137 . a nearsighted man cannot see objects clearly beyond 20 cm from his eyes. how close must he stand to a mirror in order to see what he is doing when he shaves?

To determine the pressure gradient (d p/ds) required to accelerate water in a horizontal pipe at a rate of 30 m/s², we can use the Euler's equation for fluid flow. The terms to be included in the answer are pressure gradient (dp/ds), water, horizontal pipe, and acceleration rate (30 m/s²).

Step 1: State the Euler's equation for fluid flow in the horizontal direction:
dp/ds = -ρ * a

Where:
dp/ds = pressure gradient along the streamline
ρ = density of the fluid (water, in this case)
a = acceleration of the fluid (30 m/s²)

Step 2: Determine the density (ρ) of water:
For water at room temperature, the density (ρ) is approximately 1000 kg/m³.

Step 3: Calculate the pressure gradient (dp/ds) using Euler's equation:
dp/ds = -ρ * a
dp/ds = -1000 kg/m³ * 30 m/s²
dp/ds = -30000 kg/(m²s)

The required pressure gradient (d p/ds) along the streamline to accelerate water in a horizontal pipe at a rate of 30 m/s² is -30,000 kg/(m²s).

To know more about Euler's equation:

https://brainly.com/question/12977984

#SPJ11

If the pendulum illustrated above has a length of 2m and a bob of mass of 0.04 kg. The frequency of oscillation is most nearly is: E.) (√5)/(2π) hz.

The frequency of a simple pendulum is given by:

f = 1/(2π) √(g/L)

where g is the acceleration due to gravity, and L is the length of the pendulum.

In this case, L = 2m and the mass of the bob is 0.04kg. We are given cos(theta) = 0.9, so sin(theta) = √(1 - cos^2(theta)) = 0.4359.

The force of gravity on the bob is given by F = mg, where m is the mass of the bob and g is the acceleration due to gravity. The component of this force acting along the direction of motion is F sin(theta) = mg sin(theta) = 0.04 x 9.8 x 0.4359 = 0.170 N.

Using this force and the length of the pendulum, we can find the acceleration of the bob along the direction of motion:

a = F sin(theta)/m = 0.170/0.04 = 4.25 m/s^2

Substituting this acceleration and the length of the pendulum into the formula for frequency, we get:

f = 1/(2π) √(g/L) = 1/(2π) √(4.25/2) = (√5)/(2π) Hz

Therefore, the answer is E.

Learn more about frequency of oscillation  here:https://brainly.com/question/30694091

#SPJ1

The specific heat of the sulfuric acid is 14 J/g⁰C.

The heat lost be the water is equal to heat gain by the acid.

Q(acid) = W(water)

mcΔθ_(A) = mcΔθ _(w)

where;

The specific heat of the sulfuric acid is calculated as follows

8 g x c x (30 - 24) = 40g x 4.2J/gC x (24 - 20)

48c = 67.2

c = 67.2/48

c = 14 J/g⁰C

Learn more about specific heat capacity here: https://brainly.com/question/16559442

#SPJ1

Magnetic field strength of wire at 1.0 cm = 1.09 x 10^-4 T

To determine the magnetic field strength 1.0 cm away from the wire, we first need to calculate the current flowing through the wire using Ohm's law.

1. Find the resistance (R) of the wire using its length (L), diameter (d), and resistivity (ρ) of nichrome (1.10 x 10^-6 Ωm).
Area (A) = π(d/2)^2 = π(0.001/2)^2 = 7.85 x 10^-7 m^2
R = ρ(L/A) = (1.10 x 10^-6 Ωm)(1.0 m / 7.85 x 10^-7 m^2) = 1.40 Ω

2. Calculate the current (I) using Ohm's law: V = IR
I = V/R = 12V / 1.40 Ω = 8.57 A

3. Determine the magnetic field strength (B) at a distance (r) of 1.0 cm using Ampere's Law (B = μ₀I / 2πr), where μ₀ is the permeability of free space (4π x 10^-7 Tm/A).
B = (4π x 10^-7 Tm/A)(8.57 A) / (2π(0.01 m)) = 1.09 x 10^-4 T

The magnetic field strength 1.0 cm away from the wire is 1.09 x 10^-4 T.

