a. In a simple RC circuit, the battery is delivering the most power immediately after the switch is thrown to charge the capacitor. This is because at that moment, the capacitor is completely discharged and acts as a short circuit. This means that the full voltage of the battery is applied across the resistor, causing the largest possible current to flow through it. As the capacitor charges up, its voltage gradually increases, which decreases the voltage across the resistor and hence the current flowing through it. Therefore, the power delivered by the battery decreases as the capacitor charges up.
b. The capacitance of a capacitor is determined by the geometry of its electrodes and the type of dielectric material between them. It is independent of the charge or voltage on the capacitor. Therefore, the capacitance remains constant regardless of whether the capacitor is fully charged, half charged, or just starting to charge. This means that the amount of charge that flows onto the capacitor per unit voltage is also constant, which is why the voltage across the capacitor increases linearly as it charges up.
After a switch is thrown to charge the capacitor, the electric field is greatest in the capacitor gap when the capacitor is fully charged. This is because when the capacitor is fully charged, the voltage across its electrodes is at its maximum value. Since the electric field is proportional to the voltage gradient in the capacitor gap, it is also at its maximum value when the capacitor is fully charged. As the capacitor discharges, the voltage across its electrodes decreases, which in turn decreases the electric field in the capacitor gap.
a. In a simple RC circuit, the battery delivers the most power immediately after the switch is thrown because at that instant, the voltage across the resistor is at its maximum and the capacitor is uncharged. As the capacitor charges, the voltage across the resistor decreases, leading to a reduction in the power delivered by the battery. When the capacitor is fully charged, the voltage across the resistor becomes zero and the battery no longer delivers power.
b. The capacitance of a capacitor is constant because it depends on the geometry of the capacitor (surface area of the plates and distance between them) and the dielectric material used between the plates. These factors remain unchanged during the charging process, hence the capacitance remains constant regardless of the charge state.
The electric field in the capacitor gap is greatest when the capacitor is fully charged because the electric field is directly proportional to the charge stored on the plates. As the capacitor charges, the charge on the plates increases, leading to an increase in the electric field. Once the capacitor is fully charged, the electric field reaches its maximum value.
Learn more about RC circuit here;
https://brainly.com/question/31394676
#SPJ11
Problem 1: A rock with mass m = 1 kg is submerging with constant acceleration at = 1.8 m/s2 into the level earth. The free-fall acceleration is g = 9.81 m/s2. Please answer the following questions. Otheexpertta.com Part (a) Write an expression for the magnitude of the force of gravity on the rock, Fg, in terms of the given quantities and variables available in the palette. Expression : F = Select from the variables below to write your expression. Note that all variables may not be required. a, b, , o, 0, at, d, FN, g, h, j, k, m, P, t Part (b) Calculate the magnitude of the force of gravity on the rock, Fin Newtons. Numeric : A numeric value is expected and not an expression. Fg== Part (c) In what direction does the force of gravity act? Multiple Choice : 1) Sideways. 2) Upwards. 3) Force doesn't have direction. 4) Downwards. 5) None of these choices. 6) All of these choices. Part (d) Write an expression for the magnitude of the total force of the system in the y-direction, Ft, in terms of the forces of the system. Expression : FT= Select from the variables below to write your expression. Note that all variables may not be required. a, b, c, o, 0, at, d, F, FN, g, h, j, m, P, t Part (e) Write an expression for the magnitude of the normal force Fn, in terms of m, at, and g. Expression : FN= Select from the variables below to write your expression. Note that all variables may not be required. a, b, n, , 0, at, d, FN, g, h, j, k, m, P, t Part (1) What is the magnitude of the normal force in N? Numeric : A numeric value is expected and not an expression. Fn = Part (g) In what direction is the normal force? Multiple Choice : 1) Sideways. 2) Downwards. 3) Force does not have direction. 4) Upwards. 5) None of these choices 6) All of these choices.
Part (a) A rock with mass m = 1 kg is submerging with constant acceleration at the formula for the force magnitude of gravity acting on the rock is F = m x g (standard formula).
Part (b) : Calculate the magnitude of the force of gravity on the rock, Newtons. Numeric: A numeric value is expected and not an expression.
F == Part:
Here, m = 1 kg and g= a = 9.81 [tex]m/s^2[/tex](standard value of g)
F = m*g = 1 kg * 9.81 [tex]m/s^2[/tex]
= 9.81 N
Numeric: F = 9.81 N
Part (c): Option 4 is Correct. Because gravity pulls downward.
Part (d) The total force of the system in the y-direction, Ft, may be written down as follows: Ft = Fg - m * at while the rock is submerged with a constant acceleration.
So, here we need the Expression:
[tex]F_t = F_g + F_N\\F_t = m*g + F_N[/tex]
Part (e) The formula for the normal force Fn's magnitude is Fn = m * (g - at).
So, here we need the Expression:
[tex]F_N = m*(at + g)\\F_N = m*(at + g)[/tex]
where m is the mass of the object, at is the acceleration of the object in the y-direction, and g is the acceleration due to gravity.
