Answer: The resistance in the circuit is 250 ohms
Explanation:
According to Ohm's law:
[tex]V=IR[/tex]
where V = voltage = 55 V
I = current in Amperes = 0.22 A
R = Resistance = ?
Putting in the values we get:
[tex]55V=0.22A\times R[/tex]
[tex]R=250ohm[/tex]
Thus the resistance in the circuit is 250 ohms
a resistor dissipates 2.15 w when the rms voltage of the emf is 12.0 v .
At what rms voltage will the resistor dissipate 10.0 W?
The resistor will dissipate 10.0 W when the rms voltage of the emf is approximately 38.7 V.
To find the rms voltage at which the resistor dissipates 10.0 W, we can use the formula for power dissipation in a resistor:
P = (V^2) / R,
where P is the power dissipated, V is the rms voltage, and R is the resistance.
Given that the resistor dissipates 2.15 W at 12.0 V, we can rearrange the formula to find the resistance:
R = (V^2) / P.
Substituting the values, we have:
R = (12.0^2) / 2.15 = 67.16 Ω.
Now, we can use this resistance value and the desired power dissipation of 10.0 W to find the rms voltage:
V = sqrt(P * R).
Substituting the values, we get:
V = sqrt(10.0 * 67.16) = 38.7 V (approximately).
Therefore, the resistor will dissipate 10.0 W when the rms voltage of the emf is approximately 38.7 V.
To know more about voltage visit :
https://brainly.com/question/1176850
#SPJ11
In the following circuit, the switch has been in current position for a long time. Att-4s it moved to the second position. What is vt 10 5. In the following circuit, the switch has been in current position for a long time. At0 s switch is moved to the socond position. What is i(t) for all l0 80?
The value of i(t) for all t > 0 s when the switch is in position 2 is i(t) = (4/3)[15cos(12t) + 15sin(12t) - 10e^(-3t)] for all 10 < t < 80.
Since the switch has been in current position for a long time, there will be a steady-state response. Before the switch is moved to position 2, we can see that there is a voltage source of 10 V and a resistor of 5 Ω connected in series. Therefore, the current flowing through them will be 2 A (I = V/R).This current will remain the same when the switch is moved to position 2 since the circuit remains the same in that position. Hence, the value of vt at t = 0 s when the switch is moved to position 2 will be 10 V. So, the answer to the first part of the question is vt = 10 V.Now, the expression for i(t) for all t > 0 s when the switch is in position 2, We can see that there is a voltage source of 20 V and a resistor of 15 Ω connected in series. Therefore, the current flowing through them will be 4/3 A (I = V/R). This current will also flow through the 30 Ω resistor and the 80 mH inductor since they are connected in parallel to the 15 Ω resistor.Using Kirchhoff's current law at the node where the three resistors are connected, 4/3 = iR_1 + iR_2 + iR_3where i is the current flowing through the resistors R1, R2, and R3.Since,
R_1 = 15 Ω,
R_2 = 30 Ω,
R_3 = 80 mH,
Substituting their values,4/3 = i(15 + 30 + jω(0.08))
where ω is the angular frequency (ω = 2πf)
Rearranging the equation,i(15 + 30 + jω(0.08)) = 4/3
i = 4/3(15 + 30 + jω(0.08))^(-1)
i(t) = (4/3)(1/45 + 1/90 - jω(1/12))^{-1}
Taking the inverse Laplace transform of the above equation,i(t) = (4/3)[15cos(12t) + 15sin(12t) - 10e^(-3t)]
Hence, the value of i(t) for all t > 0 s when the switch is in position 2 is i(t) = (4/3)[15cos(12t) + 15sin(12t) - 10e^(-3t)] for all 10 < t < 80.
Learn more about the circuit:
brainly.com/question/2969220
#SPJ11
For the transistor circuit shown below, what is the value of the emitter current? Vcc = +20 V Rc 2.4 ΚΩ Vi. RB 510 ΚΩ 10 μF +|+ C₁ IB B VBE E - + + 10 μF HE C₂ VCE RE 1,5 ΚΩ + Vo B = = 100
The calculated value of the current will be IB = 2.9176 uA
KVL stands for Kirchhoff's Voltage Law. It is one of the fundamental laws in electrical circuit analysis, named after Gustav Kirchhoff, a German physicist.
Kirchhoff's Voltage Law states that the sum of the voltages around any closed loop in an electrical circuit is equal to zero. In other words, the algebraic sum of the voltage drops (or rises) in a closed loop must be equal to the sum of the voltage sources in that loop.
Apply kvl from collector to base to emitter loop.
-VCC +IB x RB + VBE + IE x RE=0
IE = (1+β)IB
-VCC +IB x RB+VBE+(1+β)IB x RE=0
-20+510k x IB+0.7+(101) x IB x 1.5K=0
IB = 2.9176 uA
To know more about KVL follow
https://brainly.com/question/31392023
#SPJ4
The missing circuit is attached below.
A mass of 347 g is attached to a spring and set into simple harmonic motion with a period of 0.316 s. If the total energy of the oscillating system is 6.54 J, determine the following. (a) maximum speed of the object m/s (b) force constant N/m (c) amplitude of the motion m
(a) The maximum speed of the object cannot be determined without knowing the amplitude of motion.
(b) The force constant of the system is approximately 133.75 N/m.
(c) The amplitude of the motion is approximately 0.312 m.
To determine the maximum speed, force constant, and amplitude of an object undergoing simple harmonic motion with a given mass, period, and total energy, we can use the equations and principles of harmonic motion.
(a) Maximum Speed:
The maximum speed (v_max) of an object undergoing simple harmonic motion is given by v_max = Aω, where A is the amplitude of motion and ω is the angular frequency. The angular frequency can be calculated using the formula ω = 2π/T, where T is the period.
ω = 2π / T = 2π / 0.316 s ≈ 19.87 rad/s
To find the maximum speed, we need the amplitude of motion. However, we don't have that information at the moment.
(b) Force Constant:
The force constant (k) of the spring can be determined using the formula k = mω², where m is the mass of the object and ω is the angular frequency.
m = 347 g = 0.347 kg
k = (0.347 kg)(19.87 rad/s)² ≈ 133.75 N/m
(c) Amplitude of Motion:
To find the amplitude of motion (A), we need the total energy (E) of the oscillating system. In simple harmonic motion, the total energy is given by the equation E = (1/2)kA².
6.54 J = (1/2)(133.75 N/m)A²
Solving for A, we find:
A² = (2 * 6.54 J) / 133.75 N/m
A² ≈ 0.0975 m²
Taking the square root:
A ≈ √0.0975 m² ≈ 0.312 m
Learn more about speed:
https://brainly.com/question/13943409
#SPJ11
What is the overall energy transformation in a coal-fired power plant?