Visit https://brainly.com/question/11514007 to know more about Magnetic Field

#SPJ11

About 6.15% of the incident intensity is transmitted through the polarizers. When unpolarized light passes through a polarizer, only the component of the electric field vector that is parallel to the transmission axis is transmitted, while the component perpendicular to it is absorbed. If the light passes through another polarizer whose transmission axis is at an angle to the first polarizer, the intensity of the transmitted light depends on the relative orientation of the axes.

In this case, the transmission axes of the two polarizers are at an angle of 35.0 ∘ with respect to each other. We can use Malus' law to calculate the fraction of the incident intensity that is transmitted through the polarizers. Malus' law states that the intensity of light transmitted through a polarizer is proportional to the square of the cosine of the angle between the transmission axis and the polarization direction of the incident light.

Let I0 be the incident intensity of the unpolarized light, and I1 and I2 be the intensities of the light transmitted through the first and second polarizers, respectively. The first polarizer will transmit only half of the incident intensity, since the light is unpolarized and has equal components in all directions. Therefore, I1 = (1/2)I0.

The second polarizer will transmit a fraction of the light that depends on the angle between its transmission axis and the polarization direction of the light transmitted through the first polarizer. This angle is the sum of the angles between the first polarizer and the incident light and between the second polarizer and the transmitted light. Since the transmission axes are at an angle of 35.0 ∘ with respect to each other, this angle is 70.0 ∘. Therefore, the fraction of the intensity transmitted through the second polarizer is:

I2/I1 = cos²(70.0 ∘) = 0.123

Multiplying this by the intensity transmitted through the first polarizer gives:

I2 = (0.123)(1/2)I0 = 0.0615I0

Therefore, the fraction of the incident intensity that is transmitted through both polarizers is:

I/I0 = I2/I0 = 0.0615

So, about 6.15% of the incident intensity is transmitted through the polarizers.

To learn more about unpolarized light  please visit:

https://brainly.com/question/1601505

#SPJ11

The strength of the magnetic field is approximately 2.8 mT.

The equation is:

Φ = B × A × cos(θ)

You are given the magnetic flux (Φ = 4.7 × [tex]10^-^5[/tex] [tex]Tm^2[/tex], the angle (θ = 37°), and the dimensions of the rectangular area (6.2 cm x 7.5 cm). First, we need to calculate the area (A):

A = length × width = 6.2 cm × 7.5 cm = 46.5 [tex]cm^2[/tex]

= 0.00465 [tex]m^2[/tex]

Next, rearrange the magnetic flux equation to solve for the magnetic field (B):

B = Φ / (A × cos(θ))

Now, plug in the given values and calculate the magnetic field:

B = (4.7 ×[tex]10^-^5[/tex] [tex]Tm^2[/tex]) / (0.00465[tex]m^2[/tex]× cos(37°)) ≈ 0.00283 T

Finally, convert the magnetic field strength to milli tesla (mT) and express it using two significant figures:

B = 0.00283 T × 1000 mT/T ≈ 2.8 mT

So, the strength of the magnetic field is approximately 2.8 mT.

To know more about Magnetic field refer here :

https://brainly.com/question/26257705

#SPJ11

The statement "The centripetal force always points in the same direction as the centripetal acceleration" is true. The centripetal force and centripetal acceleration both always point toward the center of the circular path, making their directions the same. This is because centripetal force is responsible for keeping an object moving in a circular path and is directly related to centripetal acceleration.

The centripetal force is the force that acts on an object moving in a circular path, which pulls the object toward the center of the circle. Centripetal acceleration is the acceleration of an object moving in a circular path, which is always directed toward the center of the circle. According to Newton's second law of motion, the net force acting on an object is equal to the product of its mass and its acceleration.

Learn more about the centripetal force: https://brainly.com/question/898360

#SPJ11

The time rate of change of the magnetic flux is D) None of These because:

We can use Faraday's Law of Electromagnetic Induction to relate the induced voltage to the time rate of change of magnetic flux. The equation is:
induced voltage = (-) N dΦ/dt
where N is the number of turns in the coil, Φ is the magnetic flux through the coil, and dΦ/dt is the time rate of change of magnetic flux.
Rearranging the equation, we get:
dΦ/dt = (-) induced voltage / N
Plugging in the given values, we get:
dΦ/dt = (-) 2.45V / N
Since we are not given the number of turns in the coil, we cannot calculate the time rate of change of magnetic flux. Therefore, the answer is D) None of These.