Part (f) When we change the values, we obtain:
Here, m = 1 kg
at = 1.8 [tex]m/s^2[/tex]
g = 9.81 [tex]m/s^2[/tex]
[tex]F_N = m*(at + g) \\= 1 kg * (1.8 m/s^2 + 9.81 m/s^2) \\= 11.61 N[/tex]
Numeric: [tex]F_N[/tex] = 11.61 N
7.01 N is equal to [tex]F_N[/tex] = [tex]1 kg * (9.81 m/s^2 - 1.8 m/s^2)[/tex]
Part (g): Option 4 is Correct. In direction is the normal force: Upwards is the correct option.
Upwards, since the typical force moves upward.
Learn more about magnitude visit: brainly.com/question/30337362
#SPJ4
In a location where the speed of sound is 334 m/s, a 2,000 Hz sound wave impinges on two slits 30 cm apart.
(a) At what angle is the first-order maximum located?
(b) If the sound wave is replaced by 3.25 cm microwaves, what slit separation gives the same angle for the first-order maximum?
(c) If the slit separation is 1.00 μ m, what frequency of light gives the same first-order maximum angle?
So the frequency speed of sound that gives the same first-order maximum angle for a slit separation of 1.00 μm is 5.37 x [tex]10^{14[/tex] Hz.
(a) The first-order maximum for double-slit diffraction is given by the equation:
sin θ = mλ/d
where θ is the angle between the incident wave and the direction of the maximum, m is the order of the maximum (m=1 for first-order), λ is the wavelength of the wave, and d is the distance between the slits.
In this case, λ = v/f = 334 m/s / 2000 Hz = 0.167 m, and d = 30 cm = 0.3 m. Plugging in these values, we get:
sin θ = (1)(0.167 m) / (0.3 m) = 0.556
Taking the inverse sine of both sides, we find:
θ = 33.5°
So the first-order maximum is located at an angle of 33.5°.
(b) To find the slit separation that gives the same angle for microwaves with a wavelength of 3.25 cm (0.0325 m), we can rearrange the equation for the first-order maximum to solve for d:
d = mλ / sin θ
In the values for microwaves, m=1, λ=0.0325 m, and θ=33.5°, we get:
d = (1)(0.0325 m) / sin(33.5°) = 0.059 m = 5.9 cm
So the slit separation that gives the same angle for microwaves is 5.9 cm.
(c) To find the frequency of light that gives the same first-order maximum angle for a slit separation of 1.00 μm, we can rearrange the equation for the first-order maximum to solve for λ:
λ = d sin θ / m
Plugging in the values for the slit separation, m=1, and θ=33.5°, we get:
λ = (1.00 μm) sin(33.5°) / (1) = 0.559 μm
To convert this wavelength to frequency, we can use the equation:
f = v/λ
f = (3.00 x [tex]10^{14[/tex] Hz. m/s) / (5.59 x [tex]10^{14[/tex] Hz. m)
= 5.37 x [tex]10^{14[/tex] Hz. Hz
Learn more about speed of sound Visit: brainly.com/question/16012426
#SPJ4
A turbine blade rotates with angular velocity w(t) = 5.00 rad/s - 1.20 rad/s^3 t^2. What is the angular acceleration of the blade at t = 7 s? a. 10.1 rad/s^2 b. -20.2 rad/s^2 c. 23.5 rad/s^2 d. -16.8 rad/s^2 e. 13.4 rad/s^2
The angular acceleration of the blade at t = 7 s is -16.8 rad[tex]/s^2[/tex], which is option (d).
The given angular velocity of the blade is:
w(t) = 5.00 rad/s - 1.20 [tex]rad/s^3 t^2[/tex]
To find the angular acceleration of the blade, we need to differentiate the angular velocity with respect to time:
[tex]a(t) = dw(t)/dt = d/dt (5.00 rad/s - 1.20 rad/s^3 t^2)= - 2.40 rad/s^3 t[/tex]
Now, we can substitute t = 7 s into the expression for angular acceleration:
[tex]a(7) = -2.40 rad/s^3 (7)\\= -16.8 rad/s^2[/tex]
Therefore, the angular acceleration of the blade at t = 7 s is -16.8 r[tex]ad/s^2,[/tex]which is option (d).
learn more about velocity here:
https://brainly.com/question/31475519
#SPJ4
The pendulum illustrated above has a length of 2 m and a bob of mass 0.04 kg. It is held at an angle theta, as shown, where cos(theta) = 0.9. If the pendulum is released from rest, the maximum speed the bob attains is most nearly?
The maximum speed the bob of the pendulum attains is nearly 5.97 m/s.
The velocity changes continuously as the pendulum bob moves back and forth. There are times when the velocity is negative (when the pendulum bob is moving left) and other times when it is positive (when it is moving right). And, of course, there will be times when the velocity will be 0 m/s.
From the energy conservation statement
Ui + Ki = Uf + Kf
Ki = 0 as the ball is released from the state of rest.
Uf = 0 where Uf is the final potential energy
So Ui = Kf or mgh = ½ mv², where h is the height from which the ball is released.
Cancelling m on both sides we get
v = (2gh)½
To determine the height h
h = L - Lcos θ = L (1-cos θ)
h = 2 - 2× 0.09 = 1.82
So v = (2gh)½
v =( 2 × 9.8 × 1.82)¹/²
v = √35.672
v= 5.97 m/s
To learn more about speed, refer to the link:
https://brainly.com/question/30462853
#SPJ12
The maximum speed the bob of the pendulum attains is nearly 5.97 m/s.
The velocity changes continuously as the pendulum bob moves back and forth. There are times when the velocity is negative (when the pendulum bob is moving left) and other times when it is positive (when it is moving right). And, of course, there will be times when the velocity will be 0 m/s.
