The HR department should install wheelchair ramps and widen the doorways as they don't want to loose an exceptional systems engineer who hopes to work at the techtonic group.
What is a wheelchair ramps?
A wheelchair ramp is an inclined plane that can be installed in addition to or instead of stairs. Ramps make it easier for wheelchair users, as well as people pushing strollers, carts, or other wheeled objects, to enter a building.
The Americans with Disabilities Act requires wheelchair ramps (or other ways for wheelchair users to access a building, such as a wheelchair lift) in new construction for public accommodations in the United States.
A wheelchair ramp can be fixed, semi-fixed, or portable. Permanent ramps are intended to be bolted or otherwise attached to the ground. Semi-permanent ramps are commonly used in the short term and rest on top of the ground or concrete pad.
To know more about wheelchair ramps, visit: https://brainly.com/question/17395685
#SPJ4
in a jfet, the u- shaped region is called the and is flush with the upper surface of the substrate.
The U-shaped area in a JFET is known as the channel and is flush with the substrate's upper surface.
The concept of a surface as it pertains to mathematics is called a surface. It is a generalization of a plane, just like a curve generalizes a straight line, but unlike a plane, it may be curved. There are a number of more precise definitions, depending on the circumstance and the mathematical techniques used for the study. Planes and spheres are the most fundamental mathematical surfaces in Euclidean 3-space. The specific description of a surface may vary depending on the circumstances. In topology or differential geometry, a surface rarely crosses itself. this is not the case in algebraic geometry. Since a surface is a two-dimensional topological space, a moving point on a surface can only travel in one of two directions.
Learn more about surface from
brainly.com/question/1297098
#SPJ4
technician a says that with a manual transmission, output shaft speed and torque can be increased at the same time. technician b says that output shaft speed and torque can be increased, but not at the same time. who is correct?
That is the purpose of a transmission in the first place, but output shaft speed and torque cannot be done at the same time. This is why shifters were created.
What is transmission in vehicle?
A transmission, also known as a gearbox, is the medium that transmits power generated by an engine to the wheels via a mechanical system of gears and gear trains in a car.
A transmission allows a person to control the application of power to a vehicle, without which the car would not move efficiently. Lower gears in a gearbox provide the necessary torque to accelerate, whereas higher gears aid in reaching high speeds by more effectively utilizing the engine's power.
While the function is straightforward, there are various transmissions that aid in the transmission of power.
To know more about transmission, visit: https://brainly.com/question/28449144
#SPJ4
7.41 two channels are welded to a rolled w section, as shown. determine the moments of inertia and the radii of gyration of the combined section with respect to the centroidal x and y axes.
When the two channels are welded to a rolled w section, the radius of gyration will be,
Radius of the gyration on the X-axis will be -
[tex]K_{X}[/tex] = 4 in
Radius of the gyration on the Y-axis will be -
[tex]K_{Y}[/tex] = 2.54 in
What is Radius of Gyration?
A body's radius of gyration, or gyradius, is always centered on an axis of rotation. It is defined as the spiral distance to a point with a moment of inertia. A rigid body's radius of gyration is a geometric property. Consider the center of mass. It is analogous to the body's actual mass dissemination. If the entire body's mass is concentrated.
In physics, the radius of gyration refers to the technique for dispersing various segments of the item present around an object in material science. The radius of gyration is the perpendicular distance taken from the rotational axis to an explicit point of mass when viewed in terms of the moment of inactivity.
To know more about Radius of Gyration, visit: https://brainly.com/question/15127397
#SPJ4
Why does some core analysis reports show depths broken into 1/2 feet and some in whole feet?
Answer:
Core analysis reports often show depths broken into increments of 1/2 feet because it provides a more detailed and accurate representation of the geologic layers present in the subsurface. By breaking the depth into smaller increments, geologists can more accurately depict the thickness and distribution of different geologic units and identify any changes or variations within those units. This can be especially important in cases where the geology is complex or there are small variations in the subsurface that could have significant impacts on the exploration or development of a resource.
In some cases, core analysis reports may show depths in whole feet rather than 1/2 feet. This is usually done when the geology is relatively simple and there are no significant variations within the geologic units being analyzed. In these cases, showing the depths in whole feet may be sufficient to accurately represent the geology and meet the needs of the project.
