velocity are approximately 23.8 km/h horizontally and 7.5 km/h vertically as it approaches the surface of the ocean at 25.0 km/h at an angle of 17.3°.

To find the components of the nuclear submarine's velocity as it approaches the surface of the ocean at 25.0 km/h at an angle of 17.3°, we will use trigonometry.

Step 1: Identify the angle and velocity
Angle = 17.3°
Velocity = 25.0 km/h

Step 2: Calculate the horizontal (x) component of velocity
Horizontal component (Vx) = Velocity * cos(Angle)
Vx = 25.0 km/h * cos(17.3°)

Step 3: Calculate the vertical (y) component of velocity
Vertical component (Vy) = Velocity * sin(Angle)
Vy = 25.0 km/h * sin(17.3°)

Step 4: Compute the values
Vx ≈ 25.0 km/h * 0.9537 ≈ 23.8 km/h
Vy ≈ 25.0 km/h * 0.2981 ≈ 7.5 km/h

Therefore, the components of the nuclear submarine's velocity are approximately 23.8 km/h horizontally and 7.5 km/h vertically as it approaches the surface of the ocean at 25.0 km/h at an angle of 17.3°.

Learn more about trigonometry : brainly.com/question/22698523

#SPJ11

It is true to say that the sun's dopplergram reveals our star's rotational and other physical characteristics.

As a wave source and its observer move in relation to one another, there is a shift in wave frequency known as the Doppler Effect. The finding was made by Christian Johann Doppler, who described it as the rising or falling of starlight based on the relative speed of the star.

Doppler effects exist for both light and sound. For instance, to determine how quickly an object is moving away from us, astronomers frequently measure how much a star or galaxy's light is "stretched" towards the lower frequency, red area of the spectrum.

To know more about rotational visit:-

https://brainly.com/question/12995374

#SPJ1

The second law of thermodynamics requires the work output of the engine to equal the difference in the quantities of heat taken in and released by the engine.

This law states that heat cannot flow from a colder body to a hotter body without the input of work. In the case of an engine, heat is taken in from the hot source, and some of that heat is converted into work output. The remaining heat is released to the cold source. The amount of work output must be equal to the difference in the quantities of heat taken in and released, according to the second law of thermodynamics. This is because the total amount of energy in a system is conserved, and energy cannot be created or destroyed. Therefore, the work output of the engine must balance the energy input and output in order to satisfy the laws of thermodynamics.

To learn more about work output https://brainly.com/question/30899925

#SPJ11

The initial downward acceleration of the electron relies on the strength of the magnetic field, which is not specified in the issue, and the acceleration's magnitude.

The proton is a stable subatomic particle with a rest mass of 1.67262 1027 kg, or 1,836 times the mass of an electron, and an equivalent positive charge to that of an electron.

Except for ordinary hydrogen, all atomic nuclei contain neutrons, which are neutral subatomic particles. Its rest mass, which is 1,838,68 times more than the electron's but only slightly higher than the proton's, is 1.67492749804 1027 kg. Electrically, it is not charged.

To know more about magnetic field visit:-

https://brainly.com/question/23096032

#SPJ1

The energy of a photon is given as 3.03×10−19 J/atom. The wavelength of the photon is 656 nm (option D).

The energy of a photon is given by the equation E = hc/λ, where h is Planck's constant (6.626 x 10^-34 J s), c is the speed of light (2.998 x 10^8 m/s), and λ is the wavelength of the photon. To find the wavelength of the photon, we can rearrange the equation to λ = hc/E. Substituting the given energy of the photon (3.03 x 10^-19 J/atom) into the equation gives a wavelength of 656 nm, which is option D in the given choices. Therefore, the correct answer is option D, and we can use the equation E = hc/λ to calculate the wavelength of a photon if we know its energy.

learn more about energy here:

https://brainly.com/question/1932868

#SPJ11

The amount of heat removed by the air-conditioner with a COP of 3.5 and consuming 16 kWh of electricity in a day is 56 kWh.

To find the heat removed, we use the formula: Heat Removed (Q) = COP x Electricity Consumed (E). The COP (Coefficient of Performance) is the ratio of the heat removed to the electricity consumed. In this case, the COP is 3.5, and the air-conditioner consumes 16 kWh of electricity during the day. Using the formula, we get:

Q = COP x E
Q = 3.5 x 16 kWh
Q = 56 kWh

So, the air-conditioner removes 56 kWh of heat during that day.

To know more about Coefficient of Performance click on below link:

https://brainly.com/question/31460559#

#SPJ11

The resonant angular frequency of the bound electrons is approximately 3.32 x 10¹⁵ rad/s.

The resonant angular frequency of the bound electrons can be calculated using the Lorentz model formula:

w = (Ne²/mεo) * [(Est - Eo)/(Est + 2Eo)]

where N is the atom density, e is the electron charge, m is the electron mass, εo is the permittivity of free space, Est is the static relative permittivity, and Eo is the high-frequency relative permittivity.

Substituting the given values:

w = (10²¹ * (1.6 x 10⁻¹⁹)²/(9.1 x 10⁻³¹* 8.85 x 10⁻¹²)) * [(9-6)/(9+2*6)]

w ≈ 3.32 x 10¹⁵rad/s

To know more about relative permittivity click on below link:

https://brainly.com/question/29288724#

#SPJ11