From the energy conservation statement
Ui + Ki = Uf + Kf
Ki = 0 as the ball is released from the state of rest.
Uf = 0 where Uf is the final potential energy
So Ui = Kf or mgh = ½ mv², where h is the height from which the ball is released.
Cancelling m on both sides we get
v = (2gh)½
To determine the height h
h = L - Lcos θ = L (1-cos θ)
h = 2 - 2× 0.09 = 1.82
So v = (2gh)½
v =( 2 × 9.8 × 1.82)¹/²
v = √35.672
v= 5.97 m/s
To learn more about speed, refer to the link:
https://brainly.com/question/30462853
#SPJ12
The graph below shows the time and position of a motorcycle as it travels through several photogates. Calculate the velocity of the motorcycle as it moves from gate C to gate D.
C. 0.5 m/s. From the graph, the change in position within 2 seconds from gate C to gate D is 1 m. Then, the velocity of the motorcycle is 0.5 m/s. Hence, option C is correct.
What is position - time graph ?Position - time graph of an item describes the change in position with regard to time. The time is given in the x-axis, while the position is given in the y-axis. The position-time graph can be used to determine the object's velocity. The ratio of a moving object's distance travelled to its travel time is its velocity. The velocity unit is m/s. Being a vector quantity with magnitude and direction, velocity has both.
From the graph, the time taken by the motor cycle is 2 seconds. The distance travelled from C to D is 1 m (7 m to 8 m).
velocity = distance/ time
v = 1 m/ 2 s
= 0.5 m/s.
To know more about the position -time graph visit:
https://brainly.com/question/29084676
#SPJ1
calculate the resistance of a 40w automobile headlight designed for 12v
The resistance of the 40W automobile headlight designed for 12V is approximately 3.6 ohms.
Explanation:
To calculate the resistance of a 40W automobile headlight designed for 12V, we will use Ohm's Law and the formula for power.
Step 1: Recall the formula for power: P = IV, where P is power, I is current, and V is voltage.
Step 2: Rearrange the formula to solve for current (I): I = P / V
Step 3: Plug in the given values for power (40W) and voltage (12V): I = 40W / 12V
Step 4: Calculate the current: I = 3.33A
Step 5: Recall Ohm's Law: V = IR, where V is voltage, I is current, and R is resistance.
Step 6: Rearrange the formula to solve for resistance (R): R = V / I
Step 7: Plug in the given values for voltage (12V) and the calculated current (3.33A): R = 12V / 3.33A
Step 8: Calculate the resistance: R = 3.6Ω
The resistance of the 40W automobile headlight designed for 12V is approximately 3.6 ohms.
To know more about resistance visit:
https://brainly.com/question/30799966
#SPJ11
Home-made x-ray source: You have a 4000 volt DC, 200 watt power supply. Which elements are suitable for use as your anode (target) material for generating Kb x-rays?
For generating Kb x-rays using a home-made x-ray source with a 4000 volt DC, 200 watt power supply, suitable elements for use as your anode (target) material would be those with a high atomic number such as tungsten (W), molybdenum (Mo), or copper (Cu).
These elements are known to produce intense Kb x-rays at the given voltage and wattage, making them ideal for use in an improvised x-ray source.
It is important to note, however, that operating a home-made x-ray source can be extremely hazardous and should only be attempted by trained professionals with appropriate safety equipment and precautions in place.
To know more about elements refer here:
https://brainly.com/question/13025901
#SPJ11
Using what you know about the compressibility of different states of matter explain why
a) air is used to inflate tyres
b) steel is used to make railway lines
Answer:
Explanation:
a) Air is highly compressible. As it has pressure it can also handle atm (Atmosphere) pressure. It makes the drving smooth and gives the required friction for driving. Also it is very easily available.
b) Steel is free from rust and it has high tensile strength. It has the resistence to internal and external cracks.
A rod is being used as a lever. The fulcrum is 1.2m from the load and 2.4m form the applied force. The applied force is being applied at the end of the rod. If the load has a mass of 20.0kg, what force must be applied to lift the load?
Using the lever principle, a force of 98N is needed to lift the 20.0kg load. The load distance is 1.2m and the effort distance is 2.4m.
To solve this problem, we can use the formula for the lever principle:
(load distance) x (load force) = (effort distance) x (effort force)
In this case, the load distance is 1.2m, the load force is the weight of the load [tex](20.0kg x 9.8m/s^2 = 196N[/tex]), the effort distance is 2.4m, and the effort force is what we need to find. Plugging in these values, we get:
(1.2m) x (196N) = (2.4m) x (effort force)
Simplifying and solving for the effort force, we get:
effort force = (1.2m x 196N) / 2.4m = 98N
Therefore, a force of 98N must be applied to lift the load.
learn more about force here:
https://brainly.com/question/13191643
#SPJ11
A wire carrying 15 A makes a 23 ∘ angle with a uniform magnetic field. The magnetic force per unit length of wire is 0.34 N/m .
Part A
What is the magnetic field strength? In (mT)
Express your answer using two significant figures.
Part B
What is the maximum force per unit length that could be achieved by reorienting the wire in this field? in (N/m)
Express your answer using two significant figures.
the maximum force per unit length that could be achieved by reorienting the wire in this field is approximately 0.15 N/m.