Learn more about Faraday's Law here: https://brainly.com/question/13369951

#SPJ11

The time rate of change of the magnetic flux is D) None of These because:

We can use Faraday's Law of Electromagnetic Induction to relate the induced voltage to the time rate of change of magnetic flux. The equation is:
induced voltage = (-) N dΦ/dt
where N is the number of turns in the coil, Φ is the magnetic flux through the coil, and dΦ/dt is the time rate of change of magnetic flux.
Rearranging the equation, we get:
dΦ/dt = (-) induced voltage / N
Plugging in the given values, we get:
dΦ/dt = (-) 2.45V / N
Since we are not given the number of turns in the coil, we cannot calculate the time rate of change of magnetic flux. Therefore, the answer is D) None of These.

Learn more about Faraday's Law here: https://brainly.com/question/13369951

#SPJ11

The kinetic energy of the ball at the highest point of its motion is 120,000 J.

The kinetic energy of a ball thrown at an initial angle of 30 degrees and a speed of 40.0 m/s can be determined using the equation, KE = (0.5)*m*v^2, where m is the mass of the ball and v is the speed. In this case, the mass of the ball is 0.150 kg and the speed is 40.0 m/s.

At the highest point of its motion, the ball is at rest, meaning its kinetic energy is zero. This does not mean, however, that the ball does not have any energy. It still has potential energy, which is equal to the kinetic energy the ball had at the start of its motion.

This is because the energy of a system is conserved, meaning that the total energy of the system will remain constant. As the ball moves higher, its kinetic energy is converted into potential energy. Thus, the kinetic energy at the highest point of its motion is equal to the kinetic energy at the start of its motion.

Know more about kinetic energy here

https://brainly.com/question/26472013#

#SPJ11

The magnitude of the force on the electron is approximately 2.99 x10 N

The force on an electron traveling horizontally to the east in a vertically upward magnetic field can be determined using the formula F = qvB sin(theta), where F is the force, q is the charge of the electron, v is the velocity of the electron, B is the magnetic field strength, and theta is the angle between the velocity and the magnetic field.

In this case, the electron is traveling horizontally to the east, so theta is 90 degrees (since the velocity and magnetic field are perpendicular). Thus, we can simplify the formula to F = qvB.

Substituting the given values, we get:
F = (1.602 x 10 C) x (5.95 x 10 m/s) x (0.25 T)
F = 2.99 x 10 N

This force is perpendicular to the direction of motion of the electron and is known as the magnetic force. It is caused by the interaction between the magnetic field and the moving charge of the electron. The magnitude of the force depends on the charge, velocity, and strength of the magnetic field.

For more such questions on Magnitude of Force, visit:

brainly.com/question/30033702

#SPJ11

To convert 65, 75, and 85 mi/h to units of m/s, you can use a loop or call the function multiple times with different input arguments.

Here's the MATLAB code for the user-defined function:
function mps = mphTOmets(mph)
% Converts speed given in units of miles per hour to speed in units of meters per second.
% Input argument is the speed in mi/h. Output argument is the speed in m/s.
mps = mph*0.44704;
end
To convert 55 mi/h to units of m/s, simply call the function with an input argument of 55:
>> mphTOmets(55)
ans =
  24.5872

Here's an example of using a loop:
>> mph_values = [65, 75, 85];
>> for i = 1:length(mph_values)
      mps_values(i) = mphTOmets(mph_values(i));
  end
>> mps_values
mps_values =

29.0576   33.5280   38.0384

To learn more about MATLAB Code : https://brainly.com/question/15980493

#SPJ11

(a) The maximum voltage that can be safely applied to the 100 Ω resistor is 12.25 V and the 25 kΩ resistor is 25 V.

(b) The maximum current that can be safely applied to the 100 Ω resistor is 0.387 A and the 25 kΩ resistor is 0.02 A.

(a) To determine the maximum voltage that can be safely applied to each resistor, we can use the formula P = V^2/R, where P is the maximum power output, V is the maximum voltage, and R is the resistance of the resistor.

For the 100 Ω resistor, the maximum voltage is:

[tex]V = sqrt(P*R) = sqrt(1.5 W * 100 Ω) = 12.25 V[/tex]

Therefore, the maximum voltage that can be safely applied to the 100 Ω resistor is 12.25 V.

For the 25 kΩ resistor, the maximum voltage is:

[tex]V = sqrt(P*R) = sqrt(0.25 W * 25,000 Ω) = 25 V[/tex]

Therefore, the maximum voltage that can be safely applied to the 25 kΩ resistor is 25 V.