Ultimately, the decision to show depths in 1/2 feet or whole feet will depend on the specific needs of the project and the complexity of the geology being analyzed. Both approaches can be useful for different purposes and it is important to choose the one that is most appropriate for the task at hand.
1.) Unevenly torqued lug nuts could result in:
A. vibration while braking.
B. brake squeal.
C. premature brake pad wear.
D. pull to one side when braking.
Unevenly torqued lug nuts could result in premature brake pad wear. The correct option is C.
What are lug nuts?The hardware used to hold your wheel and tire assembly to your vehicle is known as lug nuts. The suitable lug nut guarantees that your wheel is installed safely and securely. They may be little, but they do a lot of work.
With a missing lug nut, you can drive at legal speeds; however, you should visit your nearest tire shop as soon as possible. Wheel nuts gradually loosen, causing wear on the wheel as it vibrates against the thread of the bolt.
Therefore, the correct option is C. premature brake pad wear.
To learn more about lug nuts, refer to the link:
https://brainly.com/question/20516510
#SPJ1
In a steel framed building Where floor loads and spans dictate, _ beams are used to support the floor instead of the lighter open web joists. _ joists are also sometimes used.Steel beamsLight gauge steel joists
Standard or "S" beams, wide flange or "W" beams, and pile or "H" beams are the three types of structural steel beams and girders that are available. Standard beams are designated by the letter S, the nominal web height in inches, the weight per foot in pounds, and finally the type of material.
A steel structure is what?
A steel structure is a metal building composed of solid structural steel pieces that are joined together to support loads. These buildings are dependable and use less raw materials than others, such as concrete, due to the high strength of steel.
What are the many types of steel structures?
In addition to L-beams, Z-shapes, HSS-shapes, L-shapes (angles), structural channels (C-beams, cross sections), T-shapes, rail profiles, bars, rods, and plates, structural steel also comes in a variety of shapes, including open joists made of web steel.
To know more about steel structures visit;
https://brainly.com/question/476531
#SPJ4
4. identify the c-h out-of-plane bending vibrations in the infrared spectrum of 4- methylcyclo- hexene. what structural information can be obtained from these bands?
650 to 1000 cm-1 of out-of-plane C-H bending vibrations.
The C-H stretch is where?Depending on the hydrization, the C-H stretching modes range between 2850 and 3300 cm-1. The peaks from 3000-3100 cm-1 denote an unsaturated system, while the range from 2850-3000 cm-1 refers to saturated systems (alkanes, sp3, for example 1). (alkenes, sp2, example 2; aromatic ring, example 3,4).
What does cyclohexane's IR spectrum look like?In the range of 4000-150 cm-1, the infrared spectra of cyclohexane in both its liquid and vapour phases have been investigated. The Eu skeletal deformation vibration's infrared band was discovered at 248 cm1.
To know more about vibrations visit:-
https://brainly.com/question/20999521
#SPJ4
Allow the connection to all programs, all protocols, and all ports with a scope of 192.168.0.0/24. This is an example of what type of security setting?
"Allow the connection" to all programs, all protocols, and all ports with a scope of 192.168.0.0/24 is an example of this type of security setting: ACL.
What is ACL?In Computer technology, ACL is an abbreviation for access control list and it can be defined as a security technique (setting) that is designed and developed to enable a computer system determine whether or not an end user has the minimum requirement, permissions, and credentials to access, use, or view the file(s) and folder resources that are stored on a computer.
This ultimately implies that, an access control list (ACL) is a security feature that can be implemented by using a firewall in order to help prevent or allow entry of an end user, who wishes to use a computer system.
Read more on access control here: brainly.com/question/3521353
#SPJ1
Complete Question:
An administrator navigates to the Windows Firewall with Advanced Security. The inbound rules show a custom rule, which assigned the action, "Allow the connection" to all programs, all protocols, and all ports with a scope of 192.168.0.0/24. This is an example of what type of security setting?
Accenture is helping a client improve their business agility by reducing time to
market, increasing product quality, and enabling continuous delivery.
The client team responsible for quality checks sometimes takes longer to finish
testing all aspects of their product.
What should Accenture suggest the client do to decrease the testing time?
Utilizing DevOps will help to lengthen the testing process, which improves business agility and raises the caliber of the final product.