Part A:
Using the formula for magnetic force per unit length, we can solve for the magnetic field strength:
F/L = BILsinθ
0.34 N/m = B(15 A)Lsin23°
B = 0.34 N/m / (15 A)(Lsin23°)
Since we do not have the length of the wire, we cannot solve for the exact magnetic field strength. However, we can rearrange the formula to show that magnetic field strength is proportional to the magnetic force per unit length, the current, and the sine of the angle between the wire and the magnetic field:
B ∝ F/LIsinθ
Therefore, if we know the magnetic force per unit length and the angle, we can compare the strength of two different magnetic fields. For example, if we have another wire carrying the same current and making the same angle with a different magnetic field, we can compare the magnetic force per unit length and use the formula above to determine which magnetic field is stronger.
Part B:
The maximum force per unit length that could be achieved by reorienting the wire in this field would occur when the wire is perpendicular to the magnetic field. In this case, the angle θ would be 90° and the sine of 90° is 1. Therefore, we can use the same formula as above and plug in the maximum value for sinθ:
F/L = BILsinθ
F/L = BIL(1)
F/L = BIL
F/L = (0.001 T)(15 A)
F/L = 0.015 N/m
Therefore, the maximum force per unit length that could be achieved by reorienting the wire in this field is 0.015 N/m (rounded to two significant figures).
Part A
To find the magnetic field strength, we can use the formula for magnetic force per unit length on a current-carrying wire in a uniform magnetic field:
F/L = B * I * sin(θ)
where F/L is the force per unit length (0.34 N/m), B is the magnetic field strength, I is the current (15 A), and θ is the angle between the wire and the magnetic field (23°).
0.34 N/m = B * 15 A * sin(23°)
B = (0.34 N/m) / (15 A * sin(23°))
B ≈ 0.0102 T
To express the answer in millitesla (mT), we multiply by 1000:
B ≈ 10.2 mT
Part B
The maximum force per unit length occurs when the angle between the wire and the magnetic field is 90° (sin(90°) = 1):
Fmax/L = B * I * sin(90°)
Fmax/L = 10.2 mT * 15 A * 1
Fmax/L ≈ 0.153 N/m
So, the maximum force per unit length that could be achieved by reorienting the wire in this field is approximately 0.15 N/m.
To know more about magnetic field strength click here:
brainly.com/question/11462606
#SPJ11
37.•• an object has a weight of 8.0 n in air. however, it apparently weighs only 4.0 n when it is completely submerged in water. what is the density of the object?
The density of an object has a weight of 8.0 N in air and an apparent weight of 4.0 N when submerged in water is 2000 kg/m³.
To determine the density of an object with a weight of 8.0 N in air and an apparent weight of 4.0 N when submerged in water, you'll need to use Archimedes' principle and the formula for density.
First, calculate the buoyant force (which is equal to the loss of weight in water):
Buoyant force = Weight in air - Apparent weight in water
= 8.0 N - 4.0 N
= 4.0 N
Next, calculate the volume of displaced water using the buoyant force and the density of water (1000 kg/m³):
Volume = Buoyant force / (density of water × gravity)
= 4.0 N / (1000 kg/m³ × 9.81 m/s²)
≈ 0.000408 m³
Now, find the mass of the object using its weight and gravity:
Mass = Weight / gravity
= 8.0 N / 9.81 m/s²
≈ 0.815 kg
Finally, determine the density of the object using the mass and the volume:
Density = Mass / Volume
≈ 0.815 kg / 0.000408 m³
≈ 2000 kg/m³
So, the density of the object is approximately 2000 kg/m³.
Learn more about density: https://brainly.com/question/29775886
#SPJ11
Write a differential equation that models the given situation. The stated rate of change is with respect to time t. (Use k for the proportionality constant.) For a car with maximum velocity M, the rate of change of the velocity v of the car is proportional to the difference between M and v. dv/dt=?
dv/dt = k is the differential equation that describes the situation as it is (M - v)
How can you tell if a function is a certain differential equation's solution?The same procedure as before is used to assess whether a function is a solution to a certain differential equation: we evaluate the left and right sides of the d.e. and compare the results to check if they are equal.
What is a differential equation solution?An expression for the dependent variable in terms of one or more independent variables that satisfy the relationship is the differential equation's solution. The generic solution often contains arbitrary constants or arbitrary functions and encompasses all potential solutions.
To know more about differential equation visit:-
https://brainly.com/question/30896158
#SPJ1
lens 2 - the diverging lens: what is the object distance do2 with a proper sign?
This formula gives us the object distance (do2) for a given image distance (di) and focal length (f2) of the diverging lens.
As a diverging lens always produces virtual images, the object distance (do2) for a diverging lens is always negative.
To calculate the object distance, we need to use the lens formula:
[tex]1/f = 1/do_2 + 1/d_i[/tex]
Since the image formed by a diverging lens is always virtual, di will also be negative. Let's assume that the image distance is -di.
Then, the equation becomes:
[tex]1/f = 1/do_2 - 1/d_i[/tex]
We know that the focal length of a diverging lens is always negative, so let's assume that f = -f2.