1.electrical to chemical
2.chemical to electrical
3.nuclear to radiant
4.radiant to nuclear
The overall energy transformation that occurs in a coal-fired power plant is 2. chemical to electrical. The energy transformation in a coal-fired power plant is used to generate electrical energy from thermal energy. The energy that is transformed comes from the chemical potential energy stored in coal.
The chemical energy is converted into thermal energy, which is then converted into mechanical energy that drives a generator. The overall process involves the combustion of coal in a furnace, which generates heat energy. This heat energy is then transferred to the water that is present in the boiler. The water is converted into steam due to the heat energy and this steam is used to turn the turbines. The turbines convert the thermal energy into mechanical energy, which is then used to drive the generator. The generator then converts the mechanical energy into electrical energy.
Therefore, the energy transformation that occurs in a coal-fired power plant is from chemical potential energy in coal to thermal energy, then to mechanical energy, and finally to electrical energy. The correct option is (2).
To know more about energy transformation visit:
https://brainly.com/question/29102331
#SPJ11
A car traveling with an initial velocity of 27 m/s slows down at a constant rate of 5.4 m/s2 for 3 seconds. What is its velocity at the end of this time? The velocity of the car at the end of 3 seconds is m/s.
If a car going at 27 meters/seconds slows down at a steady pace of 5.4 meters/seconds for three seconds, the final velocity is 43.2 m/s.
Newton provided three equations of motion.
v = u + a × t
S = u × t + 1/2 × a × t.t
v² - u² = 2 × a × s
As stated in the problem, a car driving at an initial velocity(u) of 27 meters/seconds slows down at a constant rate of 5.4 meters/seconds² for 3 seconds.
Using the second equation of motion,
S = u × t + 1/2 × a × t²
= 27 × 3 + 0.5 × 5.4 × 3²
= 81 + 24.3
= 105.3
Now, using the third equation of motion,
v² - 27² = 2 × 5.4 × 105.3
v² - 729 = 1137.24
v² = 1137.24 + 729
v² = 1,866.24
v = √1,866.24
= 43.2 m/s
Thus, the car's velocity at the end of three seconds would be 43.2 m/s.
To know more about final velocity:
https://brainly.com/question/9909784
#SPJ4
saturn has a satellite called enceladus. enceladus is just a little over 500 km in diameter. what shape do you expect enceladus to be?\
Saturn has a satellite called enceladus, enceladus is just a little over 500 km in diameter, the shape enceladus to be round or spherical shape
Saturn is one of the most fascinating planets in our solar system, and it has many satellites. Enceladus is one of these satellites, and it has a diameter of just over 500 km. Based on this information, it is reasonable to assume that Enceladus is a round or spherical shape. However, it's not quite as simple as that. Enceladus is indeed round, but it has not formed into a perfectly spherical shape, it has some noticeable irregularities, which is due to its composition.
Enceladus is made up of a rocky core with a water ice crust and an icy mantle, because of this, it has different densities, which have resulted in some significant variations in its shape. Enceladus is a very intriguing satellite because of its many peculiar features, it has active water geysers that have been observed shooting out from its south pole, and it has a subsurface ocean that may contain the necessary conditions to support life. This makes Enceladus an excellent target for further study and exploration. So therefore Enceladus shape is a round or spherical shape.
To know more about Enceladus visit:
https://brainly.com/question/31646213
#SPJ11
The electrostatic force between two positive point charges is F when the charges are 0.1 meter apart. When these point charges are placed 0.05 meter apart, the electrostatic force between them is...
A) A F and repelling
B) 1/4F and repelling
C) 4F and attracting
D) 1/4F and attracting
The new electrostatic force when the charges are 0.05 meters apart will be 4F.
Hence, the correct option is C.
The electrostatic force between two point charges is inversely proportional to the square of the distance between them. This relationship is described by Coulomb's Law:
F = k * (|q1 * q2|) / [tex]r^{2}[/tex]
Where:
F is the electrostatic force.
k is the electrostatic constant, approximately equal to [tex]8.988 * 10^9 N m^2/C^2.[/tex]
|q1 * q2| is the product of the magnitudes of the two charges.
r is the distance between the charges.
Let's consider the given scenario. When the charges are initially placed 0.1 meters apart, the electrostatic force is F. Now, when the charges are moved to a distance of 0.05 meters apart, we can calculate the new electrostatic force using the information provided.
According to Coulomb's Law, if we decrease the distance between the charges by a factor of 2, the force between them will increase by a factor of [tex]2^{2}[/tex] = 4.
Therefore, the new electrostatic force when the charges are 0.05 meters apart will be 4F.
The correct answer is option C) 4F and attracting.
Hence, the correct option is C.
To know more about electrostatic force here
https://brainly.com/question/30333838
#SPJ4
the _____ exerts the largest gravitational force on the earth, and the _____ exerts the largest tidal force on the earth.
The sun exerts the largest gravitational force on the Earth, and the moon exerts the largest tidal force on the Earth.
The sun, being the largest celestial body in our solar system, exerts the largest gravitational force on the Earth. This force is responsible for keeping the Earth in its orbit around the sun and contributes significantly to the stability of our solar system. The gravitational force of the sun also affects the tides on Earth, but its influence is relatively smaller compared to the moon.
The moon, despite being much smaller than the sun, exerts the largest tidal force on the Earth. Tides are the result of the gravitational interaction between the moon and the Earth. The moon's gravitational force creates tidal bulges on the Earth's oceans, leading to the regular rise and fall of the tides.
The gravitational pull of the moon causes the water closest to it to experience a stronger force, resulting in high tide, while the water on the opposite side experiences a weaker force, leading to low tide.
Learn more about gravitational force here:
https://brainly.com/question/29190673
#SPJ11
Conservation of Linear Momentum and Impulse --- Momentum Theorem Objectives 1. To verify the conservation of momentum for fully elastic and totally inelastic collisions; 2. To verify the Impulse-Momentum Theorem. Introduction and Background For a body of mass m moving with velocity v, its linear momentum p is defined as (1) p = mv According to the law of conservation of momentum, linear momentum p of a system may change only if there is a net external force acting on this system. In other words momentum of a system is conserved when there is no net external force acting on it.
The conservation of linear momentum states that linear momentum of a system remains conserved unless there is a net external force acting on it. This conservation law is applicable for both fully elastic and totally inelastic collisions. Similarly, the Impulse-Momentum Theorem states that the impulse of a force is equal to the change in momentum of the object it is acting on.
Linear momentum p is defined as (1) p = mv, where m is the mass of the body and v is its velocity. The momentum of a system only changes when there is a net external force acting on it. The conservation of momentum is applicable to both fully elastic and totally inelastic collisions.
The impulse-momentum theorem is defined as FΔt = Δp, where F is the force acting on an object, Δt is the duration for which the force acts, and Δp is the change in momentum of the object. The impulse-momentum theorem is applicable in all situations where the force acting on the object is not constant.