(b) To determine the maximum current that each resistor can have, we can use the formula P = I^2 * R, where P is the maximum power output, I is the maximum current, and R is the resistance of the resistor.

For the 100 Ω resistor, the maximum current is:

[tex]I = sqrt(P/R) = sqrt(1.5 W / 100 Ω) = 0.387 A[/tex]

Therefore, the maximum current that can be safely applied to the 100 Ω resistor is 0.387 A.

For the 25 kΩ resistor, the maximum current is:

[tex]I = sqrt(P/R) = sqrt(0.25 W / 25,000 Ω) = 0.02 A[/tex]

Therefore, the maximum current that can be safely applied to the 25 kΩ resistor is 0.02 A.

To know more about maximum voltage click here:

https://brainly.com/question/15085835

#SPJ11

The values of Vs, Vd1, and Vd2 are 0.4 V,  -0.8 V, -0.4 V, -1.2 V and the input common-mode range is -2.7 V ≤ Vin ≤ -3.2 V.

For the given PMOS differential amplifier shown in the figure,

Jet V=-0.8 V

k,(W/L) 3.5 mA/V.

Let us neglect the channel-length modulation,

a) For Vg1 = Vg2 = 0 V, Vov for Q1 and Q2 is

Vov = √(2×ID/(k×(W/L)×Cox × Vgs))

Here

[tex]ID = k*(W/L)*Vov^{2/2}[/tex]

Cox = eox/tox

eox = 3.9×8.85×10⁻¹⁴ F/cm

tox = 100 A/cm²

Staging the given values in the above equations,

Vov = 0.4 V

Vgs = -1.2 V for Q1 and -0.4 V for Q2

Vs = -0.8 V

Vd1 = -0.4 V

Vd2 = -1.2 V

b) The input common-mode range is

Vcm_min = -Vss + Vcs + Vgs_min

HereHere

Vss = -1.5 V (given)

Vcs = 0 (since there is no voltage drop across current source)

Vgs_min = min(Vgs1, Vgs2) = -1.2 V (from part a)

Therefore,

Vcm_min = -1.5 + 0 + (-1.2) = -2.7 V

Vcm_max = -Vss + Vds_min + |Vtp|

where Vds_min = min(Vd1, Vd2) = -1.2 V (from part a)

|Vtp| is the threshold voltage of PMOS transistor which is given as -0.5 V (given)

Therefore,

Vcm_max = -1.5 + (-1.2) + |-0.5| = -3.2 V

Hence, the input common-mode range is -2.7 V ≤ Vin ≤ -3.2 V.

To learn more about amplifier

https://brainly.com/question/29671693

#SPJ4

The complete question is

For the PMOS differential amplifier shown in following figure, Jet V=-0.8 V and k,(W/L) 3.5 mA/V.

Neglect channel-length modulation.

a) For Vg1 = Vg2 = 0 V, find Vov and Vgs for each of Q1 and Q2. Also find Vs, Vd1, and Vd2.

b) If the current source requires a minimum voltage of 0.5V, find the input common-mode range.

The combined object moves at a speed of 2.0 m/s after the collision.

The principle of conservation of momentum is used to solve the collision problem between the two objects.

The principle states that the total momentum of a system of objects is conserved if no external forces act on the system. In this case, the initial momentum of the system, which is the sum of the momenta of the two objects before the collision, is equal to the final momentum of the system, which is the momentum of the combined object after the collision.

Here, we use

m1v1i + m2v2i = (m1 + m2)vf

Where m1 and v1i are the mass and initial velocity of the first object, m2 and v2i are the mass and initial velocity of the second object, and vf is the final velocity of the combined object.

After substituting values, we get:

(2 kg) (3.0 m/s) + (1 kg) (0 m/s) = (2 kg + 1 kg) vf

Simplifying the equation, we get:

6.0 kg·m/s = 3.0 kg vf

Solving for vf, we get:

vf = 2.0 m/s

Therefore, the combined object moves at a speed of 2.0 m/s after the collision.

To know more about conservation of momentum, click here

https://brainly.com/question/3920210

#SPJ1

The period of simple harmonic motion for a pendulum in a truck accelerating horizontally at 8.00 m/s^2 will be increased due to the additional force acting on the pendulum.