Substituting the given values, we get:
[tex]do_2 = f_2 * d_i / (d_i - f_2)[/tex]
Since the object distance is negative for a diverging lens, we can put a negative sign before the formula:
[tex]do_2 = -f_2 * d_i / (d_i - f_2)[/tex]
Learn more about focal length visit: brainly.com/question/28039799
#SPJ4
Correct Question:
For the below lens 2 - the diverging lens: what is the object distance do2 with a proper sign?
what is the standard enthalpy of a reaction for which the equilibrium constant is (a) doubled and (b) halved when the temperature is increased from 298 k to 308 k?
The standard enthalpy of a reaction is affected by changes in temperature and equilibrium constant, with higher temperatures generally leading to more negative values of enthalpy for favorable reactions.
What's standard enthalpyThe standard enthalpy of a reaction is the change in enthalpy that occurs during a chemical reaction under standard conditions, which include a temperature of 298 K and a pressure of 1 bar.
When the temperature is increased from 298 K to 308 K, the equilibrium constant of a reaction will change, which will in turn affect the standard enthalpy of the reaction.
If the equilibrium constant is doubled when the temperature is increased, this means that the reaction is becoming more favorable in the forward direction. In this case, the standard enthalpy of the reaction will become more negative, indicating that more heat is released during the reaction.
On the other hand, if the equilibrium constant is halved when the temperature is increased, this means that the reaction is becoming less favorable in the forward direction. In this case, the standard enthalpy of the reaction will become less negative, indicating that less heat is released during the reaction.
Learn more about enthalpy at
https://brainly.com/question/13996238
#SPJ11
A 950-kg sports car accelerates from rest to 95 km/h in 6.0 s. What is the average power delivered by the engine?
The average power delivered by the engine is 20,708 watts.
To calculate the average power, follow these steps:
1. Convert 95 km/h to meters per second (m/s): 95 km/h * (1000 m/km) / (3600 s/h) = 26.39 m/s.
2. Calculate the car's final kinetic energy (KE) using the formula KE = 0.5 * mass * velocity²: 0.5 * 950 kg * (26.39 m/s)^2 = 330,322.95 J.
3. Since the car starts from rest, the initial KE is 0 J.
4. Calculate the change in kinetic energy: Final KE - Initial KE = 330,322.95 J - 0 J = 330,322.95 J.
5. Calculate the average power using the formula: Power = Change in KE / time: 330,322.95 J / 6.0 s = 20,708.33 W, which can be rounded to 20,708 watts.
To know more about average power click on below link:
https://brainly.com/question/30888338#
#SPJ11
a 3.10 kg rock whose density is 4600 kg/m3 is suspended by a string such that half of the rock's volume is under water.. What is the tension in the string?
the equation using V_rock = 3.10 / 4600 (since density = mass / volume), we get:Tension = 30.38 N
How to solve the question?
To solve this problem, we can use Archimedes' principle, which states that the buoyant force on an object submerged in a fluid is equal to the weight of the fluid displaced by the object. In this case, the buoyant force acting on the rock is equal to the weight of the water displaced by the part of the rock submerged in water.
First, we need to find the volume of the rock. We know that half of the rock's volume is under water, so the volume of the rock is:
V_rock = (2 * V_underwater) = (2 * (0.5 * V_rock)) = V_rock
where V_underwater is the volume of the rock submerged in water.
Rearranging the equation, we can find the volume of the rock:
V_rock = V_underwater / 0.5
Next, we can find the weight of the water displaced by the rock, which is equal to the buoyant force acting on the rock:
F_buoyant = weight of water displaced = density of water * volume of water displaced * gravity
where density of water = 1000 kg/m³, volume of water displaced = 0.5 * V_rock, and gravity = 9.8 m/s²
Substituting the values, we get:
F_buoyant = 1000 * (0.5 * V_rock) * 9.8
Now, we can find the weight of the rock:
weight of rock = mass of rock * gravity
where mass of rock = 3.10 kg and gravity = 9.8 m/s².
Substituting the values, we get:
weight of rock = 3.10 * 9.8
Finally, the tension in the string is equal to the weight of the rock minus the buoyant force acting on the rock:
Tension = weight of rock - F_buoyant
Substituting the values, we get:
Tension = (3.10 * 9.8) - (1000 * (0.5 * V_rock) * 9.8)
Simplifying the equation using V_rock = 3.10 / 4600 (since density = mass / volume), we get:
Tension = 30.38 N
Therefore, the tension in the string is 30.38 N.
To know more about tension visit :-
https://brainly.com/question/24994188
#SPJ1
what work is done by the electric force when the charge moves a distance of 0.720 mm upward?
Work DONE BY Electric force
W = Fd = Eqd
To calculate the work done by the electric force when a charge moves a distance of 0.720 mm upward, we need to use the formula W = Fd, where W is the work done, F is the electric force, and d is the distance moved.
Assuming the charge is moving in a uniform electric field, we can use the formula F = Eq, where E is the electric field strength and q is the charge of the particle.
So, we have W = Fd = Eqd and d = 0.720 mm. Substituting these values into the work formula, we get:
W = Fd = Eqd
To solve for W, we need to know the values of E and q. If these are not given in the problem, we cannot solve for W.
However, we can say that the work done by the electric force depends on the magnitude of the charge and the strength of the electric field.
If the charge is positive and moves in the direction of the electric field, the electric force will do positive work (i.e. the force and displacement are in the same direction).
If the charge is negative and moves opposite to the electric field, the electric force will do negative work (i.e. the force and displacement are in opposite directions).