What should Accenture suggest the client do to decrease the testing time?Deploying DevOps sooner during the testing process will shorten the testing period.The DevOps platform from Accenture is the best tool for helping teams and individuals choose, assess, develop, and simulate end-to-end testing solutions while also making the most of their time.Time must be used efficiently without losing quality inspections.Software delivery can be made more effective and efficient by interacting, coordinating, integrating, and automating between IT operations and software developers, according to the DevOps IT philosophy.To improve delivery predictability, efficiency, security, and maintainability, DevOps teams prioritize standardizing development environments and automating delivery processes.Automated testing ensures that the code is prepared for deployment.Once the code has passed all automated testing, it is made available to a select number of users.To learn more about Accenture refer
https://brainly.com/question/29509318
#SPJ1
in order to calculate the dispersion of contaminants in a room, one can use a large number of langrangian particles in a random process.TrueFalse
True. The dispersion of contaminants in a room can be modeled using a large number of Lagrangian particles in a random process. In this approach, the movement of each particle is tracked as it moves through the room, and the concentration of contaminants at different points in the room is calculated based on the distribution of the particles. This allows researchers to understand how the contaminants will spread throughout the room and how long they will remain in the air.
Lagrangian particle modeling is a useful tool for predicting the dispersion of contaminants in indoor environments, as it takes into account the influence of the room's geometry and the flow of air within the space. It can be used to evaluate the effectiveness of ventilation systems and to identify potential areas of high contaminant concentrations that may pose a risk to the occupants of the space.
Overall, the use of Lagrangian particles in a random process is a useful technique for understanding the dispersion of contaminants in indoor environments and for identifying strategies to reduce the risks associated with exposure to these contaminants.
Learn more about Lagrangian, here https://brainly.com/question/13195233
#SPJ4
how should water be added to a concrete mix
When adding water to a concrete mix, it is important to follow the manufacturer's instructions and use the right amount of water. Too little water can result in a dry, crumbly mix that is difficult to work with, while too much water can weaken the concrete and reduce its strength.
To add water to a concrete mix, follow these steps:
Begin by measuring out the amount of dry concrete mix that you need.Place the dry mix in a clean, dry mixing container, such as a wheelbarrow or cement mixer.Slowly add water to the dry mix, using a hose or watering can.Mix the water and dry mix together until the water is evenly distributed and the concrete reaches a uniform, smooth consistency.Continue to add small amounts of water as needed until the concrete reaches the desired consistency.Once you have added the desired amount of water, continue to mix the concrete for an additional 2-3 minutes to ensure that the water is evenly distributed and the concrete is properly mixed.It is important to note that the exact amount of water needed will vary depending on the type of concrete mix you are using, as well as the weather conditions and the intended use of the concrete. Therefore, it is important to follow the manufacturer's instructions and use the recommended amount of water.
A study was conducted to test the effectiveness of a juggling class. Before the class started, six subjects juggled as many balls as they could at once. After the class, the same six subjects juggled as many balls as they could. The differences in the number of balls are calculated. The differences have a normal distribution. Test at the 1% significance level. (Calculate "after" − "before. ")
There is sufficient evidence to support that juggling class is effective.
How to explain the normal distribution?From the information, a study was conducted to test the effectiveness of a juggling class and before the class started, six subjects juggled as many balls as they could at once
In this case, the standard deviation will be:
= ✓3.5 / n - 1
where b = number
= ✓3.5 / (6 - 1)
= ✓3.5/5
= 0.84
The test statistic will be:
t = d /(sd /✓n)
t = test statistic
sd = standard deviation
n = number
t = 1.5 / 0.84/✓6
t = 4.39
Here, the using a distribution table, the p value is 0.035.
Therefore, we reject the null hypothesis.
Learn more about normal distribution on:
brainly.com/question/4079902
#SPJ1
An environmental engineer wants to examine the permeability of different soils to determine the best natural containment system to protect groundwater from pollutants. The engineer tests four different soil samples, places them into a wet column, and pours 50mL of water over each sample. The engineer records the total amount of water that moves through the column as well as the total amount of time for the water to fully percolate through the soil. The data from the study are shown below.
Which of the following best describes why the engineer chose to calculate the permeability of the soil sample in the experimental design in order to evaluate a natural containment system to protect groundwater?