Know more about linear momentum, here:
https://brainly.com/question/30767107
#SPJ11
Steam passes steadily through a turbine and condenser as shown in the figure below. After expanding through the turbine and producing 1000kW of power, the steam is at a pressure of 0.08 bar and a quality of 874: It enters a shell-and-tube heat exchanger where the steam now condenses on the outside of tubes through which cooling water flows, this condensate continues to flow, finally exiting as saturated liquid at 0.08 bar. The mass flow rate of the condensing steam is 58kg/s. In order to condense the steam, cooling water enters the tubes at 15" and flows as a separate stream to exit at 35°C with negligible change in pressure. Stray heat transfer is negligible as are kinetic and potential effects. Considering the steam inside the turbine as a system, is the system best described as open, closed, or isolated? What is the mass flow rate of steam entering the turbine in kg/s? What is the enthalpy at the inlet of the turbine in kJ/kg? What is the mass flowrate of the cooling water in kg/s? If the diameter of the cooling water line is 10cm, what is the velocity of the cooling water in m/s when it enters the condenser? A 100kW pump is available to transfer the condensate to a storage tank (Le, the magnitude of Wdot_in is 100kW). What would be the maximum increase in height in meters that the pump could move the water assuming that the temperature, pressure, and velocity of the condensate are roughly equal at the inlet and outlet of the pump section?
The system can be best described as an open system. The mass flow rate of steam entering the turbine is 58 kg/s. The enthalpy at the inlet of the turbine is not provided in the information provided.
Based on the given information, the system is best described as an open system because steam enters and exits the system while interacting with its surroundings.
The mass flow rate of the steam entering the turbine is given as 58 kg/s.
The enthalpy at the inlet of the turbine is not provided in the information given. It would require additional data, such as the specific enthalpy of the steam at the given conditions, to calculate the enthalpy.
The mass flow rate of the cooling water is not provided in the information given. Without the mass flow rate, it is not possible to calculate the velocity of the cooling water when it enters the condenser.
The maximum increase in height that the pump could move the water cannot be determined without additional information. The given information does not provide the necessary data, such as the pressure difference across the pump or the pump efficiency, to calculate the maximum increase in height.
Overall, additional information is needed to provide specific answers to the questions about enthalpy, cooling water mass flow rate, power cooling water velocity, and the maximum increase in height that the pump could achieve.
Learn more about power here
https://brainly.com/question/17283457
#SPJ11
A sample of radioactive technetium-99 of half-life 6 h is to be used in a clinical examination. The sample is delayed 11.5 h before arriving at the lab for use.
What fraction of radioactive technetium remains.
Express your answer using three significant figures.
N/No = __________.
N/No = 0.170
Radioactive decay is the process in which unstable atomic nuclei lose energy or mass by emitting radiation, such as alpha particles, beta particles, and gamma rays. The rate at which this occurs is known as the decay rate, which is determined by the half-life of the radioactive element. Half-life is the time it takes for half of the nuclei of a radioactive sample to decay. For the given sample of radioactive technetium-99, the half-life is 6 h. This means that after 6 hours, half of the original sample will have decayed, and after 12 hours, three-quarters of the original sample will have decayed. Since the sample is delayed by 11.5 hours before arriving at the lab, we can calculate the fraction of the sample that remains: N/No = (1/2)^(11.5/6) = 0.170 (to three significant figures) Therefore, the fraction of the sample that remains is 0.170.
Technetium is a radioactive silver-gray metal with the chemical symbol Tc. It happens normally in tiny sums in the world's covering, yet is basically man-made. Technetium-99 is created during atomic reactor activity, and is a side-effect of atomic weapons blasts.
Know more about radioactive technetium, here:
https://brainly.com/question/10323748
#SPJ11
An amoeba is 0.305 cm away from the 0.300 cm focal length objective lens of a microscope. (a) What is the image distance (in cm) for this configuration? (b) What is this image's magnification? An eyepiece with a 2.2 cm focal length is placed 19.78 cm from the objective. (c) What is the image distance for the eyepiece in cm? d_i, e = 6.373 0% deduction per feedback. (d) What magnification is produced by the eyepiece? (e) What is the overall magnification?
(a) The distance is 18.18 cm. (b) The magnification is 59.71. (c) The distance for the eyepiece is 2.08 cm. (d) The magnification produced by the eyepiece is 0.0548. (e) The overall magnification is 3.27.
(a) The image distance for the configuration can be calculated using the lens formula:
1/f = 1/v - 1/u
where:
f = focal length of the lens (0.300 cm)
v = image distance
u = object distance (0.305 cm)
Since the object is located beyond the focal length of the objective lens (u > f), the image will be formed on the same side as the object and will be virtual. The equation can be rearranged as:
1/v = 1/f - 1/u
Substituting the values:
1/v = 1/0.300 - 1/0.305
Calculating:
1/v ≈ 3.333 - 3.278
1/v ≈ 0.055
Taking the reciprocal of both sides:
v ≈ 1/0.055
v ≈ 18.18 cm
Therefore, the image distance for this configuration is approximately 18.18 cm.
(b) The magnification of the image formed by the objective lens can be calculated using the formula:
magnification = v/u
Substituting the values:
magnification = 18.18/0.305
magnification ≈ 59.71
Therefore, the magnification of the image formed by the objective lens is approximately 59.71.
(c) To calculate the image distance for the eyepiece, we need to consider the combined system formed by the objective lens and the eyepiece. The image formed by the objective lens serves as the object for the eyepiece. We can use the lens formula again:
1/f = 1/v' - 1/u'
where:
f = focal length of the eyepiece (2.2 cm)
v' = image distance for the eyepiece
u' = object distance for the eyepiece (distance between the objective lens and the eyepiece)
Given that the object distance (u') is the sum of the image distance produced by the objective lens and the distance between the objective and the eyepiece:
u' = v + d
Substituting the values:
u' = 18.18 + 19.78
u' ≈ 37.96 cm
Now we can use the lens formula to find v':
1/f = 1/v' - 1/u'
1/2.2 = 1/v' - 1/37.96
Calculating:
1/v' = 0.4545 + 0.0263
1/v' ≈ 0.4808
Taking the reciprocal of both sides:
v' ≈ 1/0.4808
v' ≈ 2.08 cm
Therefore, the image distance for the eyepiece is approximately 2.08 cm.
(d) The magnification produced by the eyepiece can be calculated using the formula:
magnification = v'/u'
Substituting the values:
magnification = 2.08/37.96
magnification ≈ 0.0548
Therefore, the magnification produced by the eyepiece is approximately 0.0548.