For more information on work by electric forcehttps://brainly.com/question/25923373
#SPJ11
A Normalize this wave function. What is the (positive) value of C once this wave function is normalized? You will need the formula se eres? = V -az? Express your answer in terms of w, m, n, and . View Available Hint(s) 190 AED ? CE Submi
Normalizing a wave function and finding the value of the constant C. The wave function you provided is not clear, but I can still guide you through the process.
To normalize a wave function, you need to ensure that the integral of the wave function's magnitude squared over all space is equal to 1. The formula for normalization is:
∫ |Ψ(x)|^2 dx = 1
Here, Ψ(x) represents the wave function, and |Ψ(x)|^2 represents the square of the wave function's magnitude. To find the positive value of C, you would need to:
1. Multiply the wave function by its complex conjugate: C*Ψ(x)*CΨ*(x), where Ψ*(x) is the complex conjugate of Ψ(x).
2. Integrate the result over all space.
3. Set the integral equal to 1 and solve for C.
once you have the wave function, you can follow these steps to find the value of C in terms of the given variables.
To learn more about magnitude click here
brainly.com/question/30395926
#SPJ11
if a current of 50 ma exists for 1.4 min, how many coulombs of charge have passed through the wire?
To find the total charge that has passed through the wire, we can use the formula Q = I x t, where Q is the charge in coulombs, I is the current in amperes, and t is the time in seconds.
First, we need to convert the current from milliamperes to amperes by dividing by 1000:
50 mA = 0.05 A
Next, we need to convert the time from minutes to seconds by multiplying by 60:
1.4 min = 84 s
Now we can plug in the values and solve for Q:
Q = 0.05 A x 84 s
Q = 4.2 C
Therefore, 4.2 coulombs of charge have passed through the wire.
Learn more about current here:
https://brainly.com/question/31297138
#SPJ11
suppose that you wish to construct a telescope that can resolve features 9.5 km across on the moon, 384,000 km away. you have a 3.8 −m -focal-length objective lens whose diameter is 13.0 cm .
To construct a telescope that can resolve features 9.5 km across on the moon, 384,000 km away. you have a 3.8 m focal-length objective lens whose diameter is 13.0 cm , we would need a magnification of approximately 81.5x.
To calculate the required angular resolution of the telescope, we can use the formula:
θ = 1.22 λ/D
Where θ is the angular resolution, λ is the wavelength of light (we'll assume a value of 550 nm for green light), and D is the diameter of the objective lens.
θ = 1.22 (550 nm) / (13 cm) = 0.000303 radians
Next, we can calculate the angular size of the features on the moon:
θ = size / distance
where size is the size of the feature we want to resolve (9.5 km) and distance is the distance to the moon (384,000 km).
θ = (9.5 km) / (384,000 km)
= 0.0000247 radians
Finally, we can calculate the magnification required to achieve the desired resolution:
Magnification = angular size of the feature / angular resolution of the telescope
Magnification = 0.0000247 radians / 0.000303 radians = 81.5
Therefore, we would need a magnification of approximately 81.5x to resolve features 9.5 km across on the moon using a 3.8 m focal length objective lens with a diameter of 13 cm.
Learn more about focal length here:
https://brainly.com/question/28039799
#SPJ11
To construct a telescope that can resolve features 9.5 km across on the moon, 384,000 km away. you have a 3.8 m focal-length objective lens whose diameter is 13.0 cm , we would need a magnification of approximately 81.5x.
To calculate the required angular resolution of the telescope, we can use the formula:
θ = 1.22 λ/D
Where θ is the angular resolution, λ is the wavelength of light (we'll assume a value of 550 nm for green light), and D is the diameter of the objective lens.
θ = 1.22 (550 nm) / (13 cm) = 0.000303 radians
Next, we can calculate the angular size of the features on the moon:
θ = size / distance
where size is the size of the feature we want to resolve (9.5 km) and distance is the distance to the moon (384,000 km).
θ = (9.5 km) / (384,000 km)
= 0.0000247 radians
Finally, we can calculate the magnification required to achieve the desired resolution:
Magnification = angular size of the feature / angular resolution of the telescope
Magnification = 0.0000247 radians / 0.000303 radians = 81.5
Therefore, we would need a magnification of approximately 81.5x to resolve features 9.5 km across on the moon using a 3.8 m focal length objective lens with a diameter of 13 cm.
Learn more about focal length here:
https://brainly.com/question/28039799
#SPJ11
an airplane has to land at a destination 300 km northeast with a wind blowing at 40 km/h due south. if the airspeed of the plane is 180 km/h, what is the required heading of the plane?
To calculate the required heading of the plane, we need to use vector addition. The velocity of the plane relative to the ground can be found by adding the velocity of the plane relative to the air (airspeed) to the velocity of the wind relative to the ground.
First, we need to find the velocity of the wind relative to the plane. We can do this by subtracting the velocity of the wind due south (40 km/h) from the velocity of the plane due northeast (180 km/h).
Using the Pythagorean theorem, we can find the magnitude of the velocity of the plane relative to the ground:
(180 km/h)^2 + (40 km/h)^2 = 33800
√33800 = 183.7 km/h
Now we can use trigonometry to find the angle between the velocity of the plane relative to the ground and the direction of the destination (northeast).
tan θ = opposite/adjacent = 300 km/183.7 km/h
θ = tan^-1 (300/183.7) = 59.8°
Therefore, the required heading of the plane is 59.8° northeast.