The period of a simple pendulum is affected by the acceleration due to gravity, the length of the pendulum, and the amplitude of the swing. In the case of a pendulum placed in a truck that is accelerating horizontally, the period is also affected by the acceleration of the truck. The period of the pendulum in this case can be found using the formula:

[tex]T = 2π * sqrt(L/g + a)[/tex]

where T is the period, L is the length of the pendulum, g is the acceleration due to gravity, and a is the horizontal acceleration of the truck. Substituting the given values into the formula, we can calculate the period of the pendulum.

Learn more about simple harmonic motion here:

https://brainly.com/question/30404816

#SPJ11

The maximum distance the spring is compressed is 0.143 m.

When the block is dropped onto the spring, it gains kinetic energy equal to mgh, where m is the mass of the block, g is the acceleration due to gravity, and h is the height from which it was dropped.

As the block compresses the spring, this kinetic energy is converted into elastic potential energy stored in the spring. At the maximum compression, all the kinetic energy is converted into elastic potential energy.

Using the conservation of energy, we can write:

mgh = (1/2)kx²

where x is the maximum distance the spring is compressed.

Solving for x, we get:

x = √(2mgh/k)

Substituting the given values, we get:

x = √(2(1.5 kg)(9.81 m/s²)(0.75 m)/(1880 N/m))

x ≈ 0.143 m

Therefore, the maximum distance is 0.143 m.

To know more about distance, refer here:
https://brainly.com/question/29132081
#SPJ11

The maximum temperature allowed for silicon is 383 degree Celsius.

The intrinsic carrier concentration, ni, in silicon can be determined using the following equation:

ni^2 = Nc * Nv * exp(-Eg/kT)

Rearranging the equation as follows:

T = Eg / (2 * k * ln(ni^2 / Nc / Nv))

The values of Nc and Nv can be calculated using the following equations:

Nc = 2 * [(2πmkT/h^2)^(3/2)]

Nv = 2 * [(2πmkT/h^2)^(3/2)] * exp(-Eg/kT)

Using typical values for the effective masses of electrons and holes in silicon (m_e = 0.26 m_0, m_h = 0.36 m_0, where m_0 is the rest mass of an electron), we can calculate Nc and Nv as:

Nc = 2.81 x 10^19 cm^-3

Nv = 1.83 x 10^19 cm^-3

Substituting these values into the equation for T, we get:

T = (1.12 eV) / [2 * (1.38 x 10^-23 J/K) * ln((1 x 10^12 cm^-3)^2 / (2.81 x 10^19 cm^-3) * (1.83 x 10^19 cm^-3))]

T = 656 K or 383 °C

Therefore, the maximum temperature allowed for silicon with an intrinsic carrier concentration no greater than 1x10^12 cm^-3 is approximately 656 Kelvin or 383 degrees Celsius.

learn more about intrinsic concentration here,

https://brainly.com/question/31324191

#SPJ11

Re x,crit = 2 105 is the essential Reynolds number for the ideal position of the trip wire.

The area of a larger flow field that is close to the surface and experiences strong impacts from wall frictional forces is referred to as a boundary layer flow. The velocity is almost parallel to the surface because the region of interest is close to the surface and the surface is believed to be impervious to the flow.

For laminar flow over a flat plate, the Nusselt number is given by:

[tex]Nu = 0.664(Re_x^1/2)(Pr^1/3)[/tex]

The Nusselt number is calculated for turbulent flow over a flat plate as follows:

[tex]Nu = 0.037(Re_x^4/5 - 100)(Pr)/(1 + 2.443(Re_x^(-1/2))(Pr^2/3))[/tex]

where Re_x is the Reynolds number at a distance x from the leading edge, and Pr is the Prandtl number of the fluid.

dNu/dRe_x = 0

For laminar flow, this gives:

[tex]Re_x,crit = 5 × 10^5[/tex]

For turbulent flow, this gives:

[tex]Re_x,crit = 2 × 10^5[/tex]

To know more about ideal position visit:-

https://brainly.com/question/13617569

#SPJ1

Question:

The boundary layer associated with parallel flow over an isothermal plate may be "tripped at any x-location by using a fine wire that is stretched across the width of the plate Determine the value of the critical Reynolds number Rexcrit, that is associated with the optimal location of the trip wire from the leading edge that will result in maximum heat transfer from a warm plate to a cooler fluid. Assume the Nusselt number correlations provided in the text for laminar and turbulent flows apply in the laminar and turbulent regions, respectively

The maximum distance the spring compresses is A) 0.25 cm or 2.5 × 10^-3 m.