Note that the best option that describes why the engineer chose to calculate the permeability of the soil sample in the experimental design in order to evaluate a natural containment system to protect groundwater is: "Soils that have low permeability would best help protect groundwater because the soil traps pollutants so that chemical and biological breakdown can occur."
What is Soil Permeability?Soil permeability is a measure of how easily water can move through soil. Permeable soil allows water to pass through it easily, while impermeable soil does not allow water to pass through it easily.
Permeable soil is important because it helps to reduce flooding and erosion, and it can help to recharge groundwater. Impermeable soil can lead to problems such as flooding and erosion.
Permeability conveys information on foundation stability, seepage via embankments, and so on. Shear strength is the most essential geotechnical feature of soils, since it aids in the stability of civil engineering projects on or under the earth's surface.
Learn more about Soil Permeability:
https://brainly.com/question/27626099?
#SPJ1
Lamaellar eutectic solids form because the geometry limits diffusion distances required for solidification of alpha and beta phases. True False
Fals, Diffusion takes place across small distances due to the urgency of the phase shift, creating a fine lamellar microstructure.
The eutectic structure forms for what reason?A lamellar eutectic structure can only form if the interfacial energy between the two solids (S1/S2; S1 and S2 stand for Solid 1 and Solid 2, respectively) is lower than that of S1/Liquid and S2/Liquid. The diffusional partitioning of components results in the formation of eutectic microstructure.
What features distinguish a eutectic structure?A homogenous, solid mixture of two or more materials that forms a super-lattice is referred to as a eutectic system. The mixture either melts or solidifies at a lower temperature than the melting point of any of the constituent materials. The phrase is most frequently used to describe an alloy composition.
To know more about eutectic visit:-
https://brainly.com/question/27886492
#SPJ4
a synchronous motor rated at 300kva is to be added to the above load. it is expected to operate at 60% of rated load and an 80% leading power factor. find the total power factor and the real, reactive, and apparent power used by the facility.
The perceived power S is modest when the power factor is close to unity. This indicates that the electrical system's rating is the lowest possible for transmitting a specific active power P to the load.
What power factor and the real, and apparent power?The measurement of how much power is consumed to run machinery and equipment over a specific time period is known as apparent power, sometimes referred to as demand. You may calculate it by multiplying (kVA = V × A).
Therefore, working power (measured in kW) to perceived power (measured in kilovolt-amperes) is known as the power factor (PF) (kVA).
Learn more about power factor here:
https://brainly.com/question/17832655
#SPJ1
What is the current in a circuit if the voltage applied to a load is 492 volts? the connected load contains two series-connected resistive heating elements that are each rated for 2. 8 kw at 250 volts.
The current in the circuit would be approximately 10,958.33 A.
What is Ohm's law?Ohm's law states that the "current in a circuit is equal to the voltage applied to the circuit divided by the total resistance of the circuit".
To solve this problem, we need to first determine the total resistance of the two resistive heating elements in the circuit.
Since the heating elements are connected in series, their resistances add up, so the total resistance of the circuit is
⇒ 2 x 2.8 kW / 250 V = 11.2 kW / 250 V = 0.0448 kW / V.
As per Ohm's law, the current in the circuit would be
⇒ 492 V / 0.0448 kW / V = 10,958.33 A.
Therefore, the current in the circuit would be approximately 10,958.33 A.
To learn more about Ohm's law click here:
https://brainly.com/question/1247379
#SPJ2
The state of stress at a point consists of a major principal stress of 10,000 psf and a minor principal stress of 5,000 psf. The major principal stress acts in the vertical direction.
(a) Draw the Mohr's circle of stress and show the pole point (origin of planes).
(b) Determine the maximum shear stress.
(c) Determine the normal stress and shear stress on a plane that makes an angle of 60° with the minor principal plane.
The Maximum Shear Stress will be 7500 pst and
The Normal Stress on 60° with the minor principal plane will be 8750pst.
The Shear Stress on 60° with the minor principal plane will be 2165.063pst.
The answer to the Mohr's circle of stress is attached in this answer below.
What is Mohr's circle?
Mohr's circle is a crucial concept in Civil Engineering that is used in the domain of stress and strain. Mohr's circle depicts stress and strain at various planes for a stressed body in two dimensions. Mohr's circle is a concept used in soil mechanics and material strength to find stress and strains at different planes.