To find the required heading of the plane, we need to consider the wind and the airspeed of the plane. Since the wind is blowing due south at 40 km/h and the plane's airspeed is 180 km/h, we can use vector addition to find the ground speed vector of the plane.
Let's represent the plane's airspeed vector as A and the wind's vector as W. The ground speed vector, G, can be represented as G = A + W. The plane needs to travel 300 km northeast, so we'll need to adjust the plane's airspeed vector accordingly.
Given the wind vector W = [0, -40] (0 in the east-west direction and -40 in the north-south direction) and the desired ground speed vector G = [300/sqrt(2), 300/sqrt(2)] (since it's traveling northeast).
Now, we'll find the airspeed vector A:
A = G - W
A = [300/sqrt(2), 300/sqrt(2) + 40]
Now, to find the required heading of the plane, we need to calculate the angle with respect to the east direction:
angle = arctan(A_y/A_x)
angle = arctan((300/sqrt(2) + 40)/(300/sqrt(2)))
Use a calculator to find the angle value. This will give you the required heading of the plane to reach its destination 300 km northeast considering the wind and airspeed.
Visit here to learn more about magnitude brainly.com/question/14452091
#SPJ11
You are spinning two identical balls attached to strings in uniform circular motion, Ball 2 has a string that is twice as long as the string with ball 1, and the rotational speed (v) of ball 2 is three times the rotational speed of ball 1. What is the ratio of the centripetal force of ball 2 to that of ball 1?
The ratio of the centripetal force of ball 2 to that of ball 1 is 9:2.
To find the ratio of the centripetal force of ball 2 to that of ball 1, let's first look at the formula for centripetal force:
[tex]F_c = m * v^2 / r[/tex]
where [tex]F_c[/tex] is the centripetal force, m is the mass of the ball, v is the rotational speed, and r is the radius (or length of the string).
Given that ball 2 has a string that is twice as long as ball 1, we can represent the radii as:
[tex]r_1[/tex] = r (for ball 1)
[tex]r_2[/tex] = 2r (for ball 2)
Also, the rotational speed of ball 2 is three times the rotational speed of ball 1, so we have:
[tex]v_1[/tex] = v (for ball 1)
[tex]v_2[/tex] = 3v (for ball 2)
Now, we can substitute these values into the centripetal force formula for each ball:
[tex]F_{c1} = m * v^2 / r\\F_{c2} = m * (3v)^2 / (2r)[/tex]
Now, we need to find the ratio of [tex]F_{c2}[/tex] to [tex]F_{c1}[/tex]:
[tex]F_{c2} / F_{c1} = (m * (3v)^2 / (2r)) / (m * v^2 / r)[/tex]
The mass (m) and the speed squared (v²) terms will cancel out:
[tex]F_{c2} / F_{c1} = ((3^2) / 2)\\F_{c2} / F_{c1} = (9 / 2)[/tex]
Learn more about centripetal force:
https://brainly.com/question/20905151
#SPJ11
The speed-time graph of a car is shown in the figure, which of the following statement is true: (figure shown in attachment)
• Car has an acceleration of 1.5 ms-2
• Car has constant speed of 7.5 ms-1
• Distance travelled by the car is 75 m
• Average speed of the car is 15 ms-1
In the speed-time graph of a car in the figure, the correct statement is, the distance traveled by car is 75 m. Thus, option C is correct.
Speed is the distance traveled by an object per unit of time. In the graph, speed is taken in the Y axis, and time in the X axis. In the speed-time graph, the acceleration of an object and the distance traveled by an object can be determined. In the speed-time graph, the acceleration is obtained by taking the slope. From the figure, the speed of the car decreases, and it is called deceleration. If the car has a constant speed, the graph has a line parallel to the X-axis.
The distance traveled by car is obtained by determining the area of the figure. The area of the figure is a triangle.
Distance = Area of the triangle = 1/2 (base×height)
= (15×10) /2
= 75m
The distance traveled by car is 75m. The ideal solution is C.
To learn more about the speed-time graph:
https://brainly.com/question/17261628
#SPJ1
A car is traveling at a speed of 30m/s when it leaves a ramp set up at an angle of 37 degrees from the ground. How much time does it take for the car to reach the maximum height of its jump?
The time in which the car reaches it maximum Haight is ≈1.8 seconds.
We know that when the car leaves the ramp , it will move in upward direction and forward direction .
velocity of moving forward= v cos(a).......(initial velocity of moving front)
velocity of moving upward = v sin(a).......(initial velocity of moving up)
v is the initial velocity of car(30m/s), a is the angle of ramp(37°).
velocity of moving up for car at Max. hight = 0m/s
We know that,
final velocity=initial velocity - gt (g is acceleration due to gravity, t is time)
when something moves upward .
so,
0=v sin(a)-9.8t
t≈1.8 seconds
To learn more about Projectile Motion go to :
https://brainly.com/question/4247569?referrer=searchResults
Case 1 Vo V COP POLICE The radar in a cop car uses a frequency of 7.500x10°Hz. Assume the EM waves from the radar propagate in ALL directions. Case 1: A car and the cop car move in opposite direction away from each other. speed of car Vo = 26.0 m/s. Speed of Cop car Vcop = 53.0 m/s What is the RELATIVE SPEED between the car and the cop car?