(e) The overall magnification of the microscope system can be obtained by multiplying the magnifications of the objective lens and the eyepiece:
overall magnification = magnification (objective) × magnification (eyepiece)
Substituting the values:
overall magnification ≈ 59.71 × 0.0548
overall magnification ≈ 3.27
Therefore, the overall magnification of the microscope system is approximately 3.27.
(a) The image distance for this configuration is approximately 18.18 cm.
(b) The magnification of the image formed by the objective lens is approximately 59.71.
(c) The image distance for the eyepiece is approximately 2.08 cm.
(d) The magnification produced by the eyepiece is approximately 0.0548.
(e) The overall magnification of the microscope system is approximately 3.27.
To learn more about magnification, visit
https://brainly.com/question/3480304
#SPJ11
when the two asteroids collide, they stick together. based on your graph in part c, determine the velocity of the new megaasteroid.
Two asteroids collide head-on and stick together. Before the collision, asteroid A (mass 1,000 kg) moved at 100 m/s, and asteroid B (mass 2,000 kg) moved at 80 m/s in the opposite direction. The velocity of the asteroids after the collision is 20 m/s in the direction of asteroid B.
According to momentum conservation, the total momentum before the collision should be equal to the total momentum after the collision.
Total momentum before collision = Total momentum after collision
(m₁ * v₁) + (m₂ * v₂) = (m₁ * v₁') + (m₂ * v₂')
Substituting the given values into the equation:
(1,000 kg * 100 m/s) + (2,000 kg * (-80 m/s)) = (1,000 kg * v) + (2,000 kg * v)
Simplifying the equation:
100,000 kg m/s - 160,000 kg m/s = 3,000 kg v
-60,000 kg m/s = 3,000 kg v
Dividing both sides by 3,000 kg:
-20 m/s = v
The negative sign indicates that the velocity is in the opposite direction compared to the initial velocities of the asteroids. Therefore, the velocity of the asteroids after the collision is -20 m/s or 20 m/s in the direction of asteroid B.
To know more about collide here
https://brainly.com/question/27993473
#SPJ4
The question is incomplete, the complete question is:
Two asteroids collide head-on and stick together. Before the collision, asteroid A (mass 1,000 kg) moved at 100 m/s, and asteroid B (mass 2,000 kg) moved at 80 m/s in the opposite direction. Use momentum conservation (make a complete Momentum Chart) to find the velocity of the asteroids after the collision?
Learning Goal To practice Problem-Solving Strategy 27.2 Motion in Magnetic Fields. EVALUATE your answer An electron inside of a television tube moves with a speed of 2.56x107 m/s. It encounters a region with a uniform magnetic field oriented perpendicular to its trajectory. The electron begins to move along a circular arc of radius 0.190 m. What is the magnitude of the magnetic field? Part C Calculate the magnitude F of the force exerted on the electron by a magnetic field of magnitude 8.27x10^-4 T oriented as described in the problem introduction. Express your answer in newtons
The magnitude of the magnetic field is 0.090 T. The magnitude of the force exerted on the electron by the magnetic field is 2.09 x 10⁻¹³N.
To find the magnitude of the magnetic field, we can use the formula for the magnetic force experienced by a charged particle moving in a magnetic field.
The magnetic force (F) acting on a charged particle can be calculated using the formula:
F = q * v * B * sin(θ)
where:
F is the force,
q is the charge of the particle (in this case, the charge of an electron, which is 1.6 x 10^(-19) C),
v is the velocity of the particle,
B is the magnitude of the magnetic field, and
θ is the angle between the velocity vector and the magnetic field vector (90 degrees in this case).
We are given the velocity of the electron (v = 2.56 x 10⁷m/s) and the radius of the circular arc (r = 0.190 m).
Since the electron is moving in a circular arc, the magnetic force provides the necessary centripetal force to keep the electron in its circular path.
The centripetal force (Fc) can be calculated using the formula:
Fc = (m * v²) / r
where m is the mass of the electron (9.11 x 10⁻³¹kg).
Since the magnetic force and the centripetal force are equal, we can set up an equation:
q * v * B = (m * v²) / r
Solving for B, we get:
B = (m * v) / (q * r)
Substituting the known values:
B = (9.11 x 10⁻³¹ kg * 2.56 x 10⁷ m/s) / (1.6 x 10⁻¹⁹ C * 0.190 m)
Calculating the value, we find:
B ≈ 0.090 T
Therefore, the magnitude of the magnetic field is approximately 0.090 T.
To calculate the magnitude of the force (F) exerted on the electron, we can use the same formula:
F = q * v * B * sin(θ)
Substituting the given values:
F = (1.6 x 10⁻¹⁹ C) * (2.56 x 10⁷ m/s) * (8.27 x 10⁻⁴ T) * sin(90°)
Calculating the value, we find:
F ≈ 2.09 x 10⁻¹³ N
Therefore, the magnitude of the force exerted on the electron by the magnetic field is approximately 2.09 x 10⁻¹³ N.
The magnitude of the magnetic field is 0.090 T, and the magnitude of the force exerted on the electron by the magnetic field is 2.09 x 10⁻¹³N.
To know more about force visit:
https://brainly.com/question/25239010
#SPJ11
Select the measurement most likely to be subject to random error. 1 - Measuring temperature with a digital thermometer 2- Measuring temperature with a mercury thermometer 3- Measuring a distance in yards by pacing 4-Determining the number of pennies in bags by dividing the weights of the filled bags by the legally defined weight of a penny O A. Measuring a distance in yards by pacing O B. Measuring temperature with a digital thermometer OC. Measuring temperature with a mercury thermometer O D. Determining the number of pennies in bags by dividing the weights of the filled bags by the legally defined weight of a penny
Therefore, option A, measuring a distance in yards by pacing, is the measurement most likely to be subject to random error.
Option A—pacing a yard—is more likely to have random mistake. Pacing requires estimate and counting steps, which introduces random error. Stride length, step size owing to weariness or uneven terrain, and miscounting steps all contribute to measurement uncertainty and error.
Pacing lacks the precision and reliability of calibrated instruments, unlike the other methods. Digital and mercury thermometers (options B and C) are designed to detect temperature accurately with little random error. Option D, which uses a standardised weight and mathematical computation to count pennies in bags, decreases random errors.
To know more about random errors
https://brainly.com/question/30779771
#SPJ4
Two rectangular loops of wire lie in the same plane as shown in the figure below. If the current I in the outer loop is counterclockwise and increases with time, what is true of the current induced in the inner loop? (Select all that apply.)'
It is zero.
It is clockwise.
It is counterclockwise.
Its magnitude depends on the dimensions of the loops.
Its direction depends on the dimensions of the loops.
The current induced in the inner loop is counterclockwise. Its magnitude depends on the dimensions of the loops, and its direction is determined by the right-hand rule.
According to Faraday's law of electromagnetic induction, a changing magnetic field can induce an electromotive force (emf) in a closed loop of wire. The magnitude and direction of the induced current depend on the rate of change of magnetic flux through the loop.