Mohr's circle is a collection of points that represent the magnitude of normal and shear stress at various planes in a stress element. Mohr's Circle can also be used to calculate the normal and shear strains of a plane strain system.
To know more about Mohr's circle, visit: https://brainly.com/question/18372020
#SPJ4
The data model contains the Official entity that has an array key called Reports of the type Report. The Report entity has a typekey field called ReportType (with possible typecodes 'inspection', 'state', 'police'). Given the variable: var thisOfficial : Official Which expression represents the correct approach to retrieve a single array element with ReportType 'police'? thisofficial. Reports.firstwhere(\r→r. ReportType=−ReportType.TC. POLICE) thisofficial.Reports. first(\->r.ReportType=wtypekey. ReportType.TC. POLICE) thisofficial. Reports.hasMatch(\r→rr. ReportType = a typelist. ReportType.TC POLICE) exists (report in thisofficial.Reports where report. Reporttype==typekey.ReportType.TC.POLICE) thisofficial. Reports". ReportType==ReportType. TC POLICE
The expression that represents the correct approach to retrieve a single array element with ReportType 'police' is:
thisOfficial.Reports.hasMatch(\ r -> r.ReportType == typelist.ReportType.TC_POLICE)
What is an array element?Information is stored in arrays. An array is made up of a group of elements used to store data. A scalar integer number called an index, which is assigned to each element in an array, is what makes up the indexing system.
The data size and the data type or data representation of an array's elements must be the same.
On the base address of the array is the first element.
To determine the element's position (or address), which is used to retrieve the element's actual value, three factors must be considered: the base address, the size of the data type, and the index.
Learn more about array
https://brainly.com/question/28565733
#SPJ4
A company stores products in a warehouse. Storage bins
in this warehouse are specified by their aisle, location
in the aisle, and shelf. There are 50 aisles, 85 horizontal
locations in each aisle, and 5 shelves throughout the warehouse. What is the least number of products the company
can have so that at least two products must be stored in
the same bin?
The least number of products the company can have so that at least two products must be stored in the same bin is 850.
What is LCM?The least common multiple, lowest common multiple, or smallest common multiple of two integers a and b, denoted by lcm in arithmetic and number theory, is the smallest positive integer that is divisible by both a and b.
The least common multiple (LCM) of two numbers is the smallest number that is divisible by both numbers. It can also be calculated for two or more numbers. There are several methods for calculating the LCM of a given set of numbers. One of the quickest ways to find the LCM of two numbers is to prime factorize each number, and then multiply the product of the highest powers of the common prime factors by the LCM of those numbers.
In this situation, since there are 50 aisles, 85 horizontal locations in each aisle, the lowest common multiple for 50 and 85 is 850.
Learn more about LCM on:
https://brainly.com/question/284493
#SPJ1
The circuit below is known as a source-follower configuration. It achieves a DC level shift between the input and output. The value of this shift is determined by the current lo. Assumey- 0.4, 2ion-0.6 V, To-0.43 V, k-1 15 pA/V2, and -0. The NMOS device has W/L 5.4/1.2u such that the short channel effects are not observed. a. Derive an expression giving Vi as a function of Vo and Vro. If we neglect body effect, what is the nominal value of the level shift performed by this circuit? The NMOS transistor experiences a shift in Vr due to the body effect. Find Vr as a function of Vo for Vo ranging from 0 to 1.5V with 0.25 V intervals. Plot a curve for VT vs. Vo roughly. b. DD 2.5 V 54112μ 10-35 μΑ
The nominal value of the level shift performed by this circuit is V[tex]_T[/tex] + 0.367 v, where given V[tex]_T[/tex] = 0.43.
The shift in voltage is, ΔV = 0.43 + 0.367 = 0.797.
What is voltage?Voltage is the pressure from the power source of an electrical circuit that pushes charged electrons (current) through a conducting loop, allowing them to perform tasks like lighting a lamp.
In a nutshell, voltage equals pressure and is measured in volts (V). The term honours Italian physicist Alessandro Volta (1745–1827), who developed the voltaic pile, the forerunner of the modern household battery.
Voltage was first referred to as electromotive force in the early history of electricity (emf). For this reason, voltage is denoted by the letter E in equations like Ohm's Law.
Learn more about Voltage
https://brainly.com/question/1176850
#SPJ4
the u.s. high-level significant weather prog, area 8, represents the a. height of maximum wind shear (53,000 feet). b. height of the tropopause. c. height of the jet stream (53,000 feet).
