The amount of work done by the hairdryer is equal to 450 Kilojoules.
Given the following data:
Time = 600 secondsPower = 750 wattTo determine the amount of work done by the hairdryer:
Mathematically, the work done by an object with respect to power and time is given by the formula:
[tex]Work\;done = power \times time[/tex]
Substituting the given parameters into the formula, we have;
[tex]Work\;done = 750 \times 600[/tex]
Work done = 450,000 Joules
Note: 1000 Joules = 1 Kilojoules.
Work done = 450 Kilojoules.
Read more: https://brainly.com/question/13818347
If the speed of the magnet is doubled, the induced voltage is ________ . twice as great four times as great half as great unchanged
If the speed of the magnet is doubled, the induced voltage is twice as great
Faraday's law of induction states that whenever relative motion exists between a coil and magnetic field, a voltage will induce in the circuit and this voltage is proportional to the rate of change of the flux. The expression for the motional emf is as follows:
ε=Blv
Here, ε is the motional emf, B is the magnetic field, l is the length of the conductor, and v is the velocity at which the magnetic field changes.
The induced voltage by the moving magnet is directly proportional to the speed of the magnet. Therefore, an increase in the speed of the magnet will increase the induced voltage.
If the speed of the magnet is doubled, the induced voltage is twice as great
Find out more at: https://brainly.com/question/13369951
A wire that is 1.0 m long with a mass of 90 g is under a tension of 710 N. When a transverse wave travels on the wire, its wavelength is 0.10 m. What is the frequency of this wave?
Answer:
890 HzI hope you liked my answer. Thank You!
1. 1. are the charged parts of an atom.
a. Only electrons
b. Only protons
c. Neutrons only
d. Electrons and neutrons
e. Electrons and protons
f. Protons and neutrons
Answer:
e. Electrons and protons
Explanation:
Which of the following changes would decrease the force between two charged particles by a factor of 9? A. Decreasing the distance between the particles by a factor of 3 B. Increasing the distance between the particles by a factor of 3 C. Increasing the amount of charge on each particle by a factor of 9 D. Decreasing the amount of charge on one of the particles by a factor of 3
Option B is correct.Increasing the distance between the particles by a factor of 3 decrease the force between two charged particles by a factor of 9.
What is electric force?The electric force between the two charges is directly proportional to the product of the charge and inversely proportional to the square of the distance between them.
The electric force is found as;
[tex]\rm F = \frac{K q_1q_2}{r^2}[/tex]
The electric force between the two charges is directly proportional to the product of the charge.
The electric force is inversely proportional to the square of the distance between them.
Increasing the distance between the particles by a factor of 3 decreases the force between two charged particles by a factor of 9
Hence, option B is correct.
To learn more about the electric force, refer to the link;
https://brainly.com/question/1076352
#SPJ2
A textbook weighs 34 N on the surface of the Earth. What is the book’s mass on Earth’s surface?
Answer:
About 3.47kg
Explanation:
Recall that weight is equal to mass times acceleration.
In this case, our acceleration is due to gravity which on earth is about 9.8m/s/s
So we have 34N=9.8 *mass, divide both sides by 9.8 we get mass is equal to about 3.47kg.
Select the correct answer. Chloe is playing the flute some distance away from a crowd. If the atmospheric temperature is 15°C, what is the speed of the sound traveling from the flute? A. 340 meters/second B. 330 meters/second C. 320 meters/second D. 310 meters/second E. 300 meters/second
Answer:
A. 340 meters/second
I think this is the right answer.
What is the significance of Isaac's name? What is the significance of Isaac's name?
Answer:
Isaac is one of the three patriarchs of the Israelites and is an important figure in the Abrahamic religions, including Judaism, Christianity, and Islam. Isaac's name means "he will laugh", reflecting the laughter, in disbelief, of Abraham and Sarah, when told by God that they would have a child.Hope this helps !!Explanation:
Itz Deepika Here to help ~ .
Note:- If you have more questions then let me know !!
when a student comned his dry hair for a long time, his hair began to stand up. Which of these has MOST LIKELY happened
His hair got charged due to continuous friction causing them to get attracted to other objects and thus standing up.
Answer:The comb and hair have become charged with opposite charges.
Explanation:When a comb is run through your hair charges pass between your hair and the comb, so the comb becomes charged either positively or negatively, and the hair oppositely charged. When the comb is brought close to paper an opposite charge is induced in the paper, and the opposite charges attract.
Can someone help me solve this problems please? It's a physics problem.
Answer:
i cant see
Explanation:
but im smart
a uniform thin rod of length l and mass m is allowed to rotate on a frictionless pin passing through one end. The rod is released from rest in the horizontal position. a.) What is the speed of the center of gravity when the rod reaches its lowest position? b.) What is the tangential speed of the lowest point of the rod when the rod reaches its lowest position?