In the given scenario, the current in the outer loop is counterclockwise and increasing with time. As the current increases, the magnetic field produced by the outer loop also strengthens. This changing magnetic field penetrates the inner loop.
By the right-hand rule, when the fingers of your right hand curl in the direction of the magnetic field lines passing through the inner loop (due to the outer loop), the thumb points in the direction of the induced current. In this case, the thumb points counterclockwise, indicating that the induced current in the inner loop is counterclockwise.
The magnitude of the induced current depends on the rate of change of magnetic flux and the properties of the loops, such as their dimensions. A larger rate of change of flux or different loop dimensions would result in a different magnitude of the induced current.
The direction of the induced current is determined by the right-hand rule and the orientation of the magnetic field lines. It does not depend on the dimensions of the loops but rather on the relative orientation and the changing magnetic field.
Based on the given information, the current induced in the inner loop is counterclockwise. The magnitude of the induced current depends on the rate of change of magnetic flux and the dimensions of the loops, while its direction is determined by the right-hand rule and the orientation of the magnetic field.
To know more about right-hand rule, visit
https://brainly.com/question/14434299
#SPJ11
you pull yourself through the snow a distance of 510 meters with a horizontal force of 240 newtons. how much work did you do?
You did 122,400 Joules of work. Work is a measure of energy transfer, and in this case, it represents the energy you exerted to move yourself through the snow by applying a horizontal force.
Work is defined as the product of force and displacement in the direction of the force. In this scenario, you are pulling yourself through the snow with a horizontal force of 240 Newtons over a distance of 510 meters.
To calculate the work done, you multiply the force applied (240 N) by the distance moved in the direction of the force (510 m):
Work = Force × Distance
Work = 240 N × 510 m
Work = 122,400 Joules
Therefore, you did 122,400 Joules of work. Work is a measure of energy transfer, and in this case, it represents the energy you exerted to move yourself through the snow by applying a horizontal force.
To know more about force, refer here:
https://brainly.com/question/30526425#
#SPJ11
calculate k fror a hexagonal lattice of 1.4 cm radius natural uranium rods and graphite if the lattice pitch is 20cm
The k-factor for the hexagonal lattice of 1.4 cm radius natural uranium rods and graphite, with a lattice pitch of 20 cm, is approximately 0.907.
To calculate the k-factor for a hexagonal lattice of uranium rods and graphite, we need to determine the number of uranium rods within a given area and the total area of the unit cell.
1. First, let's calculate the area of the hexagonal unit cell:
The lattice pitch is given as 20 cm, which is the distance between the centers of adjacent uranium rods.
The radius of the uranium rods is 1.4 cm, so the distance between their centers is twice the radius, which is 2.8 cm.
The distance between the centers of the graphite rods will also be 2.8 cm.
Now, we can calculate the area of the hexagonal unit cell using the formula:
Area = (3√3/2) * (distance between centers)^2
Area = (3√3/2) * (2.8 cm)^2
Area ≈ 21.2 cm^2
2. Next, we need to determine the number of uranium rods within the unit cell.
The hexagonal lattice arrangement allows for 1 uranium rod at the center and 6 uranium rods surrounding it.
Total number of uranium rods in the unit cell = 1 (center) + 6 (surrounding) = 7 rods
3. Finally, we can calculate the k-factor using the formula:
k = (1 - (ρ_graphite/ρ_uranium)) * (Number of uranium rods/Area)
The density of uranium (ρ_uranium) is approximately 19.1 g/cm^3.
The density of graphite (ρ_graphite) is approximately 2.26 g/cm^3.
k = (1 - (2.26 g/cm^3 / 19.1 g/cm^3)) * (7 rods / 21.2 cm^2)
k ≈ 0.907
Therefore, the k-factor for the hexagonal lattice of 1.4 cm radius natural uranium rods and graphite, with a lattice pitch of 20 cm, is approximately 0.907.
To learn more about Lattice click here
https://brainly.com/question/2497050
#SPJ11
A 100-turn, 5.0-cm-diameter coil is at rest with its axis vertical. A uniform magnetic field 60∘ away from vertical increases from 0.50 T to 2.5 T in 0.70 s .
Part A
What is the induced emf in the coil?
Express your answer with the appropriate units.
The induced emf in the 100-turn, 5.0-cm-diameter coil, resulting from a uniform magnetic field increasing from 0.50 T to 2.5 T in 0.70 s at a 60° angle from vertical, is 3.4 V.
Determine what is the induced emf in the coil?The induced emf in a coil can be calculated using Faraday's law of electromagnetic induction, which states that the emf is equal to the rate of change of magnetic flux through the coil.
The magnetic flux through a coil can be determined by multiplying the magnetic field strength by the area of the coil and the cosine of the angle between the magnetic field and the normal to the coil.
In this case, the coil has 100 turns, a diameter of 5.0 cm (radius = 2.5 cm = 0.025 m), and the magnetic field increases from 0.50 T to 2.5 T. The angle between the magnetic field and the normal to the coil is 60°.
To calculate the induced emf, we first need to find the change in magnetic flux. The initial magnetic flux is given by Φ₁ = B₁Acosθ, and the final magnetic flux is Φ₂ = B₂Acosθ, where B₁ and B₂ are the initial and final magnetic field strengths, A is the area of the coil, and θ is the angle between the magnetic field and the normal to the coil. The change in magnetic flux is then ΔΦ = Φ₂ - Φ₁.
The area of the coil can be calculated as A = πr², where r is the radius of the coil. Plugging in the values, we have A = π(0.025 m)².
The change in magnetic flux is ΔΦ = (2.5 T)(π(0.025 m)²cos60°) - (0.50 T)(π(0.025 m)²cos60°).
Next, we need to calculate the rate of change of magnetic flux, which is ΔΦ/Δt, where Δt is the time interval. Plugging in the given values, we have Δt = 0.70 s.
Finally, the induced emf is given by the rate of change of magnetic flux, so we have emf = ΔΦ/Δt.
Evaluating the expression, we get emf = [(2.5 T)(π(0.025 m)²cos60°) - (0.50 T)(π(0.025 m)²cos60°)] / (0.70 s).
Calculating the numerical value, we find emf ≈ 3.4 V.
To know more about induced emf, refer here:
https://brainly.com/question/30891425#
#SPJ4
An earth satelite moves in a circular orbit at a speed of 5500 m/s
Part A
What is its orbital period?
Express your answer in hours to two significant figures.
The orbital period of the Earth satellite is approximately 1.34 hours, expressed to two significant figures.
To find the orbital period of an Earth satellite moving in a circular orbit, we can use the relationship between the orbital speed (v) and the orbital period (T).
The orbital speed is given as 5500 m/s.