The relative speed between the car and the cop car is the difference between their velocities, or in this case is 27.0 m/s.
What is relative speed?Relative speed is the rate at which two objects move in relation to each other. It measures the distance between two objects, such as two cars, over a period of time and is often expressed as a ratio of two speeds. Relative speed can also be used to quantify the motion of an object in a certain direction, such as a vehicle moving along a highway. Relative speed is an important concept in physics and engineering, as it helps to define the motion of objects in a given environment.
The relative speed between the car and the cop car is the difference between the two speeds. Since the car and the cop car are moving in opposite directions, this means that their velocities are subtracting from each other. Therefore, the relative speed between the car and the cop car is the difference between their velocities, or in this case:
Relative speed = Vcop - Vo = 53.0 m/s - 26.0 m/s
= 27.0 m/s.
To learn more about relative speed
https://brainly.com/question/31320632
#SPJ1
Some makes of older cars have 6.00-V electrical systems. (a) What is the hot resistance of a 30.0-W headlight in such a car? (b) What current flows through it?
According to the question the R is the resistance is 0.2 Ω and I is the current is 30.0 A.
What is resistance?Resistance is the opposition to the flow of current through a material. Resistance is measured in ohms and is caused by the collisions between electrons and ions in the material. Resistance is a key component of electrical circuits, and is used to regulate the flow of electrical current.
a) The hot resistance of a 30.0-W headlight in a 6.00-V electrical system can be calculated using the equation:
R = V/I
where R is the resistance, V is the voltage and I is the current.
Therefore, R = 6.00/30.0 = 0.2 Ω
b) The current flowing through the 30.0-W headlight in a 6.00-V electrical system can be calculated using the equation:
I = V/R
where I is the current, V is the voltage, and R is the resistance.
Therefore, I = 6.00/0.2 = 30.0 A.
To learn more about resistance
https://brainly.com/question/17563681
#SPJ1
which one of the following compounds would exhibit seven signals in its 13c nmr spectrum? group of answer choices v iii iv i ii
To determine which compound would exhibit seven signals in its 13C NMR spectrum, we need to evaluate the number of unique carbon environments in each compound. Unique carbon environments are carbons that are not equivalent due to their connectivity or other factors.
Unfortunately, the specific compounds (i.e., v, iii, iv, i, ii) have not been provided. To help you further, please provide the structures or formulas of the compounds labeled as v, iii, iv, i, and ii.
The compound that would exhibit seven signals in its 13C NMR spectrum is compound IV.
Learn more about environments here:
https://brainly.com/question/29885760
#SPJ11
3. what is the spring constant? k = 0.49 incorrect: your answer is incorrect. n/cm 4. what is the force of the spring
The force of the spring is 1.6 meters. To determine the force of the spring, you would need to know the spring constant (k) and the displacement (x) of the spring from its equilibrium position.
The spring constant (k) represents the stiffness of a spring and is measured in units of force per unit length, such as N/m or N/cm. It describes the relationship between the force exerted on the spring (F) and its displacement (x) according to Hooke's Law: F = kx.
F = force exerted on the spring (N) where Kx
K = spring constant (3 kg/s2), and x = spring extension (m).
But force applied by an object is equal to mass times acceleration (9.8 m/s2).
F = 0.49kg × 9.8m/s²
F = 4.802N
Given that F = 4.802N
F = Kx 4.802 = 3 x 4.802/3 x = 1.6006 x = 1.6 m
The spring is stretched by 1.6 meters, or its extent.
Once you have both of these values, you can use the formula F = kx to calculate the force of the spring.
Learn more about Hooke's Law here
https://brainly.com/question/29126957
#SPJ11
The decay constant of a radioactive nuclide is 4.6 × 10-3 s-1. What is the half-life of the nuclide?3.6 min2.5 min2.0 min1.4 min3.1 min
The decay constant of a radioactive nuclide is 4.6 × 10-3 s-1. the half-life of the nuclide is approximately 2.5 minutes.
To determine the half-life of the radioactive nuclide with a decay constant of 4.6 × 10⁻³ s⁻¹, we can use the following formula:
Half-life (T½) = ln(2) / decay constant
Where ln(2) is the natural logarithm of 2, which is approximately 0.693.
Now, plug in the given decay constant:
T½ = 0.693 / (4.6 × 10⁻³ s⁻¹)
T½ ≈ 150.65 seconds
To convert seconds to minutes, divide by 60:
T½ ≈ 150.65 / 60
T½ ≈ 2.51 minutes
So, the half-life of the nuclide is approximately 2.5 minutes.
Learn more about the half-life of the radioactive nuclide at brainly.com/question/14392508
#SPJ11
Please help!!! I will mark brainiest!!!!
For a beam of length 20.0 m and mass 40.0 kg resting on two supports placed at 5.0 m from each end with a person of mass 50.0kg on the beam between the supports, the value of N₁ + N₂ is 882.9 N.
How to calculate reaction forces?The weight of the beam and the person is equal to the sum of the reaction forces at the supports:
W + P = N₁ + N₂
where W = weight of the beam and
P = weight of the person.
W = mg = 40.0 kg × 9.81 m/s² = 392.4 N
P = mg = 50.0 kg × 9.81 m/s² = 490.5 N
So, N₁ + N₂ = W + P = 882.9 N.
Find out more on reaction force here: https://brainly.com/question/29447428
#SPJ1