The peak of the tropopause is represented by area 8 of the United States High-Level Significant Weather Prog.
What does the important weather forecast chart look like?A map showing the expected weather forecast for a future date is called a prognostic chart. These graphs, which are produced by atmospheric models as a result of numerical weather prediction, include data on temperature, wind, precipitation, and weather fronts.
What can you infer from a low level significant weather chart?The Low-Level SWC, or Low-Level Significant Weather Chart, is a forecast chart used in general aviation for flight planning and preparation. It describes the climate in central Europe during a specific period of time. Areas with notable weather phenomena are therefore highlighted.
To know more about tropopause visit:-
https://brainly.com/question/11821902
#SPJ4
7. geophysical evidence suggests that lineaments in an exploration area may trend 60 degrees west. a. in order to enhance these lineaments, what are the two optimum radar look directions?
60 degrees east or west would be the two optimum radar look directions.
Why 60 degree?The optimum radar look directions for enhancing lineaments that trend 60 degrees west would be 60 degrees east and 60 degrees west.
This is because radar look directions are generally chosen to be perpendicular to the direction of the lineaments, as this allows the radar to "see" the lineaments more clearly and provide better resolution.
In this case, a look direction of 60 degrees east or west would be perpendicular to the lineaments, which would provide the best possible radar imaging of the lineaments in the exploration area.
To Know More About Geography, Check Out
https://brainly.com/question/1462956
#SPJ1
Suppose you are a part of Qatar''''s best software team named "the Photon Intelligence Team" and you are required to set up a detailed alert system to secure the data of all the football fans who are coming to watch football matches.
Metro trains are typically vacant during the day but may be busy at night.
What widespread interest from all throughout the world?But there were doubts about how it'd work in practice and how the city would handle the alleged influx of much more than a million images once the event started.
Michael Edgley, head of the Green and Gold Army, claimed that although some confusing transport management was presenting challenges for tour buses, it was a similar story for his traveling group of Socceroos family and supporters.
Because of the traffic restrictions, walking for fall and pick-ups around the stadiums can be difficult, but for numerous people, it is still the more convenient option.
To know more about the alleged influx visit:
https://brainly.com/question/14299924
#SPJ 1
20 Suppoe A Nonlinear Device I Available For Which The Output Current Io And Input Voltage V Are Related
Yes, such a divide could be used for demodulation. To generate AM wave with either carrier frequency Fc, we require a sinusoidal component of frequency FC to be added to the DSB-SC generated.
To achieve this requirement, we may use a configuration involving a pair of non-linear devices and a pair of identical bandpass filters as shown in the above figure.
From this spectrum, we see that in order to extract a DSB-SC wave with carrier frequency FC from i.
We need a bandpass filter with mid-band frequency Fc and band with 2w, the two of which satisfy the requirement FC-1 > fc/2 + 2w ⇒ 6w
To learn more about the output current
https://brainly.com/question/28132691
#SPJ4
technician a says liquid cooling an engine maintains a constant operating temperature. technician b says that air cooling lets the engine operate more efficiently. who is correct?
Technician A is correct. The liquid cooling an engine maintains a constant operating temperature. Technician B is wrong because the usage of air condition can increase fuel consumption by up to 20%.
Component of systems are a radiator to dissipate heat, a fan or fans to ensure adequate airflow for radiator cooling, a thermostat valve that opens when the desired operating temperature is reached and a water pump (or coolant pump) to circulate coolant through the engine, hoses and other elements. The engine cooling system has responsible for holding it at a stable temperature to avoid damage to the vehicle. There are two kind of cooling systems for engines:
Air cooling system. Water cooling system.Learn more about cooling engine system, here https://brainly.com/question/14557991
#SPJ4
T/F struct Info { int id; float cost; }; Given the struct above, the following code segment will correctly declare and initialize an instance of that struct. Info myInfo = {10,4.99}
The following code segment will properly declare and initialize an instance of the type mentioned above. Info myInfo = true; 10,4.99
A collection of symbols meant to signify established, frequently unspoken meanings; a system of symbols or signals used in communication. Code is text written in a programming language by a computer programmer. Examples include programming languages like C, C#, C++, Java, Perl, and PHP. Less formally, text written in markup or style languages like HTML and CSS can alternatively be referred to as "code." A code can be a list of guiding ideas. Our laws make up our legal system, and many people adhere to their own private "code of honour." Code can also refer to a language used to programme computers or a technique for transmitting encrypted messages. In 1303, the term "code" could only be used to describe a set of rules, such as as a code of conduct.