The formula to calculate the orbital period is:
T = (2πr) / v
Where r represents the radius of the orbit.
In a circular orbit, the radius (r) is equal to the distance between the center of the Earth and the satellite.
Assuming the satellite is in a low Earth orbit, we can approximate the radius of the orbit as the sum of the radius of the Earth (approximately 6371 km) and the altitude of the satellite.
Converting the altitude to meters, let's assume it is 300 km, which is 300,000 meters.
Substituting the values into the formula, we have:
T = (2π(6371 km + 300 km)) / 5500 m/s
T = (2π(6671000 m)) / 5500 m/s
T ≈ 4820 seconds
To convert the orbital period to hours, we divide by 3600 seconds (1 hour = 3600 seconds):
T ≈ 4820 seconds / 3600 seconds/hour ≈ 1.34 hours
Learn more about satellite:
https://brainly.com/question/18496962
#SPJ11
a microscope has a 11.0 × eyepiece and a 59.0 × objective lens 20.0 cm apart. assume a normal eye and that the final image is at infinity. Calculate the focal length of the objective lens. Where the object must be for a normal relaxed eye to see it in focus?
The focal length of the objective lens is approximately 3.73 cm. The object must be placed at a distance of 15.9 cm in front of the objective lens for a normal relaxed eye to see it in focus.
To find the focal length of the objective lens, we can use the magnification formula for a compound microscope:
magnification = (-fe / fo) × (1 + de / do)
Where fe is the focal length of the eyepiece, fo is the focal length of the objective lens, de is the distance between the eyepiece and the final image, and do is the distance between the object and the objective lens.
Given that the eyepiece has a magnification of 11.0x and the objective lens has a magnification of 59.0x, and assuming the final image is at infinity, we can set the magnification formula equal to the total magnification:
11.0 × 59.0 = (-fe / fo) × (1 + ∞ / do)
Since the final image is at infinity, the term (∞ / do) becomes negligible and can be approximated as zero:
11.0 × 59.0 ≈ -fe / fo
Simplifying the equation, we find:
fo ≈ -fe / (11.0 × 59.0)
Substituting the given value of fe = 11.0x, we can calculate the focal length of the objective lens (fo).
Next, to find the distance where the object must be placed for a normal relaxed eye to see it in focus, we can use the thin lens equation:
1 / f = 1 / do + 1 / di
Where f is the focal length of the objective lens, do is the distance between the object and the objective lens, and di is the distance between the objective lens and the final image (which is at infinity).
Since the final image is at infinity, the term 1 / di becomes negligible and can be approximated as zero:
1 / f ≈ 1 / do
Simplifying the equation, we find:
do ≈ f
Substituting the calculated value of f, we can find the distance where the object must be placed for a normal relaxed eye to see it in focus (do).
The focal length of the objective lens is approximately 3.73 cm. To see the object in focus with a normal relaxed eye, the object must be placed at a distance of 15.9 cm in front of the objective lens.
To know more about Focal Length, visit
https://brainly.com/question/28039799
#SPJ11
Two thin parallel slits that are 0.0118 mm apart are illuminated by a laser beam of wavelength 555 nm.
(a) On a very large distant screen, what is the total number of bright fringes (those indicating complete constructive interference), including the central fringe and those on both sides of it? Solve this problem without calculating all the angles! (Hint: What is the largest that sin ? can be? What does this tell you is the largest value of m?)
(b) At what angle, relative to the original direction of the beam, will the fringe that is most distant from the central bright fringe occur?
(a) The total number of bright fringes, including the central fringe and those on both sides of it, is 42.
(b) The fringe that is most distant from the central bright fringe occurs at an angle of 90 degrees relative to the original direction of the beam.
Determine how to find the total number of bright fringes?(a) The total number of bright fringes, including the central fringe and those on both sides of it, is given by the formula:
Number of fringes = (2d) / λ
where d is the separation between the slits and λ is the wavelength of the laser beam.
In this case, the separation between the slits is 0.0118 mm (or 0.0118 × 10⁻³ m) and the wavelength of the laser beam is 555 nm (or 555 × 10⁻⁹ m).
Number of fringes = (2 × 0.0118 × 10⁻³ m) / (555 × 10⁻⁹ m) = 42
Therefore, the total number of bright fringes is 42.
The formula for the number of fringes takes into account the separation between the slits (d) and the wavelength of the light (λ). By substituting the given values into the formula, we can calculate the total number of bright fringes.
The formula assumes that the screen is at a very large distance from the slits, resulting in a pattern of alternating bright and dark fringes. The number of fringes can be determined without calculating the angles directly by using the formula.
Determine the fringe at most distant from the central bright fringe occur?(b) The fringe that is most distant from the central bright fringe occurs when the angle between the original direction of the beam and the direction of the fringe is at its maximum. This occurs when the angle of diffraction (θ) is maximum, which corresponds to the first minimum of the diffraction pattern.
For small angles, the angle of diffraction (θ) can be approximated as:
θ ≈ (mλ) / d
where m is the order of the fringe (m = 1 for the first minimum), λ is the wavelength of the laser beam, and d is the separation between the slits.
To find the angle at which the fringe is most distant from the central bright fringe, we need to find the maximum value of θ. This occurs when sinθ is maximum, which happens when θ = 90°. At this angle, sinθ = 1.
Therefore, the largest value of sinθ is 1, which gives us the largest value of m. In this case, m = 1.
The angle of diffraction (θ) determines the position of the fringes in the diffraction pattern. The first minimum (dark fringe) occurs when the angle of diffraction is at its maximum. By using the approximation formula for small angles, we can calculate the angle at which the fringe is most distant from the central bright fringe.
The largest value of sinθ is 1, which corresponds to the angle of 90°. This angle gives us the largest value of m, indicating the fringe that is most distant from the central bright fringe.
To know more about diffraction, refer here:
https://brainly.com/question/12290582#
#SPJ4
Consider the torque-free rotational motion of an axisymmetric rigid body with J1= 2J2 = 2J3. a) Analytically find the largest possible value of the angle between w and H. (Hint: Write the angular momentum vector in the body coordinate frame {b1, b2, b3} and consider the angular momentum magnitude H = H fixed.) Ans. Omax = 19.47° (show that this is the maximum!) b) Find the critical value of rotational kinetic energy that results in the largest angle between w(omega) and H. Also, find the minimum and maximum rotational kinetic energies. Express your an- swer in terms of H and J2
The largest possible value of the angle between w and H is 19.47°, which occurs when the rotational kinetic energy is at its maximum.
The critical value of rotational kinetic energy that results in the largest angle between w and H is the maximum rotational kinetic energy, and the minimum and maximum rotational kinetic energies are directly proportional to J₂ and w².
What is rotational kinetic energy?
Rotational kinetic energy refers to the energy associated with the rotational motion of an object. It is a form of kinetic energy that arises from the rotational motion of an object around an axis.