The initial kinetic energy of the object is converted into elastic potential energy stored in the spring when it comes in contact with the spring. At the maximum compression, all the kinetic energy is converted into elastic potential energy.

The maximum compression of the spring is given by the equation ∆x = (mv^2)/(2k), where m is the mass of the object, v is its initial velocity, and k is the spring constant.

Plugging in the given values, we get ∆x = (4.0 kg × (5.0 m/s)^2)/(2 × 40,000 N/m) = 2.5 × 10^-3 m = 0.25 cm. Therefore, the maximum distance the spring compresses is 0.25 cm or 2.5 × 10^-3 m. The correct answer is (A).

For more questions like Distance click the link below:

https://brainly.com/question/15172156

#SPJ11

The gauge pressure in the water at the foot of the dam is E) 1.09 x 10⁶ Pa.

To calculate the gauge pressure at the foot of the Aswan High Dam, we can use the formula:

Gauge pressure = Density × Gravity × Height

Given that the density of water is 1000 kg/m³ and the height of the dam is 111 meters, we can plug in the values and use the standard acceleration due to gravity (approximately 9.81 m/s²):

Gauge pressure = (1000 kg/m³) × (9.81 m/s²) × (111 m)

Gauge pressure = 1,089,100 Pa

This value is closest to option E, so the correct answer is:

E) 1.09 x 10⁶ Pa

Learn more about gauge pressure here: https://brainly.com/question/30425554

#SPJ11

The wavelength of the laser beam is approximately 317 nm, which is in the ultraviolet range of the electromagnetic spectrum.

The energy of a photon can be calculated using the equation E=hc/λ, where E is the energy of the photon, h is Planck's constant, c is the speed of light, and λ is the wavelength of the photon. Using this equation and the given number of photons, we can calculate the total energy delivered by the laser beam in one second.

First, we need to calculate the energy of a single photon using the given laser power of 100 mW (0.1 W) and the time of one second:

Energy per photon = (100 mW x 1 s) / (1.6 x 10¹⁷ photons) = 6.25 x 10⁻¹⁶ J

Next, we can rearrange the equation for photon energy to solve for the wavelength:

λ = hc/E = (6.626 x 10⁻³⁴ J s) x (3.00 x 10⁸ m/s) / (6.25 x 10⁻¹⁶ J) = 3.17 x 10⁻⁷ m

To know more about electromagnetic spectrum click on below link:

https://brainly.com/question/15576247#

#SPJ11

At 0°C, the balloon filled with 400 m³ of helium at atmospheric pressure can lift a payload of approximately 446.425 kg.

To determine the mass that a balloon filled with 400 m³ of helium at atmospheric pressure can lift at 0°C, we need to use the Ideal Gas Law and consider the buoyant force. Here's the step-by-step explanation:
1. Write down the Ideal Gas Law: PV = nRT, where P is pressure, V is volume, n is the number of moles of gas, R is the gas constant, and T is the temperature in Kelvin.
2. Convert the temperature from Celsius to Kelvin: T = 0°C + 273.15 = 273.15 K.
3. Use the molar volume of an ideal gas at standard conditions (0°C and 1 atm) to determine the number of moles (n) of helium: V = 400 m³, and molar volume at standard conditions is 22.4 L/mol. Since 1 m³ = 1000 L, we have V = 400,000 L.
n = V / molar volume = 400,000 L / 22.4 L/mol ≈ 17,857 moles of helium.
4. Calculate the mass of helium in the balloon: mass = n ×molar mass of helium. The molar mass of helium is 4 g/mol.
mass_helium = 17,857 moles × 4 g/mol = 71,428 g = 71.428 kg.
5. Determine the buoyant force by considering the mass of the air displaced by the balloon. The molar mass of air is approximately 29 g/mol.
 mass_air = 17,857 moles × 29 g/mol = 517,853 g = 517.853 kg.
6. Calculate the payload mass: payload_mass = mass_air - mass_helium.
payload_mass = 517.853 kg - 71.428 kg ≈ 446.425 kg.
At 0°C, the balloon filled with 400 m3 of helium at atmospheric pressure can lift a payload of approximately 446.425 kg.

To learn more about atmospheric pressure https://brainly.com/question/13528807

#SPJ11

(a) The equation for p is p = p0 * e^(-h/k). (b) The pressure p at an altitude of 5 km is 51.5 kPa.