Learn more about code from
brainly.com/question/28008207
#SPJ4
technician a says synchronizers are used to match the clutch and input shaft speeds to provide easier gear changes. technician b says a synchronizer matches gear speed with shaft speed. who is correct?
Technician B is correct.
Since, a synchronizer matches gear speed with shaft speed.It is used for shifting gears while driving. The synchronizer works like a friction clutch, decelerating or accelerating the input shaft to match the speed of the next gear.
What is a synchronizer?
A synchronizer matches the rotational speed of the desired gear to the rotational speed of the output shaft. The gears are constantly meshing.
The shift fork moves the synchronizer's sleeve to lock the spinning gear to the shaft. It makes use of a blocking ring made of brass or soft metal to make contact with the gear's dog teeth.
These brass rings are inexpensive and wear over time, becoming rounded. When the teeth appear worn or rounded, they should be replaced.
The synchronizer blocking ring functions as a clutch, speeding up or slowing down the mating gear to match the output shaft speed.
To know more about Transmission, visit: https://brainly.com/question/27941416
#SPJ4
what is the lighting load on a 120v circuit for six 100w incandescent lights and four fluorescent fixtures with a ballast rating of 1.5a, all operating continuously for 8 hours per day?
Note that the lighting load on a 120v circuit for six 100w incandescent lights and four fluorescent fixtures with a ballast rating of 1.5a, all operating continuously for 8 hours per day is: 10,560 Watts.
What is Lighting Load?A building's lighting loads are sometimes referred to in terms of "Lighting Power Density," which is measured in watts per square foot or square meter.
It is to be noted that a single calculation is used to compute lighting load:
W=VA.
Where
W = Watts
V = Volts; and
A = Amps
To determine the total wattage for the fluorescent fixtures we say:
4 fixtures x 1.5 amps x 120 volts = 720 watts
Next, we add the wattages for the incandescent lights and fluorescent fixtures to get the total wattage for the circuit. That is:
(6 x 100watts) + 720 watts
= 600 watts + 720 watts
= 1,320 watts
Thus the Load is 1,320 watts.
If all lighting will operate continuously for 8 hours/day, then:
Daily energy consumption will be:
1320 x 8
= 10,560 Watts.
Thus, the Lighting Load on a 120v circuit for 6 100w incandescent lights and four fluorescent fixtures with a ballast rating of 1.5a Operating at 8 hours per day is 10,560 Watts.
Learn more about Lighting Load:
https://brainly.com/question/14375425
#SPJ1
If the input driver) gear is 30 teeth and the output (driven) gear is 15 teeth, what is the gear
ratio?
0.5 is the gear ratio of the gear having Input 30 teeth and output 15 teeth.
Gear Ratio is Defined as the ratio of the number of Output (driven) to input (Driver) .
Gear Ratio = output /input
The number of rotations of a driven gear to the number of rotations of a driver gear Which means if the gear ratio is 3 the Driven will rotate 3 time if Driver rotates 1 time.
Gear ratio=15/30 = 0.5
Hence 0.5 is the gear ratio of the gear having Input 30 teeth and output 15 teeth. Higher gear ratio will give the better torque and acceleration.
To study more about Gear:https://brainly.com/question/9302478
technician a says a torsion bar is a type of shock absorber. technician b says shock absorbers slow the upward and downward movement of the vehicle after a bump. who is correct?
A torsion isn't part of the shock absorber. Hence, technician A is wrong and technician B is correct.
The suspension system allows the wheel to up and down over bumps in the road. The suspension system makes the wheels and tires to up and down to absorb the shock from bumps. The rubber tires and air in the tires also slow down the ride over hard surfaces and conform to slightly uneven and rough surfaces. Thus, technician B is correct. Meanwhile, the technician A is wrong because a torsion isn't kind of shock absorber.
Kind of shock absorbers are:
Standard telescopic shocks. Struts. Spring seat.Learn more about shock absorbers, here https://brainly.com/question/10838031
#SPJ4