The inertia tensor can be written as:
J = diag(J₁, J₂, J₂)
Given that J₁ = 2J₂ = 2J₃, we have:
J = diag(2J₂, J₂, J₂)
The magnitude of the angular momentum vector H is given by H = |L| = √(L · L). Since H is fixed, its magnitude remains constant throughout the motion.
Now, we can write the magnitude of the angular momentum vector H in terms of J₂ and w as:
H = √(L · L) = √((2J₂w₁)² + (J₂w₂)² + (J₂w₃)²)
Simplifying:
H² = 4J₂²w₁² + J₂²w₂² + J₂²w₃²
H² = J₂²(4w₁² + w₂² + w₃²)
Since H is fixed, we can rewrite the equation as:
4w₁² + w₂² + w₃² = constant
The magnitude of the angular velocity vector w is given by w = √(w₁² + w₂² + w₃²). So, we can rewrite the equation as:
4w₁² + (w - w₁)² = constant
Expanding and simplifying:
5w₁² - 2ww₁ + w² = constant
This equation represents a quadratic equation in terms of w₁. For a quadratic equation, the maximum or minimum occurs at the vertex of the parabolic curve. In this case, we want to find the maximum value of w₁.
To find the maximum value of w₁, we can take the derivative of the equation with respect to w₁ and set it to zero:
d/dw₁ (5w₁² - 2ww₁ + w²) = 0
10w₁ - 2w = 0
w₁ = w/5
Now, substituting this value of w₁ back into the equation, we get:
5(w/5)² - 2w(w/5) + w² = constant
w²/5 + w²/5 + w² = constant
7w²/5 = constant
Therefore, the maximum angle between w and H occurs when 7w²/5 is at its maximum value, which happens when w² is at its maximum. Since w is the magnitude of the angular velocity vector, the maximum value of w² occurs when the rotational kinetic energy is at its maximum.
Hence, the critical value of rotational kinetic energy that results in the largest angle between w and H is when the rotational kinetic energy is at its maximum.
To find the minimum and maximum rotational kinetic energies, we can use the relationship between rotational kinetic energy (T) and the inertia tensor (J):
T = (1/2) w · J · w
Substituting the inertia tensor J = diag(2J₂, J₂, J₂) and simplifying:
T = (1/2)(2J₂w₁² + J₂w₂² + J₂w₃²)
T = J₂(w₁² + w₂² + w₃²)
Since w = √(w₁² + w₂² + w₃²), we can rewrite the equation as:
T = J₂w²
Therefore, the rotational kinetic energy (T) is directly proportional to the square of the angular velocity magnitude (w²) and the inertia tensor component J₂.
To learn more about rotational kinetic energy,
https://brainly.com/question/30459585
#SPJ4
what three factors affect the torque created by a force relative to a specific pivot point
The three factors that affect torque are the magnitude of the force, the distance from the pivot point, and the angle between the force and the lever arm.
The three factors that affect the torque created by a force relative to a specific pivot point are:
1. Magnitude of the Force: The greater the magnitude of the applied force, the greater the torque generated. A larger force will create a larger rotational effect around the pivot point.
2. Distance from the Pivot Point: The distance between the pivot point and the point where the force is applied, known as the lever arm or moment arm, influences the torque. Increasing the lever arm increases the torque for the same applied force.
3. Angle of Application: The angle at which the force is applied relative to the lever arm also affects the torque. The torque is maximized when the force is applied perpendicular (at a 90-degree angle) to the lever arm.
These factors demonstrate how the interaction between force, distance, and angle determines the rotational effect (torque) around a specific pivot point.
To know more about torque, click here https://brainly.com/question/30338175
#SPJ11
3. a primitive optical microscope, intended for visual observation, is constructed with a 75 mm objective lens and a 150 mm eyepiece. the microscope is used for viewing an object at a distance of 125 mm from the objective. calculate the magnification m1 of the microscope, assuming an accommodation of 250 mm.
The magnification of the microscope (m1) is 0.5. To calculate the magnification of the microscope, we can use the formula:
Magnification (m1) = (focal length of the objective lens) / (focal length of the eyepiece)
Given that the focal length of the objective lens is 75 mm and the focal length of the eyepiece is 150 mm, we can substitute these values into the formula: m1 = 75 mm / 150 mm, m1 = 0.5
Therefore, the magnification of the microscope (m1) is 0.5.
The magnification of 0.5 means that the image seen through the microscope appears half the size of the actual object. So, objects viewed through this microscope will appear magnified, but not significantly so.
The accommodation of 250 mm is not directly used in calculating the magnification but may affect the viewer's ability to focus and perceive the magnified image clearly.
To know more about focal length, refer here:
https://brainly.com/question/2194024#
#SPJ11
In Parts A and B you found two different expressions to describe the allowed electron velocities v. Equate these two values (eliminating v) and solve for the allowable radii r in the Bohr model. The two equations are:v =e sqrt(4phie0mr) and v = nh/2mrphi
To solve for the allowable radii in the Bohr's model by equating the expressions for electron velocities, we'll set the two equations equal to each other: e√(4πε₀mr) = (nh)/(2mrΦ)
Where:
e is the elementary charge [tex](1.602 * 10^{-19} C)[/tex]ε₀ is the vacuum permittivity ([tex]8.854 * 10^{-12[/tex] C²/(N·m²))m is the mass of the electron [tex](9.109 * 10^{-31} kg)[/tex]r is the radius of the orbitn is the principal quantum number (an integer representing the energy level)h is Planck's constant [tex](6.626 * 10^{-34} J.s)[/tex]Φ is a constant related to the electrostatic potential energy
To simplify the equation, let's square both sides:
(e√(4πε₀mr))² = ((nh)/(2mrΦ))²
Simplifying further:
e²(4πε₀mr) = (nh)²/(4m²r²Φ²)
Now, we can rearrange the equation to solve for r:
4πε₀me²r = nh²/(4m²Φ²r²)
Multiply both sides by (4m²Φ²r²):
4πε₀me²r³ = nh²
Finally, solve for r:
r³ = nh²/(4πε₀me²)
Taking the cube root of both sides:
r = ∛(nh²/(4πε₀me²))
This expression gives the allowable radii (r) in the Bohr model when equating the two expressions for electron velocities.
To learn more about Bohr's model visit:
brainly.com/question/3964366
#SPJ11
A Carnot engine operates between a hot reservoir at 370.0 K and a cold reservoir at 293.0 K. If it absorbs 455.0 J of heat per cycle at the hot reservoir, how much work per cycle does it deliver? If the same engine, working in reverse, functions as a refrigerator between the same two reservoirs, how much work per cycle must be supplied to remove 910.0 J of heat from the cold reservoir?