Answer:
Explanation:
Potential energy gets converted to rotational kinetic energy
a) ½Iω² = mgh
½(mL²/3)ω² = mgL/2
(L/3)ω² = g
ω = [tex]\sqrt{3g/L}[/tex]
v(CG) = (L/2) [tex]\sqrt{3g/L}[/tex]
Not sure if you wanted angular speed or tangential speed of the CG so I gave both.
b) v = Rω = L [tex]\sqrt{3g/L}[/tex]
How much work is done on a 30 kg object when 20 Newton’s of force is exerted for a distance of 5 meters
Answer:
Work = force * displacement
= 50 N * 20 Meter
=1000 Newton meter = 1000 joule .
Explanation:
I need help with parts a and B of this question
Answer:
Explanation:
Let x be the leaf spring compression distance
F = kx
5.20 x 10⁵ = (5.45 x 10⁵)x + (3.80 x 10⁵)(x - 0.500)
5.20 x 10⁵ = (5.45 x 10⁵)x + (3.80 x 10⁵)(x) - 1.90 x 10⁵
7.10 x 10⁵ = (9.25 x 10⁵)x
x = 0.76756...
x = 0.768 m
W = ½(5.45 x 10⁵)0.768² + ½(3.80 x 10⁵)(0.768 - 0.500)²
W = 174,148.648648...
W = 174 KJ
How do you measure a English saddle to fit your horses?
Answer:
measure the area in which the rider will sit on, then take those measurements to a person who crafts saddles, tell them the exact measurements. then you wait a while until he/she is done then put the saddle on the horse.
Explanation:
Answer:
Explanation:
The shape of the horse's withers is also a determining factor in choosing a saddle. An adjustable hoop saddle allows you to choose with finesse the opening of the tree at the height of the withers, in order to best adapt to each horse. It is the size of the arch that determines the opening of the saddle.
English saddles are the main riding saddles used in equestrian disciplines around the world: Show jumping, endurance, require specific designs to meet specific needs. For example, dressage saddles are designed to bring the rider closer to the horse, allowing him to communicate very precisely with his horse.
A gold fish weighing 13g has a speed of 8.8m/s. What is its Kinetic energy
Answer:
0.47 J
Explanation:
Help on 9 and 10!!!!!! I’ll give 5 starts
Answer: part a is e
part b a
Explanation:
I HOPE THIS HELPS
A body with a uniform acceleration travels distances of 24m and 64m during the first two equal consecutive intervals of time, each of duration 4s. Determine the initial velocity and acceleration of the moving body.
Answer:
Explanation:
Average velocity in the 24 m interval is 24 / 4 = 6 m/s
Average velocity in the 64 m interval is 64 / 4 = 16 m/s
There is a 4 second interval between the two points where average velocity equals actual velocity
a = Δv/t = (vf - vi) / t = (16 - 6) / 4 = 2.5 m/s²
s = v₀t + ½at²
24 = v₀(4) + ½(2.5)4²
4v₀ = 24 - 20
v₀ = 1 m/s
Not asked for but the velocity at the end of the first segment and beginning of the second segment is 11 m/s and final velocity is 21 m/s
A block of wood
wood, with mass 1.34 kg rests stationary
on horizontal ground.
The coefficient of Kinetic
friction between the block and the ground is 0.966.
A bullet, with mass 0.250kg, moving horizontally
hits and sticks into the block of wood. We find
that the speed of the block of wood, with the
ballet embedded in it, just after collision is 11.9 m/s.
A) calculate the speed of the bullet before hitting the block of wood.
it, just after the collision
is 11-9mis.
as calculate the speed of the bullet before
s
hitting the block of wood.
Answer:
Explanation:
conservation of momentum
m(u) + M(0) = (m + M)v
u = (m + M)v/m
u = (0.250 + 1.35)(11.9) / 0.250
u = 76.16
u = 76.2 m/s
That's a fairly massive, and slow, bullet.
A woman skis from rest down a hill 20 m high. If friction is negligible, what is her speed at the bottom of the slope? Select one: O a. 20 m/s O b. 12 m/s O c. 400 m/s O d. 6 m/s
Hi there!
We can use the work-energy theorem to solve.
Recall:
[tex]\large\boxed{E_i = E_f}}[/tex]
Initial energy = final energy
The initial energy is purely potential (she starts from rest), and, if we assign the bottom of the slope as the 0 line, her energy at the bottom is purely kinetic.
PE = mgh
KE = 1/2mv²
We can begin by setting the two equal:
mgh = 1/2mv²
Cancel out the mass and rearrange to solve for velocity:
2gh = v²
v = √2gh
Plug in given values and use g ≈ 10 m/s²:
v = √2(10)(20) = 20 m/s
. Boa constrictor snakes have tiny pelvic girdles and leg bones within their bodies. Since these structures are not functional, they are called *
a. vestigial
b. analogous
c. maladaptive
d. homologous
Those organic structures that do not seem to play any important biological function in the organism that possesses them are known as vestigial structures.