(a) To solve the equation for p, we have the formula:
ln(p/p0) = -h/k

First, let's rewrite the formula in terms of exponentials:
p/p0 = e^(-h/k)

Now, we want to isolate p, so we'll multiply both sides of the equation by p0:
p = p0 * e^(-h/k)

(b) To find the pressure p at an altitude of 5 km, we can plug in the values for h, k, and p0 into the equation we derived in part (a):
p = 100 * e^(-5/7)

Now, we can calculate the value of p:
p ≈ 100 * e^(-5/7) ≈ 100 * 0.515 ≈ 51.5 kPa

So, the pressure p at an altitude of 5 km is approximately 51.5 kPa.

Know more about pressure here:

https://brainly.com/question/28012687

#SPJ11

The momentum of the small rock at distance 2 is 1.08e+17 kg · m/s, in the -y direction.

What is momentum?

To solve this problem, we need to use the conservation of momentum. Since there are no other massive objects nearby, the total momentum of the system (rock + star) must be conserved.

At the first distance d1, the momentum of the rock can be split into two components: one in the x direction and one in the y direction. Using the angle α = 122 degrees, we can calculate the x and y components of the momentum:

p1x = p1 * cos(α) = 1.15e+17 kg · m/s * cos(122°) = -3.97e+16 kg · m/s

p1y = p1 * sin(α) = 1.15e+17 kg · m/s * sin(122°) = 1.08e+17 kg · m/s

Since there are no external forces acting on the system, the momentum in the x direction and the momentum in the y direction must be conserved separately. However, since the path of the rock is not given, we cannot assume that the momentum in the x direction is conserved. Therefore, we need to calculate the new momentum of the rock in the y direction at distance d2.

To do this, we can use the conservation of momentum in the y direction:

p1y = p2y

where p2y is the momentum of the rock in the y direction at distance d2.

We can rearrange this equation to solve for p2y:

p2y = p1y = 1.08e+17 kg · m/s

Therefore, the momentum of the small rock at distance 2 is 1.08e+17 kg · m/s, in the -y direction.

To know more about momentum, visit:

https://brainly.com/question/20125215

#SPJ1

When the circuit is first completed, the voltage drop across the capacitor is 0 V. Just after the circuit is completed, the capacitor will act as an open circuit since it is initially uncharged. Therefore, all the voltage will drop across the resistor.

1. Initially, the capacitor is uncharged, which means it has no charge stored in it.
2. When the circuit is completed, the current starts flowing from the emf source through the resistor and towards the capacitor.
3. However, just after the circuit is completed, no time has passed for the capacitor to charge. Therefore, the voltage across the capacitor is still 0 V.
4. As time progresses, the capacitor will start charging and the voltage across it will increase, but just after the circuit is completed, the voltage drop across the capacitor remains 0 V.
Using Ohm's Law, we can find the voltage drop across the resistor: V = IR where I is the current flowing through the circuit.
Using the total resistance of the circuit: R_total = R + R_capacitor
we can find the current: I = ε / R_total
Plugging in the given values:
R_total = 7.40 kΩ + 0.00 kΩ = 7.40 kΩ
I = 100 V / 7.40 kΩ = 0.0135 A
Now we can find the voltage drop across the resistor:
V = IR = 0.0135 A * 7.40 kΩ = 99.9 V
Therefore, the voltage drop across the capacitor is 0 V.

To learn more about voltage drop click here https://brainly.com/question/31431320

#SPJ11

The cars move with a velocity of 0.713 m/s just after the collision.

By dividing the amount of time it took the object to move a certain distance by the overall distance, one can calculate the object's initial velocity. V is the velocity, d is the distance, and t is the duration in the equation V = d/t.

According to the rule of conservation of momentum, the total amount of momentum before a collision equals the total amount of momentum after the contact.

We can thus write:

m1v1i = (m1 + m2)vf

We can solve for vf as follows:

vf = (m1v1i) / (m1 + m2)

Inputting the numbers provided yields:

vf = (18.0 kg x 100 kg·m/s) / (18.0 kg + 43.0 kg)

= 45.7 kg·m/s

Therefore, the velocity of the cars just after the collision is:

v = vf / (m1 + m2)

= 45.7 kg·m/s / (18.0 kg + 43.0 kg)

= 0.713 m/s

To know more about collision visit:-

https://brainly.com/question/26019704

#SPJ1

a) The magnetic force on a charged particle moving with velocity v in a magnetic field B is given by the formula:

F = q v B sinθ

where q is the charge of the particle and θ is the angle between v and B.