The Carnot engine delivers 168.16 J when operating between the hot reservoir at 370.0 K and the cold reservoir at 293.0 K. When working in reverse, 168.16 J must be supplied to remove 910.0 J of heat.
To determine the work per cycle delivered by the Carnot engine, we can use the formula for the efficiency of a Carnot engine:
Efficiency = 1 - (Tc/Th),
where Tc is the temperature of the cold reservoir and Th is the temperature of the hot reservoir.
Given:
Tc = 293.0 K (temperature of the cold reservoir)
Th = 370.0 K (temperature of the hot reservoir)
Qh = 455.0 J (heat absorbed per cycle at the hot reservoir)
First, we calculate the efficiency of the Carnot engine:
Efficiency = 1 - (293.0/370.0) = 1 - 0.7918918919 ≈ 0.2081081081.
The efficiency of the Carnot engine is approximately 0.2081.
The work done by the engine per cycle is given by:
W = Efficiency * Qh = 0.2081 * 455.0 = 94.5435 J.
Therefore, the Carnot engine delivers approximately 94.5435 J of work per cycle when operating between the given temperatures.
When the same engine functions as a refrigerator in reverse, the work per cycle supplied can be calculated using the same efficiency formula:
Efficiency = 1 - (Tc/Th),
where Tc is the temperature of the cold reservoir and Th is the temperature of the hot reservoir.
Given:
Tc = 293.0 K (temperature of the cold reservoir)
Th = 370.0 K (temperature of the hot reservoir)
Qc = 910.0 J (heat removed per cycle from the cold reservoir)
To find the work supplied (W), we rearrange the efficiency formula:
Efficiency = 1 - (Tc/Th) ⇒ Tc/Th = 1 - Efficiency,
Tc/Th = 1 - 0.2081 = 0.7919.
We can use the equation:
Efficiency = W/Qc ⇒ W = Efficiency * Qc,
W = 0.7919 * 910.0 = 719.979 J.
Therefore, when functioning as a refrigerator, approximately 719.979 J of work per cycle must be supplied to remove 910.0 J of heat from the cold reservoir.
The Carnot engine delivers 168.16 J of work per cycle when operating between the hot reservoir at 370.0 K and the cold reservoir at 293.0 K. When working in reverse as a refrigerator, 168.16 J of work per cycle must be supplied to remove 910.0 J of heat from the cold reservoir.
To learn more about Carnot, visit
https://brainly.com/question/28104112
#SPJ11
it takes four hydrogen nuclei to create one helium nucleus in the proton–proton chain, which is the main energy source of the sun. if a single hydrogen nucleus ha
In the proton-proton chain reaction, it takes four hydrogen nuclei (protons) to create one helium nucleus in the Sun's main energy source. This process releases a tremendous amount of energy.
The proton-proton chain reaction is the primary mechanism through which the Sun generates energy. It involves a series of nuclear reactions that convert hydrogen nuclei (protons) into helium nuclei. In the first step, two protons combine to form a deuterium nucleus (a proton and a neutron) through a process called nuclear fusion. This step releases a positron and a neutrino.
In the second step, a proton and the deuterium nucleus combine to form a helium-3 nucleus, emitting a gamma ray in the process. Finally, two helium-3 nuclei collide to produce a helium-4 nucleus and two additional protons. This last step releases two protons, two neutrinos, and a significant amount of energy.
Overall, it takes four hydrogen nuclei (protons) to create one helium nucleus in the proton-proton chain reaction. The release of energy from this process powers the Sun and provides heat helium nucleus and light to our solar system.
Learn more about helium nucleus here
https://brainly.com/question/31674543
#SPJ11
A kinetics experiment is performed to determine the activation energy of a reaction. The following data were collected in the experiment:
Experiment Temperature, °C k, M- 15-1 1 130.2 0.00363 2 24.8 0.00109
Calculate 1/T in K-1 for the temperature in Experiment 1.
Calculate 1/T in K-1 for the temperature in Experiment 2.
Calculate ln(k) for the rate constant in Experiment 1.
Calculate ln(k) for the rate constant in Experiment 2
The linear relationship is between ln(k) and 1/T. Calculate the slope (in K) between the points (1/T,ln(k)).
Calculate the activation energy of the reaction in J/mol.
Calculate the activation energy of the reaction in kJ/mol.
Calculate the rate constant, k, for this reaction at 300.0°C.
1/T in Experiment 1 = 0.002480 K⁻¹, 1/T in Experiment 2 = 0.003341 K⁻¹, ln(k) in Experiment 1 = -5.614, ln(k) in Experiment 2 = -6.919, the slope (in K) between the points (1/T, ln(k)) = -1513K, the activation energy of the reaction 12577.582 J/mol, and the rate constant is 0.0720 M⁻¹.
Given:
Experiment 1:
Temperature = 130.2 °C
k = 0.00363 M⁻¹
Experiment 2:
Temperature = 24.8 °C
k = 0.00109 M⁻¹
Step 1: Convert temperature in Experiment 1 from °C to K
T₁ = 130.2 + 273.15 = 403.35 K
Step 2: Convert temperature in Experiment 2 from °C to K
T₂ = 24.8 + 273.15 = 298.95 K
Step 3: Calculate 1/T in K⁻¹ for the temperature in Experiment 1
1/T₂ = 1/403.35 = 0.002480 K⁻¹
Step 4: Calculate 1/T in K⁻¹ for the temperature in Experiment 2
1/T₂ = 1/298.95 = 0.003341 K⁻¹
Step 5: Calculate ln(k) for the rate constant in Experiment 1
ln(k₁) = ln(0.00363) = -5.614
Step 6: Calculate ln(k) for the rate constant in Experiment 2
ln(k₂) = ln(0.00109) = -6.919
Step 7: Calculate the slope (in K) between the points (1/T, ln(k))
slope = (ln(k₂) - ln(k1)) / (1/T₂ - 1/T₁)
= (-6.919 - (-5.614)) / (0.003341 - 0.002480)
= -1.305 / 0.000861
= -1513 K
Step 8: Calculate the activation energy of the reaction in J/mol
slope = -Ea / R
-1513 = -Ea / (8.314 J/(mol·K))
Ea = 1513 × 8.314 J/mol
Ea = 12577.582 J/mol
Step 9: Calculate the activation energy of the reaction in kJ/mol
Ea kJ = Ea / 1000
Ea kJ = 12.577582 kJ/mol
Step 10: Calculate the rate constant, k, for this reaction at 300.0 °C
T₃ = 300.0 + 273.15 = 573.15 K
1/T₃ = 1/573.15 = 0.001742 K⁻¹
k₃ = exp(slope × (1/T3))
k₃ = exp(-1513 × 0.001742)
k₃ = exp(-2.634986)
k₃ = 0.0720 M⁻¹
To learn more about the rate constant, follow the link:
https://brainly.com/question/20305922
#SPJ4