What is a vestigial structure?A vestigial structure is one that has atrophied or lost its original function throughout the course of evolution.
It generally refers to those organic structures that were useful at some point, but are now practically or totally useless.These structures are preserved as an inheritance of the evolutionary process, because at some point an ancestor of the current species had that structure, which was functional, but it ceased to be important and would end up atrophy.Therefore, we can conclude that vestigial structures are structures that some organisms still conserve as an inheritance from their ancestors but that, for some reason or another, are no longer useful for the functioning of the same.
Learn more about vestigial structures here: https://brainly.com/question/2141655
A 1.2 kg hammer slams down on a nail at 5.0 m/s and bounces off at 1.0 m/s. If the impact lasts 1.0 ms, what average force is exerted on the nail?
Answer:
Explanation:
Impulse results in a change of momentum
FΔt = mΔV
F = mΔV/Δt
The impulse acting on the hammer will equal the impulse acting on the nail
If we assume upward is the positive direction
F = m(vf - vi)/t
F = 1.2(1.0 - (-1.5)) / 0.001
F = 3000 N
A 1.2 kg hammer slams down on a nail at 5.0 m/s and bounces off at 1.0 m/s, if the impact lasts 1.0 ms, so the average force exerted on the nail is 3000 N.
What is average force?According to Newton's third law, there is an equal and opposite force for every force. The hammer's force on the nail will be identical in size to the nail's force on the hammer, but opposite in direction.
Momentum shifts as a result of impulse.
FΔt = mΔV
F = mΔV/Δt
The force exerted on the hammer will be equivalent to the force exerted on the nail.
m(vf - vi)/t = F
F = 1.2(1.0 - (-1.5)) / 0.001
F = 3000 N
Therefore, F = 3000 N, if A 1.2 kg hammer slams down on a nail at 5.0 m/s and bounces off at 1.0 m/s, if the impact lasts 1.0 ms.
Learn more about force, here:
https://brainly.com/question/20038742
#SPJ2
a spring with a spring constant of 65 n/m is displaced -94cm. what is the magnitude of the force exerted by the spring
Answer:
Explanation:
F = kx = 65 N/m(0.94 m) = 61.1 = 61 N
HELP PLEASE WILL MARK BRAINLIEST
Outside wooden steps may get slippery when they are wet. How could you make them less slippery?
There are many ways you can get wooden steps to be less slippery even when they are wet. Some ways are:
*You can put a carpet on the steps. The fibers in a carpet usually have some friction which will give you a grip as you climb up and/or down and prevent you from falling.
*You can apply anti-slip coatings like a paint on the steps. If you add some sand to the paint to add traction and lessen the slippery nature. Alternatively, If the wood has been waxed, you may consider using a wax remover.
*You can fix a hand railing so that you can hold on to it when you go up and down the steps.
How can whales descend quickly and face no problems
Answer:
Whales face an increasing number of threats including: For hundreds of years people hunted whales for their oil to fuel lamps and candles, to lubricate machinery and to make margarine, lipsticks and other products. They also used baleen whales to make tennis racquets and corsets!
Explanation:
3 materials that are denser than water and 3 that arent denser than water
Answer:
denser than water:
1. clay
2. coins
3. rock
aren't denser than water
1. wood
2. sponge
3. apple
Identify the types of motion:-
the movement of the snail on the ground
the strings of the guitar
the whirling of stone tied with a thread
Answer:
the movement of snail on the ground is in random motion.
the strings of the guitar is in oscillatory motion.
the whirling of stone tied with a thread is in circular motion.
17. The shape of a river is determined by which of the following? (Choose all that
apply)
A Erosion
B. Deposition
C. Weathering
D. water speed
Answer:
Water speed Plays a key role In determining The shape of it
Anita Knapp needs to get hay to cows in a frozen field using an airplane flying 80.0 m/s, at a height of 300,m. If at the last minute, how far from the cow would she have to release the hay in order to hit the cow? *
Answer:
Explanation:
If we ignore wind resistance, the time needed for the hay to drop from vertical rest is
t = √(2h/g) = √(2(300)/9.81) = 7.82 s
d = vt = 80.0(7.82) = 626 m before passing over the cow.
Would it be possible to predict the speeds that a coaster will reach before it’s ever placed on the track?
Yes, it's possible to predict the speeds that a coaster will reach before it’s
ever placed on the track.
This is usually calculated with the potential energy which is
Potential energy = m g h
where m is mass, g is acceleration due to gravity and h is height.
The given formula above is used in predicting the speeds that a coaster will
reach before it’s ever placed on the track.
Read more about Speed here https://brainly.com/question/14298262
Please help me answer the following image!
what forces would a person inside an elevator feel when it is going up?