In this case, the proton has charge q = +1.602 x 10[tex]^-19[/tex]C, the magnetic field strength is B = 4.3 x 10[tex]^-3[/tex] T, and θ = 90° - 39° = 51° (since the proton is traveling at an angle of 39° with respect to the magnetic field, the angle between v and B is 90° - 39° = 51°).

Substituting these values and the given force F = 5.0 x 10[tex]^-17[/tex] N into the formula, we can solve for the proton's speed v:

F = q v B sinθ

Therefore, the proton's speed is approximately 1.32 x 10[tex]^5[/tex] m/s.

b) The kinetic energy of the proton can be calculated using the formula:

K = (1/2) m v[tex]^2[/tex]

where m is the mass of the proton (which is approximately 1.67 x 10[tex]^-27[/tex]kg).

Substituting the values of m and v, we get:

K = (1/2) m v[tex]^2[/tex] = (1/2) (1.67 x 10[tex]^-27[/tex] kg) (1.32 x 10^5 m/s)[tex]^2[/tex] ≈ 1.14 x 10[tex]^-14 J[/tex]

Therefore, the kinetic energy of the proton is approximately 1.14 x 10[tex]^-14 J[/tex]J.

To know more about magnetic force  here

https://brainly.com/question/2279150

#SPJ4

The potential at q is 120 volts. This is found by calculating the equivalent resistance of the circuit, using voltage division to find the potential difference across r2, and adding it to the potential at p.

To find the potential at q, we first need to find the equivalent resistance of the circuit. Using the formula for resistors in series and parallel, we get:
[tex]Req = r1 + r2 = 3.0 ω + 2.0 ω = 5.0 ω[/tex]

Next, we can use the formula for voltage division to find the potential difference across r2 and therefore the potential at q. The formula is:

[tex]V2 = ℰ2 * (Req / (r1 + Req)) = 50 v * (5.0 ω / (3.0 ω + 5.0 ω)) = 20 v[/tex]

Finally, we can add the potential difference V2 to the potential at p to get the potential at q:

[tex]Vq = Vp + V2 = 100 v + 20 v = 120 v[/tex]

Therefore, the potential at q is 120 volts.

learn more about resistance here:

https://brainly.com/question/30799966

#SPJ11

The prevailing winds that are most likely between 30° N and 60° N are the westerlies.

These are strong winds that blow from west to east, and they are responsible for weather patterns in many parts of the world. The westerlies are often found in the middle latitudes and are sandwiched between the polar easterlies to the north and the trade winds to the south.They are created by the differences in air pressure between the high pressure systems in the subtropics and the low pressure systems in the mid-latitudes. As the air moves from the high pressure systems to the low pressure systems, it is deflected to the right by the Coriolis Effect, resulting in the westerly winds.

learn more about pressure Refer: https://brainly.com/question/20909989

#SPJ11

The downward pull of the briefcase on the woman's arm while the elevator is accelerating is 18.1 N (upward).

The free-body diagram for the briefcase shows two forces acting on it: the force of gravity and the upward force exerted by the woman's arm. Since the elevator is accelerating downward, the force of gravity is greater than the upward force, causing a net downward force on the briefcase.

To calculate the downward pull of the briefcase on the woman's arm, we need to use Newton's second law, which states that the net force on an object is equal to its mass times its acceleration:

[tex]F_net = m*a[/tex]

where F_net is the net force, m is the mass of the briefcase, and a is the acceleration of the elevator.

The force exerted by the woman's arm is an upward force, which is opposite in direction to the net downward force on the briefcase. Therefore, we need to subtract the force exerted by the woman's arm from the force of gravity on the briefcase to get the net force:

[tex]F_ne[/tex]t = ma = (2.2 kg)(1.60 m/s[tex]^2[/tex]) = 3.52 N (downward)

[tex]F_gravity[/tex] = mg = (2.2 kg)(9.81 m/s[tex]^2[/tex] ) = 21.6 N (downward)

[tex]F_net = F_gravity - F_arm[/tex]

[tex]F_arm = F_gravity - F_net[/tex]= 21.6 N - 3.52 N = 18.1 N (upward)

Therefore, the downward pull of the briefcase on the woman's arm while the elevator is accelerating is 18.1 N (upward).

To know more about accelerating here

https://brainly.com/question/460763

#SPJ4